




已阅读5页,还剩12页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
Hong Kong Airlines LimitedHong Kong Air Cargo Carrier Limited香港航空有限公司香港货运航空有限公司F-D-099Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA335067_204_443IDI 5067443Training and Qualification/培训和资格Technical Record/技术记录IDINONETitleOperational Test of the Left Hand Escape-FacilitiesMcd&Rev/厂家工卡&修订日期标题操作测试左侧应急逃离滑梯AMM 25-62-41-400-801-AAMM 25-62-41-400-802-A 2018-01-01A/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BLNZAT-H25-62-41-001LHR001006客舱/CabinTINP2.0MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检HA33-25-LNME-050ME,HKAN 12 A16ISS 3 REV 1PVG1095 CA1095 CAAccess Panels/接近盖板Zones/区域Written/编写Approved/批准NONENONE卢华周枫2018-01-252018-01-25TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注198A24403000000CABLE HOLDING STRAPTO1ALL(必需/Necessary)298A52107632000PIN - SAFETY SLIDETO4ALL(必需/Necessary)TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释:请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HKE Approval No: AI /218/1215, JMM 133 * HNAT Approval No.: D.101115, JMM 047* CASL Approval No: AI / 101 / 798 * AMECO Approval No.: D100001, JMM 001* HNAT- North West Approval No.: D.500023, JMM 049 * HAECO Approval No: DAI / 1 / 853 * SMECO Approval No.: D.400009, JMM 081* HNAT- YN Approval No.: D.4108, JMM 134 * TAECO Approval No.: DAI / 89 / 1295 * CEA Approval No.: D.200002, JMM 112 * HNAT Approval No.: D.3039, JMM 076 * THAECO Approval No.: D.101661, JMM 124 * CEA-Jiangsu Approval No.: D.200047, JMM 117 * SPRING Approval No.: D.200081, JMM 121 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: D.200078,JMM 039* GAMECO Approval No.: D.300001, JMM 006* THAI Approval No.: AI / 147 / 0910 * Other: *Signature:_ Authorization No.:_ Date:_AT-H25-62-41-001L HR001006 W/O:5067 AC:BLNZ页码:2 / 17工卡Job card:HA33-25-LNME-050TITLEOperational Test of the Left Hand Escape-FacilitiesPerfInsp标题操作测试左侧应急逃离滑梯工作者检查者1.Job set-up 工作准备A. Aircraft Maintenance Configuration T 飞机维护构型(1) Energize the ground service network . 接通地面勤务电源。(2) Energize the Cabin Intercommunication Data System (CIDS) (Ref. AMM TASK 23-73-00-861-801) . 给客舱信息互联数据系统接通电源(Ref. AMM TASK 23-73-00-861-801)。(3) Do the operational test of the emergency lights (Ref. AMM TASK 33-51-00-710-801) . 进行应急灯操作测试(Ref. AMM TASK 33-51-00-710-801)(4) Put a WARNING NOTICE(S) on the applicable door to tell persons not to open the door, during the test. 在相关门上挂上警告牌,警告他人在测试过程中禁止操作门。2.Operational test/操作测试* ON A/C CRK 401-500适用于手册有效号为CRK 401-500的飞机Subtask25-62-41-710-050-AA. Do the operational test of the monitoring, through CIDS. 通过CIDS,进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Left Hand)NOTE: Two persons are necessary to do the test.注 释:必须至少两人执行这个测试。ACTION/操作RESULT/结果IDI1. T On the related pack-assembly: 在相关滑梯包组件上:Remove the safety pin (1).IDI T 撤除安全销(1)。2. On the Programming Indication Module (PIM): 在程序指示组件(PIM)上:Push the key DOORS (3). 按压DOORS键(3)。On the PIM monitor (2):在PIM显示器(2)上:No message CHECK SLIDE PRESSURE for the related door is shown. 没有显示相关门的CHECK SLIDE PRESSURIDI T 信息。3. On the related pack-assembly: 在相关滑梯包组件上:Install the safety pin (1)(Ref.AMM TASK 25-62-00-860-801).IDI T 安装安全销(1)(Ref.AMM TASK 25-62-00-860-801)。4. On the PIM: 在PIM上:Push the key DOORS (3). 按压DOORS键(3)。On the PIM monitor (2) the related message:在PIM显示器(2)上显示以下相关信息:CHECK SLIDE PRESSURE: 1L or, CHECK SLIDE PRESSURE: 1L 或者CHECK SLIDE PRESSURE: 2L or, CHECK SLIDE PRESSURE: 2L 或者CHECK SLIDE PRESSURE: 4L is shown. CHECK SLIDE PRESSURE: 4L。* ON A/C CHH ALLON A/C CRK 001-300, 351-400ON A/C SIA ALL适用于CHH所有的飞机适用于手册有效号为CRK 001-300, 351-400的飞机适用于SIA所有的飞机Subtask25-62-41-710-050-BA. Do the operational test of the monitoring, through CIDS. 通过CIDS,进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Left Hand ) NOTE: Two persons are necessary to do the test. 注 释:必须至少两人执行这个测试。ACTION/操作 IDI T RESULT/结果1.At the Flight Attendant Panel (FAP) 120RH: 在飞行乘务面板120RH上:At the FAP 120RH: 在飞行乘务面板120RH上:- If the display screen is off, touch the screen surface.如果显示屏关闭,触摸一下屏幕表面。- The CABIN STATUS page comes on. 显示客舱模式CABIN STATUS页面。- Select the Doors/slides key (2).选择门/滑梯键(2)。- The DOORS/SLIDES page shows the related door (1L, 2L, 4L) amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门(1L, 2L, 4L)呈琥珀色显示,且显示信息SLIDE DISARMED 和CHECK SLIDE PRESSURE。 IDI T 2. At the related door: 在相关门上:- Remove the safety pin (1) (Ref. AMM TASK 25-62-00-860-803) . 拆除安全销(1)(Ref.AMM TASK 25-62-00-860-803) 。 IDI T 3. At the FAP 120RH:在FAP 120RH面板上:- Select the Doors/Slides key (2). 选择DoorsSlides键(2)。- The DOORS/SLIDES page shows the related door (1L, 2L, 4L) amber, and the message SLIDE DISARMED. IDI T 在DOOR/SLIDES页面上相关门(1L, 2L, 4L)呈琥珀色显示,且显示信息SLIDE DISARMED。4.At the related door: 在相关门上:- Remove the PIN - SAFETY SLIDE (98A52107632000) (4) and set the emergency control-handle(3) to the ARMED position. 拆除安全销(98A52107632000)(4),将紧急控制手柄(3)设置在ARMED位。WARNING: DO NOT OPEN THE DOOR WHEN THE EMERGENCY CONTROL-HANDLE IS SET IN THE ARMED POSITION.IF YOU DO, YOU WILL OPERATE THE ESCAPE-SLIDE RELEASE SYSTEM. THIS CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. IDI T 警 告:当紧急控制手柄在ARMED位时,不要打开门,否则,将释放紧急滑梯包,将可能造成人员受伤或设备损坏。5. At the FAP 120RH: 在FAP 120RH面板上: - Select the Doors/Slides key (2). 选择DOOR/SLIDES键(2)。- The DOORS/SLIDES page shows the related door (1L, 2L, 4L) green, and the message SLIDE DISARMED goes off. IDI T 在DOOR/SLIDES页面上相关门(1L, 2L, 4L)呈绿色显示,且 显示的信息SLIDE DISARMED将消失。6. At the related door: 在相关门上:- Set the emergency control-handle to the DISARMED position and install the PIN-SAFETY SLIDE (98A52107632000) (4). 将紧急控制手柄设置在DISARMED位,并且安装安全销(98A52107632000)(4)。- Install the safety pin (1) (Ref. AMM TASK 25-62-00-860-801) . IDI T 安装安全销(1) (Ref.AMM TASK 25-62-00-860-801) 。7. At the FAP 120RH: 在FAP 120RH面板上:- Select the Doors/Slides key (2).选择Doors/Slides键(2)。- The DOORS/SLIDES page shows the related door (1L, 2L, 4L) amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门(1L, 2L, 4L)呈琥珀色显示,且显示信息SLIDE DISARMED和CHECK SLIDE PRESSURE。* ON A/C CRK 302-350 ON A/C HKC ALL 适用于手册有效号为CRK 302-350的飞机适用于HKC所有的飞机Subtask25-62-41-710-051-AA. Do the operational test of the monitoring, through CIDS. 通过CIDS,进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Left Hand)NOTE: Two persons are necessary to do the test. 注 释:必须至少两人执行这个测试。ACTION/操作 IDI T RESULT/结果1. At the Flight Attendant Panel (FAP) 120RH: 在飞行乘务面板120RH上:At the FAP 120RH: 在飞行乘务面板120RH上:- If the display screen is off, touch the screen surface.如果显示屏空白,触摸一下屏幕表面。- The CABIN STATUS page comes on. 显示客舱模式。- Select the Doors/slides key (2).选择门/滑梯键(2)。- The DOORS/SLIDES page shows the related door amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. IDI T 在DOOR/SLIDES页面上相关门呈琥珀色显示,且显示信息SLIDE DISARMED 和CHECK SLIDE PRESSURE。2. On the related door: 在相关门上:- Remove the safety pin (1) (Ref. AMM TASK 25-62-00-860-803) . 拆除安全销(1)(Ref.AMM TASK 25-62-00-860-803) 。 IDI T 3. At the FAP 120RH:在FAP 120RH面板上:- Select the Doors/Slides key (2). 选择Doors/Slides键(2)。- The DOORS/SLIDES page shows the related door amber, and the message SLIDE DISARMED. IDI T 在DOOR/SLIDES页面上相关门呈琥珀色显示,且显示信息SLIDE DISARMED。4. At the related door: 在相关门上:- Remove the PIN - SAFETY SLIDE (98A52107632000) and set the emergency control-handle to the ARMED position. 拆除安全销(98A52107632000),将紧急控制手柄设置在ARMED位。WARNING: DO NOT OPEN THE DOOR WHEN THE EMERGENCY CONTROL-HANDLE IS SET IN THE ARMED POSITION.IF YOU DO, YOU WILL OPERATE THE ESCAPE-SLIDE RELEASE SYSTEM. THIS CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. IDI T 警 告:当紧急控制手柄在ARMED位时,不要打开门,否则,将释放紧急滑梯包,将可能造成人员受伤或设备损坏。5. At the FAP 120RH: 在FAP 120RH面板上:- Select the Doors/Slides key (2). 选择DOOR/SLIDES键(2)。- The DOORS/SLIDES page shows the related door green, and the message SLIDE DISARMED goes off. IDI T 在DOOR/SLIDES页面上相关门呈绿色显示,且 显示的信息SLIDE DISARMED将消失。6. On the related door: 在相关门上:- Set the emergency control-handle to the DISARMED position and install the PIN - SAFETY SLIDE (98A52107632000)(1) . 设置应急控制手柄至DISARMED并安装PIN - SAFETY SLIDE(98A52107632000)(1)。Install the safety pin(1) (Ref.AMMTASK25-62-00-860-801). 安装安全销(1)(Ref.AMMTASK25-62-00-860-801)。 IDI T 7. At the FAP 120RH: 在FAP 120RH面板上:- Select the Doors/Slides key (2).选择Doors/Slides键(2)。- The DOORS/SLIDES page shows the related door amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门呈琥珀色显示,且显示信息SLIDE DISARMED和CHECK SLIDE PRESSURE。* ON A/C ALL 适用于所有飞机3. Close-up/工作结束A. Close Access T 关闭接近(1) Make sure that the work area is clean and clear of tools and other items. 确认工作区域干净,无工具和其它物品。(2) Arm the pack assembly (Ref. AMM TASK 25-62-00-860-803) . 预位滑梯包组件。(Ref. AMM TASK 25-62-00-860-803)。(3) Put the door back to a serviceable condition (Ref. AMM TASK 52-10-00-860-802) . 将门恢复至可用状态。(Ref. AMM TASK 52-10-00-860-802)(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items. 撤除地面支撑和维护设备,以及特殊和标准工具及其它物品。B.De-energize the aircraft electrical circuits (Ref.AMMTASK24-41-00-862-801). T 断开飞机电源(Ref.AMMTASK24-41-00-862-801)。AT-H25-62-41-001L HR001006 2018-01-25页码,8 / 17工卡Job card:HA33-25-LNME-050TITLEOperational Test of the Left Hand Escape-FacilitiesPerfInsp标题操作测试左侧应急逃离滑梯工作者检查者Figure 25-62-41-991-00600-00-A / SHEET 1/2 - Monitoring, through CIDS Left Hand* ON A/C CRK 401-500Figure 25-62-41-991-00600-00-A / SHEET 2/2 - Monitoring, through CIDS Left Hand* ON A/C CRK 401-500Figure 25-62-41-991-00600-00-B / SHEET 1/3 - Monitoring, through CIDS Left Hand* ON A/C CRK 001-300, 351-400 ON A/C CHH ALL ON A/C SIA ALLFigure 25-62-41-991-00600-00-B / SHEET 2/3 - Monitoring, through CIDS Left Hand* ON A/C CRK 001-300, 351-400 ON A/C CHH ALL ON A/C SIA ALLFigure 25-62-41-991-00600-00-B / SHEET 3/3 - Monitoring, through CIDS Left Hand* ON A/C CRK 001-300, 351-400 ON A/C CHH ALL ON A/C SIA ALLFigure 25-62-41-991-01200-01-A / SHEET 1/2 - Monitoring, through CIDS Left Hand* ON A/C CRK 302-350 ON A/C HKC ALLFigure 25-62-41-991-01200-01-A / SHEET 2/2 - Monitoring, through CIDS Le
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2025最简单采购合同范本
- 江苏省合格性考试数学试卷
- 江苏省二年级数学试卷
- 2025农产品销售担保合同
- 2025海域使用权转让合同范本
- 2025年综合类-招标采购专业知识与法律法规-招标采购项目管理-第五章招标采购项目管理历年真题摘选带答案(5卷100道集锦-单选题)
- 2025年综合类-房地产经纪专业基础-房地产投资和风险历年真题摘选带答案(5卷100道集锦-单选题)
- 2025年综合类-房地产交易制度政策-房地产交易制度政策-房地产经纪专业人员历年真题摘选带答案(5卷100道集锦-单选题)
- 2025年综合类-建设工程技术与计量(土建工程)-第四节水泥历年真题摘选带答案(5卷100道集锦-单选题)
- 江西教招中学数学试卷
- 静脉导管常见并发症临床护理实践指南(上)
- 《妇产科学绪论》课件
- DB21T 3103-2019 油松容器育苗技术规程
- 高三地理备考总结
- GB/T 44570-2024塑料制品聚碳酸酯板材
- 《战略人力资源管理》彭剑峰
- 供应商备库协议书范文模板下载
- GB/T 16288-2024塑料制品的标志
- 2024新版PEP三年级上册U3-Amazing-animals-start-to-read教学课件
- TSG ZF003-2011《爆破片装置安全技术监察规程》
- 彩椒棚室栽培技术规程
评论
0/150
提交评论