grasshopper翻译

1、Vector 改变Field 仿射ScaleX (Transform)-Transformation data-Scale an object uniformly in all directions.秤Input parameters:-在所有方向均匀地缩放对象。Input parameters:G (Geometry)-Base geometry-C (Point)输入参数：Center of scalingG（几何）F (Number)基本几何Scaling factorC（点）缩放中心Output parameters:F（数）G (Geometry)缩放系数Scaled geometr

2、y可编辑范本输出参数：G （几何）缩放几何X （变换）转换数据可编辑范本Scale NUX (Transform)-Transformation data-规模 NUScale an object with non-uniform factors.-Input parameters:缩放对象具有非均匀的因素。G (Geometry)-Base geometry-P (Plane)输入参数：Base planeG（几何）X (Number)基本几何Scaling factor in x directionP（平面）Y (Number)基面Scaling factor in y direction

3、X （编号）Z (Number)在 X 方向缩放系数Scaling factor in z directionY（数量）在 Y 方向缩放系数Output parameters:Z （数量）G (Geometry)在 Z 方向缩放系数Scaled geometry可编辑范本输出参数：X （变换）G （几何）转换数据缩放几何可编辑范本Shear剪断-剪切基于剪切向量的对象。Shear an object based on a shearing vector.-输入参数：-Input parameters:G（几何）G (Geometry)基本几何Base geometryP（平面）P (Plane

4、)基面Base planeG（点）G (Point)参照点Reference pointT （点）T (Point)目标点Target point输出参数：Output parameters:G（几何）G (Geometry)剪切几何Sheared geometryX （变换）X (Transform)变换的数据Transformatio data可编辑范本Shear Angle剪切角-Shear an object based on tilt angles.剪切根据倾斜角度的对象。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几

5、何P (Plane)P（平面）Base plane基面Ax (Number)AX （数）Rotation around x axis in radians左右旋转 X 轴弧度Ay (Number)唉（数）Rotation around y axis in radians弧度左右旋转Y 轴Output parameters:输出参数：G (Geometry)G（几何）Sheared geometry剪切几何X (Transform)X （变换）Transformation data转换数据可编辑范本Box MappingTransformation data-箱映射-Transformgeome

6、tryfromoneboxinto-从一个盒子形状变换成另一种。another.-输入参数：Input parameters:G（几何）G (Geometry)基本几何Base geometryS（盒）S (Box)然后就可以从图Box to map fromT （盒）T (Box)框映射成Box to map into输出参数：Output parameters:G（几何）G (Geometry)映射几何Mapped geometryX （变换）X (Transform)转换数据可编辑范本Orient DirectionG (Geometry)-Reoriented geometry-X (

7、Transform)Orientan object using directional constraintsTransformation dataonly.取向方向-Input parameters:取向只使用定向约束的对象。G (Geometry)Base geometry-pA (Point)-Reference point输入参数：dA (Vector)G（几何）Reference direction基本几何pB (Point)PA （点）Target point参照点dB (Vector)达（矢量）Target direction参考方向PB（点）Output parameters:

8、目标点可编辑范本分贝（向量）G（几何）目标方向重新定位几何X （变换）输出参数：转换数据可编辑范本Project工程-Project an object onto a plane.投射对象到一个平面上。-Input parameters:输入参数：G (Generic Data)G（通用数据）Geometry to project几何项目P (Plane)P（平面）Projection plane投影面Output parameters:输出参数：G (Generic Data)G（通用数据）Projected geometry投影几何X (Transform)X （变换）Transforma

9、tion data转换数据可编辑范本Project Along项目沿-Project an object onto a plane along a direction.投影到物体沿着一个方向的平面。-Input parameters:输入参数：G (Generic Data)G（通用数据）Geometry to project几何项目P (Plane)P（平面）Projection plane投影面D (Vector)D （矢量）Projection direction投影方向Output parameters:输出参数：G (Generic Data)G（通用数据）Projected geo

10、metry投影几何X (Transform)X （变换）Transformation data转换数据可编辑范本Rectangle Mapping矩形制图-Transformgeometry fromone rectangle into从一个矩形几何变换到另一个。another.-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何S (Rectangle)S（矩形）Rectangle to map from矩形从图T (Rectangle)T （矩形）Rectangle to map into矩形映射成Output paramete

11、rs:输出参数：G (Geometry)G（几何）Mapped geometry映射几何X (Transform)X （变换）Transformation data转换数据可编辑范本Triangle Mapping三角制图-Transformgeometry fromone triangle into从一个三角形几何变换到另一个。another.-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何S (Curve)S（曲线）Triangle to map from三角从地图T (Curve)T （曲线）Triangle to map

12、 into三角形映射到Output parameters:输出参数：G (Geometry)G（几何）Mapped geometry映射几何X (Transform)X （变换）Transformation data转换数据可编辑范本Array 排列Box ArrayArrayed geometry-X (Transform)-Transformation dataCreate a box array of geometry.长方体阵列-Input parameters:创建几何形状的长方体阵列。G (Geometry)-Base geometry-C (Box)输入参数：3D Box arr

13、ay cellG（几何）X (Integer)基本几何Number of elements in the array x-direction.C（盒）Y (Integer)3D 盒阵列单元Number of elements in the array y-direction.X （整数）Z (Integer)数组中元素的数目x 方向。Number of elements in the array z-direction.Y（整数）在该阵列y 方向元素的数目。Output parameters:Z （整数）G (Geometry)在数组 z 方向元件的数目。可编辑范本阵列式几何输出参数：X （变

14、换）G （几何）转换数据Curve Array曲线阵列-Create an array of geometry along a curve.创建几何沿曲线阵列。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何C (Curve)C（曲线）Array rail curve阵列轨道曲线N (Integer)N （整数）Number of elements in the array.数组中元素的数目。Output parameters:输出参数：G (Geometry)G（几何）Arrayed geometry阵列式几何X (Trans

15、form)X （变换）Transformation data转换数据可编辑范本Linear Array线阵-Create a linear array of geometry.创建几何图形的线性阵列。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何D (Vector)D （矢量）Linear array direction and interval线阵的方向和间隔N (Integer)N （整数）Number of elements in array.在数组元素的数量。Output parameters:输出参数：G (Geom

16、etry)G（几何）Arrayed geometry阵列式几何X (Transform)X （变换）Transformation data转换数据可编辑范本Polar ArrayTransformation data-极地阵列-Create a polar array of geometry.-创建几何极阵列。-Input parameters:-G (Geometry)输入参数：Base geometryG（几何）P (Plane)基本几何Polar array planeP（平面）N (Integer)极地阵列平面Number of elements in array.N （整数）A (N

17、umber)在数组元素的数量。Sweep angle in radians (counter-clockwise,一个号码）starting from plane x-axis)弧度后掠角（逆时针，从平面X 轴开始）Output parameters:G (Geometry)输出参数：Arrayed geometryG（几何）X (Transform)阵列式几何可编辑范本X （变换）转换数据可编辑范本Rectangular ArrayTransformation data-矩形阵列-Create a rectangular array of geometry.-创建几何图形的矩形阵列。-Inp

18、ut parameters:-G (Geometry)输入参数：Base geometryG（几何）C (Rectangle)基本几何Rectangular array cellC（矩形）X (Integer)矩形阵列单元Number of elements in the array x-direction.X （整数）Y (Integer)数组中元素的数目x 方向。Number of elements in the array y-direction.Y（整数）在该阵列y 方向元素的数目。Output parameters:G (Geometry)输出参数：Arrayed geometryG

19、（几何）X (Transform)阵列式几何可编辑范本X （变换）转换数据可编辑范本Kaleidoscope万花筒-Applya kaleidoscope transformationtoan应用万花筒改造的对象。object.-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何P (Plane)P（平面）Kaleidoscope plane万花筒飞机S (Integer)S（整数）Kaleidoscope segments.万花筒段。Output parameters:输出参数：G (Geometry)G（几何）Mirrored

20、geometry镜像几何X (Transform)X （变换）Transformation data转换数据可编辑范本Euclidean 几何变换Mirror镜像-Mirror an object.镜像的对象。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何P (Plane)P（平面）Mirror plane镜面Output parameters:输出参数：G (Geometry)G（几何）Mirrored geometry镜像几何X (Transform)X （变换）Transformation data转换数据可编辑范本Mo

21、ve移动-Translate (move) an object along a vector.平移（移动），以及矢量对象。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何T (Vector)T （矢量）Translation vector平移载体Output parameters:输出参数：G (Geometry)G（几何）Translated geometry平移几何X (Transform)X （变换）Transformation data平移数据可编辑范本Move Away From走出-Translate (move)

22、an object away from another平移（移动）一个对象远离另一个对象。object.-Input parameters:输入参数：G (Geometry)G（几何）Geometry to move几何移动E (Geometry)E（几何）Geometry to move away from几何从离开D (Number)D （数字）Distancetomove(negativevalues move距离移动（负值走向）towards)Output parameters:输出参数：G (Geometry)G（几何）Translated geometry平移几何X (Transf

23、orm)X （变换）Transformation data平移数据可编辑范本Move To PlaneTransformation data-移动到平面-Translate (move) an object onto a plane.-平移（移动）一个对象到一个平面上。-Input parameters:-G (Geometry)输入参数：Base geometryG（几何）P (Plane)基本几何Target planeP（平面）A (Boolean)目标平面Move when above planeA （布尔）B (Boolean)移动上述飞机上的时候Move when below pl

24、ane乙（布尔）移动以下平面时，Output parameters:G (Geometry)输出参数：Translated geometryG（几何）X (Transform)平移几何可编辑范本X （变换）平移数据可编辑范本Orient-Orient an object. Orientation is sometimes called a ChangeBasis tranformation. It allows for remapping of geometry from one axis-system to another.-Input parameters:G (Geometry) Bas

25、e geometry A (Plane) Initial planeB (Plane) Final planeOutput parameters:G (Geometry) Reoriented geometry X (Transform) Transformation data东方-定向一个对象。取向有时也被称为“ ChangeBasis tranformation。它允许重新映射几何从一个轴系统到另一个。-输入参数：G（几何）基本几何一架飞机）初始平面B（平面）最后面输出参数：G（几何）重新定位几何X （变换）平移数据可编辑范本Rotate旋转-Rotate an object in a p

26、lane.旋转的平面中的对象。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何A (Number)一个号码）Rotation angle in radians弧度旋转角度P (Plane)P（平面）Rotation plane旋转面Output parameters:输出参数：G (Geometry)G（几何）Rotated geometry旋转几何X (Transform)X （变换）Transformation data平移数据可编辑范本Rotate旋转-Rotate an object in a plane.旋转的平面中的对象。-Input parameters:输入参数：G (Geometry)G（几何）Base geometry基本几何C (Point)C（点）Rotation center point旋转中心点F (Vector)