华为2326基础配置

华为S2326基础配置display device manuinfo display elabel华为查看设备编号display version查看设备型号、dis cu 查看当前配置从监控视图进入系统视图system-viewq 退出设置主机名称Quidwaysysname name设置console明文密码Quidwayuser-interface console 0 Quidway-ui-console0authentication-mode passwordQuidway-ui-console0set authentication password simple passwordQuidway-ui-console0user privilege level 3 设置用户级别，最高级别是3设置telnet 3级和2级用户huawei和manager分别为密文和明文密码Quidwayuser-interface vty 0 4Quidway-ui-vty0-4authentication-mode aaaQuidwayaaa必须进入aaa视图操作管理用户创建telnet 3级别huawei为密文密码Quidway-aaalocal-user huawei password cipher password 密码密文cipherQuidway-aaalocal-user huawei service-type telnet 登陆方式telnetQuidway-aaalocal-user huawei privilege level 3 最高用户级别3创建telnet 2级用户manager为明文密码Quidway-aaalocal-user manager password simple passwordQuidway-aaalocal-user manager service-type telnet Quidway-aaalocal-user manager privilege level 2 一般管理用户级别2设置交换机管理IPQuidwayinterface vlan 1Quidway-Vlanif1ip address 192.168.1.x 255.255.255.0Quidway-Vlanif1undo shutdown设置默认路由Quidwayip route-static 0.0.0.0 0.0.0.0 192.168.1.1设置SNMP协议Quidwaysnmp-agent community read public设置团体名Quidwaysnmp-agent sys-info version all 设置SNMP协议版本Quidwaysnmp-agent trap enable 开启系统自陷创建VLANQuidwayvlanvlan-id将交换机百兆1口加入VLANQuidway-Ethernet0/0/1port default vlan vlan-id设置交换机百兆1口限速为2MQuidwayinterface Ethernet 0/0/1Quidway-Ethernet0/0/1qos lr inbound cir 2048 cbs 流入流量用inboundQuidway-Ethernet0/0/1qos lr outbound cir 2048 cbs 流出流量用outbound端口分到端口组（通过对端口组的操作，实现对每个端口的操作）port group 2 定义端口分组2group-menber Ethernet 0/0/1 to Ethernet 0/0/24 将1到24端口分到端口组2保存当前配置saveThe current configuration will be written to the device.Are you sure to continue?Y/NyInfo: Please input the file name(*.cfg,*.zip)vrpcfg.zip:Now saving the current configuration to the slot 0 . 重启交换机rebootSystem will reboot! Continue?Y/N:y清空所有配置，还原默认设置reset saved-configurationThe configuration will be erased to reconfigure. Continue? Y/N:yreboot确定清空所有配置第一个选NWarning: All the configuration will be saved to the configuration file for the next startup:, Continue?Y/N:nSystem will reboot! Continue?Y/N:y华为 端口同时配置命令建立组port-group 1分配组内的端口（批量限速）group-member Ethernet 0/0/1 to Ethernet 0/0/24端口镜像（抓包使用）Observing-port 1 interface ethernet 0/0/1 (定义1口为观察口)Interface ethernet 0/0/2 (进入被镜像的2端口)Port-mirroring to observe-port 1 both （1口观察2口）both-双向流量 Inbound(进流量) out