加工中心的编程

1、正弦曲线72.120一.加工工艺1.钻孔用9.8的钻头T12.较孔用10的餃刀T23.扩孔用eil.7的钻头T34.铳孔用12的立铳刀T45.铳正弦曲线用12的立铳刀T46.铳内腔用12的立铳刀T47.排料用12的立铳刀T48.换面铳凹槽用12的立铳刀T4二.刀具的选择在加工工序中采用了用12的立铳刀、P11.7的钻头、10的较刀、9.8的钻头。三.切削参数加工内容刀号刀具类型主轴转速进给速度刀具补偿1.钻孔T1用09.8的钻头500602.较刀T2用10的较刀200603.扩孔T3用11.7的钻头500604. 铳孔T45. 铳正弦曲线T46. 铳内腔T47. 排料T48. 换面铳凹键槽T4

2、四.参考程序%1 （钻孔）G54G00X0Y0Z10M07M03S500G81G98X0Y0Z-3 8R3F60X-50Y25X50Y25 X-32.5Y15Z-9.85G00Z100M09M05M30%1 （较孔）G54G00X50Y25Z10M07M03S500G85G98X50Y25Z-38R3F60X-50Y25G00Z100M09M05M30%1 （扩孔）G54G00X0Y0Z10M07M03S500G81G98X0Y0Z-3 8R3F60X-32.5Y15Z-9.85G00Z100M09M0510001000D011000100D011000100D0110001001000100

3、D01用12的立铳刀 用12的立铳刀 用12的立铳刀 用12的立铳刀用12的立铳刀%1 （铳孔）G54G00X0Y0Z10M03S1000M07#1=0#2=32WHILE#1GE 存 2G01Z#lF1000G41G01X12Y0D01G03I-12J0G40G01X0Y0#1=#1-0.1ENDWG00Z100M09M05M30%1 （正弦曲线）G54G00X70Y70Z10M07M03S1000#1=0#2=-10WHILE#1GE 存 2G01Z#lF100G41G01X50Y50D01M98P2G40G00X70Y70#1=#1-2.5ENDWG00Z10X-70Y70#11=0#1

4、2=-10WHILE #11 GE# 12M30GO1Z#1F1OOG41G01Y-25*SQRT3-G41G01X-50Y50D01SQRT65*65-32.5*32.5-24 DOIM98P3G01Y-29G40G00X-70Y70G03X-22.5W39R10# 11=#11-2.5G01X22.5ENDWG03X32.5Y-29R10G00Z100G01Y-25*SQRT3J-M09SQRT65*65-32.5*32.5-24M05G03X32.5YSQRT65*65-32.5*32.5-24R25M30X-32.5Y SQRT65*65-32.5*32.5-24R65X-32.5Y-

5、25*SQRT3-%2SQRT65*65-32.5*32.5-24R25#1=50G01Y-29#2=0XH* SQRT3Y-20WHILE#1GE 卜 50G01X-12* SQRT3Y4#2=#2+360/1000G02X-8* SQRT3Y16R8#3=10*SIN#2*PI/180G01X8* SQRT3G01X#3Y#lG02X12* SQRT3Y4R8G01X4* SQRT3Y-20ENDWG02X-4* SQRT3Y20R8G01X80Y-70G01X-12* SQRT3Y4M99G40G01X-32.5Y15%3ENDW#1=50#2=0G00Z100WHILE#1GE 卜 50%1 （换面加工凹键槽）#2=#2-360/1000G54#3=10*SIN#2*PI/180G00X0Y0Z10G01X#3Y#l£20M07ENDWM03S1000G01X-80Y-70#1=0M99#2=-10WHILE#1 GE 存 2%1 （铳内腔）GO1Z#1F1OOG54G42G01X-36Y0 DOIG00X-32.5Y15Z10G02X26Y10R10M07GO 1X26M03S1000G02X36Y0R10#1=0G40G01X0Y-20#2=-10#l=#l-2.5WHILE