模板-耳机咪头规格书4015和常见参数7页

1、 MICROPHONE SPECIFICATIONSPECIFICATION咪头规格书ELECTRET CONDENSER MICROPHONE型号：MODEL：4015L8-423-C1033一、 主要技术特性 Specifications1、灵敏度 Sensitivity: -42±3dB(0dB=1V/Pa,1KHz)2、指向性 Directivity: Omni-directional3、输出阻抗 Output Impedance: 2.2K±30% at 1KHz4、标准工作电压 Standard Operating Voltage: 2V5、工作电压 Opera

2、ting Voltage: 1.1V10V6、工作电流 Current Consumption: 350A7、信噪比 S/N Ratio: 60dB8、最大音压输入 Max Input Sound Level 115dB S.P.L9、频响曲线 Frequency Response Curve10、电路示意图 Schematic Circuit (Vs=4.5V RL=2.2K)10P 33P二、 机械性能 Mechanical Characteristics1.重 量 Weight : <0.3g2.外形尺寸 Dimensions: (Unit: mm)PartMin.Standard

3、Max.REMARKA3.9mm4.0mm4.1mmB1.4mm1.5mm1.6mmC/9mm10mm11/mmD/0.4mm0.5mm/0.6mmE/F0.1mm0.2mm0.3mmG/3.温度 TemperatureA) 储藏温度范围 Storage Temperature: -40+65B）使用温度范围 Operating temperature: -20+504.焊接热冲击 Soldering Heat Shock经过265±5焊接，灵敏度变化在±3dB变化范围内。After soldering heat shock at 265±5, sensitivi

4、ty change within ±3dB relative to initial value.三、可靠性试验 Reliability Test1.振动试验 Vibration Test在振动台上，话筒经过三个方向的振动，振幅1.52mm，振动频率由10Hz到50Hz循环，每分钟一次，振动2小时，其灵敏度变化在+3dB范围内。After Vibration cycle of 10 to 50Hz/1min, for 2 hours, full Amplitude 1.52mm,in 3 directions, Sensitivity change within ±3dB r

5、elative to initial value.2.跌落试验 Dropping Test将试验话筒装入包装盒内，分三个不同的侧面，每次从1米高度跌落在地板上，其灵敏度变化在±3dB之内。With package ,dropping to concrete floor 1m height in the directions of three different edges, sensitivity change within ±3dB relative to initial value.3.温度试验 Temperature TestA)高温试验 High Temperatu

6、re Test将测试话筒放在+80±2的烘箱内，经过200小时，在20室温内放置2小时之后测量，其灵敏度变化在±3dB之内。After exposure at +80±2 for 200 hours, and recovering in 20 for 2 hours ,sensitivity change within ±3dB relative to initial value.B)低温试验 Low Temperature Test将试验话筒放在-25±2的低温箱内，经过200小时，在20室温内放置2小时之后测量，其灵敏度变化在±3

7、dB之内。After exposure at-25±2 for 200 hours, and recovering in 20 for 2 hours, sensitivity change within ±3dB relative to initial value. 4.潮湿试验 Humidity Test将话筒放置在+60±2和相对湿度在90±5的潮湿箱内200小时，取出后防在20室温内2小时之后测试，灵敏度变化在±3dB之内。After exposure at +60±2 and relative humidity 90

8、7;5 for 200 hours, and recovering in 20 for 2 hours , sensitivity change within± 3dB relative to initial value. 5.温循试验 Temperature Cycle Test将试验话筒放在-55±2的低温箱内30分钟，取出在室温20内10分钟自然恢复后，放入温度为+85±2的烘箱内30分钟，取出放在室温20内10分钟，此为一个温循过程。经过5次循环，在室温20自然恢复2小时后测试，其灵敏度变化在±3dB之内。After exposure at 5

9、times of the following cycles, and recovering in 20 for 2 hours, Sensitivity change within 3dB relative to initial value.+20+20+85±2-55±230m30m10m10m一个周期 one Cycle 四、 结构图 Microphone Material TableNOPARTSMODELMANUFACTURER1线路板 PCBSuZhou SanSheng 2场效应管 FET2023电容 CapacitorMURATA4塑环 Holder SuZh

10、ou WorlD5铜环 Connecter SuZhou WorlD6振膜 MembraneDUPONT USA7垫片 SpacerWangSunZhuang HeBei8极板 PlateSuZhou WorlD9外壳 Outer most shellLansen Electronic Corp Shanghai10防尘网 Protection fleeceChangzhou ChaoQi11连接线 WireUL1571 32#关于焊接操作Regarding the soldering operation每个驻极体传声器中都有一个场效应晶体管，半导体很容易在过热电压过高而受到损害。Each C

11、on. Mic. contains a FET within its case. Generally, semiconductors are easily weakened by over-heating, over-charge of voltage.正常焊接的注意事项：Special caution is needed for proper soldering as follows:1.用15W-20W控温烙铁，温度控制在260-280进行焊接。Use 15W-20W soldering iron and maintain 260-280 in operation.2.焊接时间在每个焊点上控制在2秒钟以内，不允许时间过长。Soldering should be accomplished within two seconds at each terminal so as not to be overheated.3.焊接时间过长，或焊接温度过高，不但会引起场效应管发生变化，并