吹瓶机基本知识051022VIP

1、吹瓶机基本知识2005.10.22目录:一. 吹瓶过程1. 吹瓶机 工艺流程图2. 机器操作步骤:11一. 吹瓶过程 1. 吹瓶机 工艺流程图吹瓶机示意图: 功能介绍表 (sidel)机器介绍 (krones)1. blow module2. heating module3. blowing station 4. blowing wheel, infeed/discharge starwheels5. infeed starweel6. mandrel chain7. control panel8. control cabinet9. water conditioning10. pneumat

2、ic components11. air conveyor12. heaters13. electrical14. air supply15. water supply, admission/return16. preform infeed rail17. preform unscrambler18. preform steep conveyor19. preform hopper20. preform dumper2. 机器操作步骤:上胚 瓶胚经过料斗, 上胚皮带, 被送到整理器的顶部, 经过整理, 成直线状排列, 进入上胚导轨. 经过入胚星轮, 瓶胚被送入加热炉的芯轴. 加热和平衡 经过加

3、热炉,瓶胚被加热到90-115c. 加热时, 可单独调节可调红外线光管的加热百分比. this is achieved with individually controllable infrared tubular radiators, arranged in nine levels.this array allows temperature variation on the preform. this temperature profile ensures the predefined material distribution, i.e., the bottle quality.to pr

4、event overheating, the exterior of the preform is cooled with fans.to prevent deformation, the sensitive neck-finish area is protected by a water-cooled shield. in addition, cooled air is also blown at the neck- finish area.the heating process takes approx. 20 seconds. afterward the preforms pass th

5、rough an equilibration zone for optimal distribution of the heat in the preform.then a starwheel transfers the preforms to the blowing stations.延伸-吹瓶过程: after the preform enters the blowing station, the base mould is raised, and the entire mould is closed and locked.the heated preforms are held and

6、fixed in place in the mould by means of the neck ring. this prevents deformation of the neck-finish.even while the mould is being closed, the blowing nozzle descends, the stretching rod moves toward the end cap for stretching, and after a brief delay the pre-blowing air flows in. the duration of the

7、 delay determines the thickness of the material in the bottle base.depending on the preform and bottle type, the pre-blowing pressure is 7-16 bar and lasts between 0.2-0.7 seconds, depending on the bottle size.at the end of the pre-blowing phase, the bottle is already fully shaped and material distr

8、ibution is finished.the final blowing phase now begins, producing the finest contours of the bottle and pressing the material against the cold mould (approx. 10c) for cooling.the higher the pressure, the better the cooling effect and the shorter the cooling time. the pressure ranges between 3040 bar

9、 and is maintained for approximately 2 seconds. afterward the stretching rod is retracted. before the mould is opened, the pressure in the bottle must be released.depending on the pressure and bottle size, this takes between 0.20.6 seconds and is baffled.after the bottle leaves the mould, it will sh

10、rink within 72 hours by 1%-2%.this process can be shortened by 515 minutes by preheating the mould (6070c).瓶子取出:the bottles are taken by the discharge starwheelthe bottles are transferred to the conveyor system.瓶胚和瓶子的机械手机械手 瓶胚机械手 the preforms are fed via a chute and steep belt conveyor to the top pa

11、rt of the unscrambler, where they are separated and then slide, with the neck-finish facing up, into the inclined infeed rail.after the infeed starwheel the preforms are transferred to the mandrels of the heating module.for optimal temperature distribution, the preforms revolve around their own axis, as they pass through the heating zone.after passing through the equilibration zone for optimal heat distribution in the preform, a starwheel transfers the preforms to the blowing station.瓶子机械手 after the blowing process the bottle i