WOHA33_5235319_153_AT-532100-220-854

Hong Kong Airlines LimitedHong Kong Air Cargo Carrier Limited香港航空有限公司香港货运航空有限公司F-D-099Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA335235_153_3195235319Training and Qualification/培训和资格Technical Record/技术记录NONENONETitleDETAILED INSPECTION OF FUSELAGE SKIN EXTERNAL SURFACE AT FRAMES FR 23 AND FR 24, BETWEEN STR 7 AND STR 10 RH.Mcd&Rev/厂家工卡&修订日期标题详细检查在隔框FR23和FR24处，在STR 7至STR10之间的机身蒙皮外表面，右侧AMM TASK 532100-220-8542018-05-01A/C/飞机号Subtask No/工卡号JC Rev/工卡版本号Workarea/工作区域Skill/工种Man Hour/工时BLNWAT-532100-220-854HR001000机身/AirframeAIRP00:21MP Item/MP号Baseline/依据MP REV/ MP版本号Station/维修站Threshold/首检Interval/重复检HA33-532018-02-1MPD 532018-02-1,ALI 532018-02-01ISS 3 REV 0PVG10400 CY,31300 FH5300 CY,Access Panels/接近盖板Zones/区域Written/编写Approved/批准NONE2002018-07-202018-07-20TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注1CML08BAA9Non Aqueous CleanerCH1ALL(视情/As Necessary)2CML14SBA1Textile_Lint free CottonCH1ALL(视情/As Necessary)IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HKE Approval No: AI /218/1215, JMM 133 * HNAT Approval No.: D.101115, JMM 047* CASL Approval No: AI / 101 / 798 * AMECO Approval No.: D.101131, JMM 001* HNAT- North West Approval No.: D.500023, JMM 049 * HAECO Approval No: DAI / 1 / 853 * SMECO Approval No.: D.400009, JMM 081* HNAT- YN Approval No.: D.4108, JMM 134 * TAECO Approval No.: DAI / 89 / 1295 * CEA Approval No.: D.200002, JMM 112 * HNAT Approval No.: D.3039, JMM 076 * THAECO Approval No.: D.101661, JMM 124 * CEA-Jiangsu Approval No.: D.200047, JMM 117 * SPRING Approval No.: D.200081, JMM 121 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: D.200078,JMM 039* GAMECO Approval No.: D.300001, JMM 006* THAI Approval No.: AI / 147 / 0910 * Other: *Signature:_ Authorization No.:_ Date:_AT-532100-220-854 HR001000 W/O:5235 AC:BLNW页码：2 / 6工卡Job card:HA33-532018-02-1TITLEDETAILED INSPECTION OF FUSELAGE SKIN EXTERNAL SURFACE AT FRAMES FR 23 AND FR 24, BETWEEN STR 7 AND STR 10 RH.PerfInsp标题详细检查在隔框FR23和FR24处，在STR 7至STR10之间的机身蒙皮外表面，右侧工作者检查者Detailed Inspection of Fuselage Skin External Surface at Frames FR 23 and FR 24, between STR 7 and STR 10 RH详细检查在隔框FR23和FR24处，在STR 7至STR10之间的机身蒙皮外表面，右侧WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURERS INSTRUCTIONS AND YOUR LOCAL REGULATIONS.警 告：小心使用消耗品，遵从材料厂家说明和当地规定。WARNING: WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A FALL CAN KILL OR INJURE YOU.警 告：当在高空作业时，佩戴并系上安全带。跌落会导致伤亡。1. Job Set-up/工作准备 A. Get Access/接近(1) Put the ACCESS PLATFORM 8M (26 FT) - ADJUSTABLE in position at the inspection area. M 在检查区域放置合适的工作梯在位 B. Preparation of the Inspection Area/检查区域的准备工作(1) Make sure that the surface of the inspection area is clean. M 确保检查区域的表面足够干净(2) If necessary, clean the inspection area with the Non Aqueous M Cleaner-General - -(MaterialNo. 08BAA9 ) and a lint-free cotton cloth Textile-Lint free Cotton -(MaterialNo.14SBA1 ) .按需使用清洁剂08BAA9和不起毛的抹布14SBA1清洁检查区域2. Procedure/步骤 (Ref.Fig.Inspection Area of Fuselage Skin External Surface at Frames FR23 and FR24, between STGR7 and STGR10 RHSHEET1)(参考Fig.Inspection Area of Fuselage Skin External Surface at Frames FR23 and FR24, between STGR7 and STGR10 RHSHEET1)A. Detailed Inspection Procedure/详细检查步骤 (1) Do the detailed inspection of fuselage skin external surface at frames FR23 and FR24, T between STGR7 and STGR10 RH.详细检查在隔框FR23和FR24处，在STR 7至STR10之间的机身蒙皮外表面，右侧(2) Make sure that there is no: T 确保无：(a) Corrosion damage: 腐蚀损伤： - If you find corrosion damage, refer to the Structural Repair Manual Ref. SRM512200 for types of corrosion, inspection, removal and corrosion protection. 若发现腐蚀，参考SRM512200确定腐蚀类型，检查方式，去除方法及腐蚀防护 Found Corrosion /发现腐蚀 Yes/是 No/否 Repair Document/修理文件号_(b) Other damage (scratches, cracks, gouges, dents, creases): 其他损伤（划伤，裂纹，沟槽，凹坑，褶皱）： - If you find this type of damage, refer to the Structural Repair Manual Ref. SRM511100 for damage classification and corrective action. 若发现这类型损伤，参考SRM511100确定损伤分类和修复工作 Found other damage /发现其他损伤 Yes/是 No/否 If found other damage,please record the damage type 若有其他损伤，请记录损伤类型_Repair Document/修理文件号_3. Close-up/结束工作 A. Close Access/结束接近(1) Make sure that the work area is clean and clear of tools and other items. M 确保工作区域干净，无工具和其他物品遗留(2) Remove the access platform(s). M 撤除工作梯AT-532100-220-854 HR001000 2018-07-20页码/Page4 / 6工卡Job card:HA33-532018-02-1TITLEDETAILED INSPECTION OF FUSELAGE SKIN EXTERNAL SURFACE AT FRAMES FR 23 AND FR 24, BETWEEN STR 7 AND STR 10 RH.PerfInsp标题详细检查在隔框FR23和FR2