everest0.6 安装 HuaWei ET128 3G上网卡课件

1、前天去移动办了个随e行G3上网卡，回来一看，只有windows驱动和软件，但我平时多数时间在linux下，用google扒啦了一下，还真有配置方法，现简化一下，共享之上网卡型号：HUAWEI ET128系统版本：Qomo 0.6 GCC44 （-40）1、首先下载安装usb_modeswitch：#wget http:/www.draisberghof.de/usb_modeswitch/usb_modeswitch-1.0.2.tar.bz2解压，编译安装：#tar xjvf usb_modeswitch-1.0.2.tar.bz2#cd usb_modeswitch-1.0

2、.2#make install然后编辑usb_modeswitch.conf配置文件：#vi /etc/usb_modeswitch.conf该配置文件内有世面上绝大多数的无线上网卡配置信息，但没有华为ET128硬件的相关信息(可能比较新吧)，需要手工添加如下内容进去# Huawei ET128# Contributor: Dale LaneDefaultVendor= 0x12d1;DefaultProduct= 0x1da1# choose one of these:DetachStorageOnly=0HuaweiMode=1#其中注意红色部分，是厂商信息和硬件信息，可以通过lsusb命

3、令查看获取：#lsusbBus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubBus 004 Device 002: ID 0b05:b700 ASUSTek Computer, Inc.Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 002 Device 002: ID 04fc:0003 Sunplus Techno

4、logy Co., Ltd CM1092 Optical Scroller MouseBus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 001 Device 012: ID 12d1:1da1 Huawei Technologies Co., Ltd.Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub2、配置完成后，执行usb_modeswitch -W命令创建tty设备# usb_modeswitch -W再查看dmesg信息，如果有生成

5、新的ttyACMx设备即表示成功#dmesgcdc_acm 1-2:3.1: ttyACM0: USB ACM devicecdc_acm 1-2:3.3: ttyACM1: USB ACM devicecdc_acm 1-2:3.5: ttyACM2: USB ACM device3、安装wvdail拨号工具，源里有（据说可以在NetworkManager下使用，但我没配置成功，望达人指教）#yum install wvdial执行wvdialconf扫描硬件并生成配置文件：#wvdialconf编辑/etc/wvdial.conf配置文件加入如下拨号配置信息：;#Phone = *99*1

6、#Password = anyUsername = anyStupid Mode = 14、拨号：#wvdial-> Ignoring malformed input line: "#"-> WvDial: Internet dialer version 1.60-> Cannot get information for serial port.-> Initializing modem.-> Sending: ATZATZOK-> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0ATQ

7、0 V1 E1 S0=0 &C1 &D2 +FCLASS=0OK-> Modem initialized.-> Sending: ATDT*99*1#-> Waiting for carrier.ATDT*99*1#CONNECT 2800000-> Carrier detected. Starting PPP immediately.-> Starting pppd at Mon Jul 27 16:31:44 2009-> Pid of pppd: 3667-> Using interface ppp0-> pppd: ?06

8、0810?0608-> pppd: ?060810?0608-> pppd: ?060810?0608-> pppd: ?060810?0608-> pppd: ?060810?0608-> local IP address 8-> pppd: ?060810?0608-> remote IP address 1-> pppd: ?060810?0608-> primary   DNS address 0-> pppd: ?060810?0608-

9、> secondary DNS address 2-> pppd: ?060810?0608OK,冲浪去吧，关闭只需crtl + c想方便可以写个脚本放到桌面：#!/bin/sh/usr/sbin/usb_modeswitch -Wsleep 5echo "nameserver 0" >/etc/resolv.conkonsole -e /usr/bin/wvdial每次插上U盘，然后双击该脚本，断线时按ctrl + c即可Ubuntu 9.04 安装 HuaWei ET128 3G上网卡1. 把HuaWei

10、3G上网卡insert到电脑的USB port.#dmesg | grep HUAWEI 4411.960220 scsi 10:0:0:0: CD-ROM HUAWEI Mobile CMCC CD 1.25 PQ: 0 ANSI: 0# lsusb | grep HuaweiBus 005 Device 007: ID 12d1:1d09 Huawei Technologies Co., Ltd.这里需要记下ID 后面的.2.下载安装usb_modeswitch .下载地址:http:/www.draisberghof.de/usb_modeswitch安装请看软件的README文件.拷贝

11、编译完的usb_modeswitch 到/sbin下#usb_modeswitch -h 查看使用方法#usb_modeswitch -W 最好执行一下,查看一下设置 print all settings before running3.需要修改 /etc/wvdial.conf 配置文件.Please see my config file:Dialer DefaultsInit1 = ATZInit2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Modem Type = USB ModemBaud = 460800;Baud = 9216000New

12、 PPPD = yesModem = /dev/ttyACM2 #这里我是安装了gnome-ppp自动识别出来的;Modem = /dev/ttyUSB0ISDN = 0; Phone = <Target Phone Number> Password = <Your Password> Username = <Your Login Name>Phone = *99*1#Password = anyUsername = anyStupid Mode = 14.拔号sudo wvdial可能需要等一会，你会看到heqiangheqiang-laptop:$ su

13、do wvdial-> WvDial: Internet dialer version 1.60-> Cannot get information for serial port.-> Initializing modem.-> Sending: ATZATZOK-> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0OK-> Modem initialized.-> Sending: ATDT*99*1#-> Wa

14、iting for carrier.ATDT*99*1#CONNECT 236800-> Carrier detected. Starting PPP immediately.-> Starting pppd at Thu Jun 11 14:17:31 2009-> Pid of pppd: 19674-> Using interface ppp0-> pppd: P)J08)J08-> pppd: P)J08)J08-> pppd: P)J08)J08-> pppd: P)J08)J08-> pppd: P)J08)J08-> p

15、ppd: P)J08)J08-> pppd: P)J08)J08-> local IP address 4-> pppd: P)J08)J08-> remote IP address 1-> pppd: P)J08)J08-> primary DNS address 2-> pppd: P)J08)J08-> secondary DNS address 0-> pppd: P)J08)J08说明连接成功了!$sudo ifconfig ppp0ppp

16、0 Link encap:点对点协议 inet 地址:4 点对点:1 掩码:55UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 跃点数:1接收数据包:18798 错误:0 丢弃:0 过载:0 帧数:0发送数据包:14731 错误:0 丢弃:0 过载:0 载波:0碰撞:0 发送队列长度:3接收字节:23233292 (23.2 MB) 发送字节:1357737 (1.3 MB)5.这里写的比较单，相信你能成功.不行的话，下面的希望有用：一开始插上3G卡的时候，lsusb显示为：u

17、buntuUbuntu:$ lsusb | grep HuaweiBus 002 Device 002: ID 12d1:1da1 Huawei Technologies Co., Ltd. 这时候，修改/etc/usb_modeswitch.conf：DefaultVendor= 0x12d1DefaultProduct= 0x1da1TargetVendor= 0x12d1TargetProduct= 0x1da1HuaweiMode=1执行sudo usb_modeswitch -W 令修改生效。这时候ubuntuUbuntu:$ lsusb | grep HuaweiBus 002 D

18、evice 002: ID 12d1:1d09 Huawei Technologies Co., Ltd. 会发现1da1变成了1d09. 然后再修改/etc/usb_modeswitch.confDefaultVendor= 0x12d1DefaultProduct= 0x1d09TargetVendor= 0x12d1TargetProduct= 0x1d09;HuaweiMode=1再执行sudo usb_modeswitch -W令修改生效。检查/dev/下面， 会出来ttyACM0, ttyACM1, 和ttyACM2.然后再执行sudo wvdialconf自动生成配置文件ubun

19、tuUbuntu:$ sudo wvdialconf Editing /etc/wvdial.conf'.Scanning your serial ports for a modem.Modem Port Scan<*1>: S0 S1 S2 S3 WvModem<*1>: Cannot get information for serial port.ttyACM0<*1>: ATQ0 V1 E1 - OKttyACM0<*1>: ATQ0 V1 E1 Z - OKttyACM0<*1>: ATQ0 V1 E1 S0=0 -

20、OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 - OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 - OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 - OKttyACM0<*1>: Modem Identifier: ATI - Manufacturer: HuaWeittyACM0<*1>: Speed 4800: AT - OKttyACM0<*1>: Speed 9600:

21、 AT - OKttyACM0<*1>: Speed 19200: AT - OKttyACM0<*1>: Speed 38400: AT - OKttyACM0<*1>: Speed 57600: AT - OKttyACM0<*1>: Speed 115200: AT - OKttyACM0<*1>: Speed 230400: AT - OKttyACM0<*1>: Speed 460800: AT - OKttyACM0<*1>: Max speed is 460800; that should be

22、safe.ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 - OKWvModem<*1>: Cannot get information for serial port.ttyACM1<*1>: ATQ0 V1 E1 - OKttyACM1<*1>: ATQ0 V1 E1 Z - OKttyACM1<*1>: ATQ0 V1 E1 S0=0 - OKttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 - OKttyACM1<*1>

23、;: ATQ0 V1 E1 S0=0 &C1 &D2 - OKttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 - OKttyACM1<*1>: Modem Identifier: ATI - Manufacturer: HuaWeittyACM1<*1>: Speed 4800: AT - OKttyACM1<*1>: Speed 9600: AT - OKttyACM1<*1>: Speed 19200: AT - OKttyACM1<*1>:

24、 Speed 38400: AT - OKttyACM1<*1>: Speed 57600: AT - OKttyACM1<*1>: Speed 115200: AT - OKttyACM1<*1>: Speed 230400: AT - OKttyACM1<*1>: Speed 460800: AT - OKttyACM1<*1>: Max speed is 460800; that should be safe.ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0

25、 - OKWvModem<*1>: Cannot get information for serial port.ttyACM2<*1>: ATQ0 V1 E1 - OKttyACM2<*1>: ATQ0 V1 E1 Z - OKttyACM2<*1>: ATQ0 V1 E1 S0=0 - OKttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 - OKttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 - OKttyACM2<*1>: ATQ0 V1

26、 E1 S0=0 &C1 &D2 +FCLASS=0 - OKttyACM2<*1>: Modem Identifier: ATI - Manufacturer: HuaWeittyACM2<*1>: Speed 4800: AT - OKttyACM2<*1>: Speed 9600: AT - OKttyACM2<*1>: Speed 19200: AT - OKttyACM2<*1>: Speed 38400: AT - OKttyACM2<*1>: Speed 57600: AT - OKttyAC

27、M2<*1>: Speed 115200: AT - OKttyACM2<*1>: Speed 230400: AT - OKttyACM2<*1>: Speed 460800: AT - OKttyACM2<*1>: Max speed is 460800; that should be safe.ttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 - OKFound an USB modem on /dev/ttyACM0.Modem configuration writt

28、en to /etc/wvdial.conf.ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"ttyACM1<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"ttyACM2<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0&quo

29、t;ubuntuUbuntu:$ 再修改/etc/wvdial.conf中的相应部分就可以了。我的配置如下：Dialer DefaultsInit1 = ATZInit2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Password = anyPhone = *99*1#Modem Type = USB ModemStupid Mode = 1Baud = 460800New PPPD = yesModem = /dev/ttyACM0ISDN = 0username = any; Phone = <Target Phone Number>

30、 Password = <Your Password> Username = <Your Login Name>之后，就知道该怎么做了吧？ sudo wvdial就OK了。ubuntuUbuntu:$ sudo wvdial-> WvDial: Internet dialer version 1.60-> Cannot get information for serial port.-> Initializing modem.-> Sending: ATZATZOK-> Sending: ATQ0 V1 E1 S0=0 &C1 &a

31、mp;D2 +FCLASS=0ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0OK-> Modem initialized.-> Sending: ATDT*99*1#-> Waiting for carrier.ATDT*99*1#CONNECT 2800000-> Carrier detected. Starting PPP immediately.-> Starting pppd at Mon Jun 22 11:11:50 2009-> Pid of pppd: 4134-> Using interface p

32、pp0-> local IP address 11-> remote IP address 1-> primary DNS address 0-> secondary DNS address 2OK了！Fedora 10 安装 HuaWei ET128 3G上网卡上网卡型号：HUAWEI ET128系统版本： Fedora 101、首先下载安装usb_modeswitch：#wget http:/www.draisberghof.de/usb_modeswitch/usb_mo

33、deswitch-1.0.2.tar.bz2解压，编译安装：#tar xjvf usb_modeswitch-1.0.2.tar.bz2#cd usb_modeswitch-1.0.2#make install然后编辑usb_modeswitch.conf配置文件：#vi /etc/usb_modeswitch.conf该配置文件内有世面上绝大多数的无线上网卡配置信息，但没有华为ET128硬件的相关信息(可能比较新吧)，需要手工添加如下内容进去# Huawei ET128# Contributor: Dale LaneDefaultVendor= 0x12d1 DefaultProduct=

34、0x1da1     (这个要根据lsusb的输出更改)# choose one of these:DetachStorageOnly=0HuaweiMode=1#其中注意红色部分，是厂商信息和硬件信息，可以通过lsusb命令查看获取：#lsusbBus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubBus 004 Device 002: ID 0b05:b700 ASUSTek Computer, Inc.Bus 004 Device 001: ID 1d6b:0001 Linux

35、Foundation 1.1 root hubBus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 002 Device 002: ID 04fc:0003 Sunplus Technology Co., Ltd CM1092 Optical Scroller MouseBus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 001 Device 012: ID 12d1:1da1 Huawei Technologies Co., Ltd.B

36、us 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub2、配置完成后，执行usb_modeswitch -W命令创建tty设备# usb_modeswitch -W再查看dmesg信息，如果有生成新的ttyACMx 设备即表示成功#dmesgcdc_acm 1-2:3.1: ttyACM0 : USB ACM devicecdc_acm 1-2:3.3: ttyACM1 : USB ACM devicecdc_acm 1-2:3.5: ttyACM2 : USB ACM device3、安装wvdail拨号工具，源里有（据说可以在NetworkManager下使用，但我没