CASIO金属表带之拆带教程VIP

CASIO金属表带之拆带教程（多图）有不少朋友不会自己拆表带,发个别的网上看来的拆表带教程CASIO金属表带之拆带教程（多图） 1.把环状的表带从表扣处暂时拆开，让表带可以平摊在桌面上。以利于下一步的动作。最好下边垫一块绒布，可以 .02.jpg (45.16 KB) 03.jpg (41.88 KB) 04.jpg (62.54 KB) 05.jpg (55.07 KB) 2.把表带平摊后，用一尖头的工具（我用的是小剪刀）顺着表带后背的箭头找到插销的位置，抵着圆形的小凸起， .06.jpg (57.58 KB) 07.jpg (56 KB) 3.拆下插销后，沿连接处的缺口轻轻一拧，就能拆开表带08.jpg (65.49 KB) 09.jpg (65.49 KB) 4.要取下一节表带，就要把首尾相邻的两个插销都要拆出10.jpg (62.22 KB) 5.拆掉合适长度的表带后，就可以把表带装回去了。插销口可能会有点紧，找样软硬适中的东西（我拿的是塑料火 .130T-7V拆钛表带之实录（多图）之前看了坛友的拆表带教呈，对我帮助很大，今天狠下心来也不去表铺上的宰了决定听从毛主席的教道，自己动手，丰衣足食话不多说上图才是王道准备好工具DSC00811.JPG (74.99 KB) 2008-10-6 20:41 天气情好，气压图却下跌不解？DSC00812.JPG (46.09 KB) 2008-10-6 20:41 DSC00813.JPG (50.74 KB) 2008-10-6 20:41 传说中的苍蝇眼睛DSC00814.JPG (67.1 KB) 2008-10-6 20:41 在的下面有一排数字不知道是什么意思？谁说一下DSC00815.JPG (41.75 KB) 2008-10-6 20:41 照的不是很清楚看到了吗？DSC00816.JPG (73.16 KB) 2008-10-6 20:41 话撤远了，开始上正题DSC00817.JPG (49.24 KB) 2008-10-6 20:41 对准小洞，顶进去DSC00818.JPG (57.85 KB) 2008-10-6 20:41 看到对面的小钉出来了呀DSC00819.JPG (74.8 KB) 2008-10-6 20:41 这时候销钉还出不来，用钳子把他拔出来就可以了DSC00820.JPG (50.47 KB) 2008-10-6 20:41 注意还有个小套筒不要弄丢了DSC00821.JPG (69.5 KB) 2008-10-6 20:41 拆好表带合适了后，上弹簧销DSC00822.JPG (68.05 KB) 2008-10-6 20:41 压下去DSC00823.JPG (70.63 KB) 2008-10-6 20:41 完工，下了节表扣DSC00826.JPG (63.35 KB) 2008-10-6 20:41 为省钱自己动手为EF卸表带上次去表店里卸了一下表带，3元，现在带着，觉得还是有点长，想卸掉一节，由于自己就找来工具，主要还是回形针一个，敲敲打打，就被我卸下一个，省钱3元2008-5-13 12:47 2.jpg (71.91 KB) 2008-5-13 12:49 3.jpg (120.16 KB) 2008-5-13 12:49 4.jpg (61.8 KB) 2008-5-13 12:49 G-Shock bracelet are most ot the time hold together with mini springbars, but there are also models with a spltpin conection between the links.First of all you can open the bracelet, by removing the springbar at the clasp. Always be carefull with removing spring bars, so that they not jump away. I always try to put a finger in the jumping line so if a springbar jumps away accidentally, its direct stopped at my finger, so it wont get lost.Split Pin Bracelet:The best way to remove links is with the special tool, but in the past I have succeeded with a very small nail or something similar too.To remove links you need to repeat this operation. Always try to remove the same amount of links from each side of the buckle, so your buckle stays in the middle under your wrist.Putting the links together can be done best with a plastichead hammer.Beware that you use a solid underground, so the bracelet doesnt slip away and get scratched. The last bit you can push the pin into the links with the sharp point of a springbar tool. A small nail or screw can do the trick also if you dont have one.For fine adjusting, see under Springbar Barcelet:When you have opened the bracelet as shown above, youll se in hte inside small holes and arrows. If you look good, youll see the head of the springbar. Its a bit tricky to remove the springbar, but if you have done it several times, you get more handy it opening them. You can use a small springbar remover, but a very small screwdriver might do the trick too or even better. I have several springbar removing tools, but only one is OK for this job.Like with the split pin bracelet, you need to repeat this operation several times to remove the links. Also here try to remove the same amount of links on each side of the clasp.How tight you want your bracelet is mostly a matter of preference. Dont make the bracelet smaller than in the next picture. It must always be ossible to put a finger under the clasp.If you have the following problem:One link too many is too loose, one link removed, its too tight, you can fine adjust the clasp.In the clasp you can rewsize the bracelet in 1/2 or 1/3 link size. If you look closely in the clasp, youll notice two or three holes, where your bracelet can be attached to the clasp on one side:Like in the second picture, it isnt a