11.27六综合实验

1、实验需求：在交换机上划vlan10，20，两个交换机配置vtp。将PC1，3划入vlan10。PC2，4划分vlan 20。R1单臂路由，R1R3配rip，R3（右）-R6配Ospf，在R3上重发布使两个协议兼容，a2a1建立虚链路，实现a2与a0(主干区域)相通。实现全互通。配置:I左交换机的配置：iterface FastEthernet0/1 switchport access vlan 10 switchport mode access!interface FastEthernet0/2 switchport access vlan 20 switchport mode access!

2、interface FastEthernet0/3 switchport mode trunk!interface FastEthernet0/4 switchport mode trunk全局模式：vtp mode serverVtp domain qqVtp version 1右交换机的配置：Vtp mode clientVtp domain qqVtp server 1（使此交换机学习到左交换机的vlan）iterface FastEthernet0/1switchport mode accessswitchport access vlan 10nterface FastEthernet

3、0/2 switchport access vlan 20 switchport mode accessinterface FastEthernet0/3 switchport mode trunkswitchport trunk allowe vlan allR1配置：interface Loopback0 ip address 1.1.1.1 255.255.255.0interface FastEthernet0/0 ip nat inside配置为内网接口!interface FastEthernet0/0.1 encapsulation dot1Q 10（承载来自vlan10的流量）

4、 ip address 192.168.1.14 255.255.255.240!ip对应pc1357的网关。interface FastEthernet0/0.2 encapsulation dot1Q 20 ip address 192.168.1.30 255.255.255.240ip对应pc2468的网关。interface FastEthernet0/1 ip address 202.1.1.10 255.255.255.0 ip nat outside（外部接口）配置PAT地址转换：access-list 1 permit anyip nat inside source list

5、 1 interface FastEthernet0/1 overload配置rip：router rip version 1 network 1.1.1.1 network 192.168.1.0 network 202.1.1.0R2配置：Interface lookback 0ip address 2.2.2.2 255.255.255.0 interface FastEthernet0/0 ip address 202.1.1.11 255.255.255.0!interface FastEthernet0/1 ip address 203.1.1.10 255.255.255.0!r

6、outer rip network 2.2.2.2 network 202.1.1.0 network 203.1.1.0R3的配置：interface Loopback0 ip address 3.3.3.3 255.255.255.0interface FastEthernet0/0 ip address 203.1.1.11 255.255.255.0interface FastEthernet0/1 ip address 204.1.1.10 255.255.255.0router ospf 100（配置ospf协议） router-id 3.3.3.3 redistribute ri

7、p subnets （重发布rip） network 3.3.3.3 0.0.0.0 area 0 network 204.1.1.0 0.0.0.255 area 0将3.3.3.3和204.1.1.10宣告到主干区域0.router rip redistribute ospf 100 metric 10 （重发布ospf） network 203.1.1.0配置重发布使rip与ospf两协议兼容。R4的配置：interface Loopback0 ip address 4.4.4.4 255.255.255.0 interface FastEthernet0/0 ip address 20

8、4.1.1.11 255.255.255.0interface FastEthernet0/1 ip address 205.1.1.10 255.255.255.0!router ospf 100 network 204.1.1.0 0.0.0.255 area 0 network 205.1.1.0 0.0.0.255 area 1 network 4.4.4.4 0.0.0.0 area 1将4.4.4.4和205.1.1.10宣告到区域1.area 1 virtual-link 5.5.5.5设置到区域2的虚链路，使区域2与0相通。R5的配置：interface Loopback0 i

9、p address 5.5.5.5 255.255.255.0interface FastEthernet0/0 ip address 205.1.1.10 255.255.255.0 interface FastEthernet0/1 ip address 206.1.1.10 255.255.255.0router ospf 100 area 1 virtual-link 4.4.4.4设置虚链路到a1。 network 205.1.1.0 0.0.0.255 area 1 network 206.1.1.0 0.0.0.255 area 2 network 5.5.5.5 0.0.0.0

10、 area 2将5.5.5.5 206.1.1.10宣告到区域2。R6的配置：interface Loopback0 ip address 6.6.6.6 255.255.255.0interface FastEthernet0/0 ip address 206.1.1.11 255.255.255.0 router ospf 100 log-adjacency-changes network 206.1.1.0 0.0.0.255 area 2 network 6.6.6.6 0.0.0.0 area 2PC的配置：将pc13的ip分别配置为：192.168.1.2 255.255.255.240 192