WOHA33_5235431_200_AT-H25-62-41-001R

Hong Kong Airlines LimitedHong Kong Air Cargo Carrier Limited香港航空有限公司香港货运航空有限公司F-D-099Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA335235_200_431DIC 5235431Training and Qualification/培训和资格Technical Record/技术记录DICNONETitleOperational Test of the Right Hand Escape-FacilitiesMcd&Rev/厂家工卡&修订日期标题操作测试右侧应急逃离滑梯AMM 25-62-41-400-804-AAMM 25-62-41-400-803-A2018-01-01A/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BLNWAT-H25-62-41-001RHR001005客舱/CabinTINP02:00MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检HA33-25-LNME-050ME,HKAN 12 A16ISS 3 REV 0PVG1095 CA1095 CAAccess Panels/接近盖板Zones/区域Written/编写Approved/批准NONENONE2018-01-252018-01-25TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注198A24403000000CABLE HOLDING STRAPTO1ALL(必需/Necessary)298A52107632000PIN - SAFETY SLIDETO4ALL(必需/Necessary)TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HKE Approval No: AI /218/1215, JMM 133 * HNAT Approval No.: D.101115, JMM 047* CASL Approval No: AI / 101 / 798 * AMECO Approval No.: D.101131, JMM 001* HNAT- North West Approval No.: D.500023, JMM 049 * HAECO Approval No: DAI / 1 / 853 * SMECO Approval No.: D.400009, JMM 081* HNAT- YN Approval No.: D.4108, JMM 134 * TAECO Approval No.: DAI / 89 / 1295 * CEA Approval No.: D.200002, JMM 112 * HNAT Approval No.: D.3039, JMM 076 * THAECO Approval No.: D.101661, JMM 124 * CEA-Jiangsu Approval No.: D.200047, JMM 117 * SPRING Approval No.: D.200081, JMM 121 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: D.200078,JMM 039* GAMECO Approval No.: D.300001, JMM 006* THAI Approval No.: AI / 147 / 0910 * Other: *Signature:_ Authorization No.:_ Date:_AT-H25-62-41-001R HR001005 W/O:5235 AC:BLNW页码：2 / 16工卡Job card:HA33-25-LNME-050TITLEOperational Test of the Right Hand Escape-FacilitiesPerfInsp标题操作测试右侧应急逃离滑梯工作者检查者1.Job set-up 工作准备A. Aircraft Maintenance Configuration T 飞机维护构型(1) Energize the ground service network . 接通地面勤务电源。(2) Energize the Cabin Intercommunication Data System (CIDS) (Ref. AMM TASK 23-73-00-861-801) . 给客舱信息互联数据系统接通电源(Ref. AMM TASK 23-73-00-861-801)。(3) Do the operational test of the emergency lights (Ref. AMM TASK 33-51-00-710-801) . 进行应急灯操作测试(Ref. AMM TASK 33-51-00-710-801)(4) Put a WARNING NOTICE(S) on the applicable door to tell persons not to open the door, during the test. 在相关门上挂上警告牌，警告他人在测试过程中禁止操作门。2.Operational test/操作测试* ON A/C CRK 401-500 适用于手册有效号为CRK 401-500的飞机Subtask25-62-41-710-053-AA. Do the operational test of the monitoring, through CIDS.通过CIDS，进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Right Hand) NOTE: Two persons are necessary to do the test.注 释：至少必须两人执行此测试。ACTION/操作RESULT/结果DIC T 1. On the related pack-assembly:在相关滑梯包组件上：Remove the safety pin (1).DIC T 撤除安全销(1)。2. On the Programming Indication Module (PIM): 在程序指示组件（PIM）上：Push the key DOORS (3).按压DOORS键(3)。On the PIM monitor (2):在PIM显示器(2)上：No message CHECK SLIDE PRESSURE for the related door is shown. 没有显示相关门的CHECK SLIDE PRESSUR T DIC信息。3. On the related pack-assembly: 在相关滑梯包组件上：Install the safety pin (1)(Ref.AMM TASK 25-62-00-860-801). T DIC 安装安全销(1)(Ref.AMM TASK 25-62-00-860-801)。4. On the PIM: 在PIM上：Push the key DOORS (3). 按压DOORS键(3)。On the PIM monitor (2) the related message:在PIM显示器(2)上显示以下相关信息：CHECK SLIDE PRESSURE: 1R or, CHECK SLIDE PRESSURE: 1L 或者CHECK SLIDE PRESSURE: 2R or, CHECK SLIDE PRESSURE: 2L 或者CHECK SLIDE PRESSURE: 4R is shown. CHECK SLIDE PRESSURE: 4L。* ON A/C CHH ALLON A/C CRK 001-300, 351-400ON A/C SIA ALL适用于CHH所有的飞机适用于手册有效号为CRK 001-300, 351-400的飞机适用于SIA所有的飞机Subtask25-62-41-710-053-BA. Do the operational test of the monitoring, through CIDS. 通过CIDS，进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Right Hand ) NOTE: Two persons are necessary to do the test. 注 释：必须至少两人执行这个测试。ACTION/操作 DIC T RESULT/结果1.At the Flight Attendant Panel (FAP) 120RH: 在飞行乘务面板120RH上：At the FAP 120RH: 在飞行乘务面板120RH上：- If the display screen is off, touch the screen surface.如果显示屏关闭，触摸一下屏幕表面。- The CABIN STATUS page comes on. 显示客舱模式CABIN STATUS页面。- Select the Doors/slides key (2).选择门/滑梯键（2）。- The DOORS/SLIDES page shows the related door (1R, 2R, 4R) amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门(1R, 2R, 4R)呈琥珀色显示，且显示信息SLIDE DISARMED 和CHECK SLIDE PESSURE。 DIC T 2.At the related door: 在相关门上：- Remove the safety pin (1) (Ref. AMM TASK 25-62-00-860-803) . 拆除安全销（1）(Ref.AMM TASK 25-62-00-860-803) 。 DIC T 3.At the FAP 120RH:在FAP 120RH面板上：- Select the Doors/Slides key (2). 选择Doors/Slids键（2）。- The DOORS/SLIDES page shows the related door (1R, 2R, 4R) amber, and the message SLIDE DISARMED. 在DOOR/SLIDES页面上相关门(1R, 2R, 4R)呈琥珀色显示，且显示信息SLIDE DISARMED。 DIC T 4.At the related door: 在相关门上：- Remove the PIN - SAFETY SLIDE (98A52107632000) (4) and set the emergency control-handle(3) to the ARMED position. 拆除安全销(98A52107632000)(4)，将紧急控制手柄(3)设置在ARMED位。WARNING: DO NOT OPEN THE DOOR WHEN THE EMERGENCY CONTROL-HANDLE IS SET IN THE ARMED POSITION.IF YOU DO, YOU WILL OPERATE THE ESCAPE-SLIDE RELEASE SYSTEM. THIS CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. DIC T 警 告：当紧急控制手柄在ARMED位时，不要打开门，否则，将释放紧急滑梯包，将可能 造成人员受伤或设备损坏。5.At the FAP 120RH: 在FAP 120RH面板上： - Select the Doors/Slides key (2). 选择DOOR/SLIDES键(2)。- The DOORS/SLIDES page shows the related door (1R, 2R, 4R) green, and the message SLIDE DISARMED goes off. DIC T 在DOOR/SLIDES页面上相关门(1R, 2R, 4R)呈绿色显示，且 显示的信息SLIDE DISARMED将消失。6.At the related door: 在相关门上：- Set the emergency control-handle to the DISARMED position and install the PIN-SAFETY SLIDE (98A52107632000) (4). 将紧急控制手柄设置在DISARMED位，并且安装安全销(98A52107632000)(4)。- Install the safety pin (1) (Ref. AMM TASK 25-62-00-860-801) . DIC T 安装安全销(1) (Ref.AMM TASK 25-62-00-860-801) 。7.At the FAP 120RH: 在FAP 120RH面板上：- Select the Doors/Slides key (2)选择Doors/Slides键(2)。- The DOORS/SLIDES page shows the related door (1R, 2R, 4R) amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门(1R, 2R, 4R)呈琥珀色显示，且显示信息SLIDE DISARMED和CHECK SLIDE PRESSURE。* ON A/C CRK 302-350 ON A/C HKC ALL 适用于手册有效号为CRK 302-350的飞机适用于HKC所有的飞机Subtask25-62-41-710-052-AA. Do the operational test of the monitoring, through CIDS. 通过CIDS，进行监测测试。(Ref/参考.Fig. Monitoring, through CIDS Right Hand)NOTE: Two persons are necessary to do the test. 注 释：必须至少两人执行这个测试。ACTION/操作 DIC T RESULT/结果1.At the Flight Attendant Panel (FAP) 120RH: 在飞行乘务面板120RH上：At the FAP 120RH: 在飞行乘务面板120RH上：- If the display screen is off, touch the screen surface.如果显示屏空白，触摸一下屏幕表面。- The CABIN STATUS page comes on. 显示客舱模式。- Select the Doors/slides key (2).选择门/滑梯键（2）。- The DOORS/SLIDES page shows the related door amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. DIC T 在DOOR/SLIDES页面上相关门呈琥珀色显示，且显示信息SLIDE DISARMED 和CHECK SLIDE PRESSURE。2.On the related door: 在相关门上：- Remove the safety pin (1) (Ref. AMM TASK 25-62-00-860-803) . 拆除安全销（1）(Ref.AMM TASK 25-62-00-860-803) 。 DIC T 3.At the FAP 120RH:在FAP 120RH面板上：- Select the Doors/Slides key (2). 选择Doors/Slides键（2）。- The DOORS/SLIDES page shows the related door amber, and the message SLIDE DISARMED. DIC T 在DOOR/SLIDES页面上相关门呈琥珀色显示，且显示信息SLIDE DISARMED。4.At the related door: 在相关门上：- Remove the PIN - SAFETY SLIDE (98A52107632000)(4) and set the emergency control-handle to the ARMED position. 拆除安全销(98A52107632000)(4)，将紧急控制手柄设置在ARMED位。WARNING: DO NOT OPEN THE DOOR WHEN THE EMERGENCY CONTROL-HANDLE IS SET IN THE ARMED POSITION.IF YOU DO, YOU WILL OPERATE THE ESCAPE-SLIDE RELEASE SYSTEM. THIS CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. DIC T 警 告：当紧急控制手柄在ARMED位时，不要打开门，否则，将释放紧急滑梯包，将可能造成人员受伤或设备损坏。5.At the FAP 120RH: 在FAP 120RH面板上：- Select the Doors/Slides key (2). 选择DOOR/SLIDES键(2)。- The DOORS/SLIDES page shows the related door green, and the message SLIDE DISARMED goes off. DIC T 在DOOR/SLIDES页面上相关门呈绿色显示，且 显示的信息SLIDE DISARMED将消失。6.On the related door: 在相关门上：- Set the emergency control-handle(3) to the DISARMED position and install the PIN - SAFETY SLIDE (98A52107632000)(4) . 设置应急控制手柄(3)至DISARMED并安装PIN - SAFETY SLIDE(98A52107632000)(4)。Install the safety pin(1) (Ref.AMMTASK25-62-00-860-801). 安装安全销（1）(Ref.AMMTASK25-62-00-860-801)。 DIC T 7.At the FAP 120RH: 在FAP 120RH面板上：- Select the Doors/Slides key (2).选择Doors/Slides键(2)。- The DOORS/SLIDES page shows the related door amber, and the messages SLIDE DISARMED and CHECK SLIDE PRESSURE. 在DOOR/SLIDES页面上相关门呈琥珀色显示，且显示信息SLIDE DISARMED和CHECK SLIDE PRESSURE。* ON A/C ALL 适用于所有飞机3. Close-up/工作结束A. Close Access T 关闭接近(1) Make sure that the work area is clean and clear of tools and other items. 确认工作区域干净，无工具和其它物品。(2) Arm the pack assembly (Ref. AMM TASK 25-62-00-860-803) . 预位滑梯包组件。(Ref. AMM TASK 25-62-00-860-803)。(3) Put the door back to a serviceable condition (Ref. AMM TASK 52-10-00-860-802) . 将门恢复至可用状态。(Ref. AMM TASK 52-10-00-860-802)(4) Remove the ground support and maintenance equipment, the special and standard toolsand all other items. 撤除地面支撑和维护设备，以及特殊和标准工具及其它物品。B.De-energize the aircraft electrical circuits (Ref.AMMTASK24-41-00-862-801). T 断开飞机电源(Ref.AMMTASK24-41-00-862-801)。AT-H25-62-41-001R HR001005 2018-01-25页码/Page8 / 16工卡Job card:HA33-25-LNME-050TITLEOperational Test of the Right Hand Escape-FacilitiesPerfIn