海尔冰柜说明书

bcd 195wt2009-6-24 17:4601,2,3,4,5,6,713 3035 163057 163051502009-6-24 19:17 .,.1. 572. .-12.2009-6-24 186-24 18:03 bcd 195wt1,2,3,4,5,6,71-72-310 2009-6-24 21:07 bc-117fc 2010-10-09 10:03 haier bc-117fc2011-4-2 15:37r600a. 2011-4-2 16:37 r134ar-134ahfc-134acfc-12r12 r-134acfc-12hfc-134acfc-12hfc-134a 2011-4-2 15:57.r600ar122011-4-2 16:00117fcr134a2011-4-2 16:01c4h102011-4-2 16:38 (haier)bc-117fc 2011-2-10 11:58451334bc-117fc2011-8-29 12:04 bc-117fc2011-6-9 11:34bc-117fc,2011-6-10 07:58 2011-6-9 11:36bc117fc2011-8-25 15:58 bc-117fc2011-5-19 15:5834. 0550862011-5-20 23:281. 23bc-117fc,?2009-7-10 10:0272bc-117fc,.,2.,.,? ?2009-7-10 11:20,bc-117fc12008-6-20 13:56 ,!,!2008-6-20 13:47bc-117fc 2011-6-15 22:22 6.12 14 2011-6-15 22:42 7 2011-6-16 00:39; ,2011-6-16 10:312011-6-16 11:55bc-117fc2011-8-29 12:04bc117fchxc-358temperature recorderthis manual us applicable to blood bank refrigerators, medical, low temperature, and ultra low temperature duct features:the product mainly applies to blood bank refrigerators, ultra lowtemperature freezers and other medical equipment that requirestemperature recording over time(,)the record chart paper is circular. reading of temperature is simple and reliable. the operation of the unit is rather straightforward.()the unit is designed to operate with a precise microchip to ensure an accurate and reliable recording of time.(,)the recorder is also designed with a special circuitry to protect the operation of the motor from external electronic disturbance.()ambient conditions()please perform operation under the following conditions in order to accuracy.(,)indoor use;(;)elevation above sea lever2,000m;(m)ambient temperature within -1050;ambient humidity within0%90%rh;the fluctuation of voltage of the main power supply without exceeding the rated voltage.()installations of power line and sensor lineunscrew the two fixing screws outboard panel.()connect power line and sensor line into power socket connector and sensor socket ()connectorconnection is respectively. illustrated the with power the line following diagram.()rear view of recorder panel() battery buckle line(),driven motor of embossing stylus, connection terminal of sensor, connection terminal of power supply,driven motor of recording paperinstallationinstallation of instrumentthis recorder is mounted through the opening window on your instrument viaself-tapping screws on the recorder mounting plate.()operating guidesselection of temperature rangesafter temperature recorder is powered on, press key #3 for 5 seconds until hearing ticking by buzzer to let the recorder enter the option mode. press key #1 to choose temperature range. each pressing of this key will rotate the option to choose one of three temperature ranges. each temperature range is identified with the color of the indicator light.(,# 3 5,# 1)- 40+30:green;resolution:1- 115+50:yellow; resolution:5- 2000:red; resolution:5press key #2 to choose the recording time cycle. each pressing of this key will alternate the option of choosing the two time recording periods distinguished with the counts of buzzer.24 hour recording time cycle: rapid and short buzz;7 day recording time cycle: constant and long buzz;notice:a) after selecting a new temperature range or recording time cycle, a new calibration procedure for paper loading must be performed. otherwise the above operation cannot be accepted and saved by the temperature recorder.(,)b) if there is no new selection of temperature range and recording time cycle after it powers on for 5 seconds, the temperature recorder will automatically enter the mode of paper loading calibration. temperature selection and recording time are based on the prior settings before the last power shut down.(5,)paper loading/changingwhen the temperature recorder is in normal operation, press the #3 key. the embossing stylus moves 5 mm away from the outer edge of chart paper. the circular chart paper can then be replaced.(,35)2)perform calibration: press the #3 key again. the embossing stylus returns to the scale point b1 ( lower fcd-jthml fcd-