I5800开局配置(包括qinq,修改数据后可复制粘贴))20130506

1、*以下可直接复制：*#节点下：user name xxxx password xxxxxx user name xxxx privilege 15 enable password配置SNMP: Raisecom(config)# snmp-server community dgpbs ro snmp-server host172.20.6.9 version 2c dgpbs udpport 162 snmp-server host 172.20.6.2 version 2c dgpbsudpport 1621、创建板卡(需要先安装好)：(fttx)#节点下：create card slot

2、1 type 4pon create card slot 2 type 4pon create card slot 3 type 4poncreate card slot 4 type 4pon create card slot 5 type 4pon create card slot 6 type 4gecreate card slot 9 type 4pon create card slot 10 type 4pon create card slot 11 type 4pon2、隔离端口，slot 1表示第一槽，类推：Raisecom(fttx)#节点下：slot 1port-isolat

3、ion enable port-list 1-4 exitslot 2 port-isolation enable port-list 1-4 exitslot 3 port-isolation enable port-list 1-4 exitslot 4 port-isolation enable port-list 1-4 exitexit*另，如下配置需要进入config或相关的节点，按实际情况修改，不可直接复制doc文档：*3、创建VLAN及设IP:Raisecom(c on fig)#节点下：conf tcreate vlan 151,1450-1459 activeinterfa

4、ce ip 1ip address 10.163.151.17 255.255.255.0 151exitRaisecom(c on fig)#节点下配网关：ip default-gateway 10.163.151.254配上联捆绑口(旧型号的I5800为11-14口)：interface port 25swi mo trunkswitchport trunk allowed vlan 151,1450-1459exitinterface port 26swi mo trunkswitchport trunk allowed vlan 151,1450-1459exitinterface p

5、ort 27swi mo trunkswitchport trunk allowed vlan 151,1450-1459exitinterface port 28swi mo trunkswitchport trunk allowed vlan 151,1450-1459exittrunk group 12 port 25,26,27,28 lacp-static25-28捆绑为trunk口，同时启用lacp，交换机也要启用lacp。exitinterface range 25，26，27，28，命令作用见switchport trunk allowed vlan 151，1450-1459

6、/将25-28口捆绑并放通vlan 151,1450-1459(接1080要进入端口，强制 为1000/full)4、业务板上联口配置/新型号的i5800E每一个epon口对应独立的千兆上联口， 由于旧epon口的性能有限， 用 旧的epon板时仍是一个epon板对应2个上联千兆口,可在#下用命令show port-map查看epon口与虚拟上联口的对应关系：Raisecom(c on fig)#节点下：conf tinterface range 1,2switchport mode trunkexitinterface range 5,6switchport mode trunkexitin

7、terface range 9,10switchport mode trunkexitinterface range 13,14switchport mode trunkexitinterface range 17,18switchport mode trunkexitinterface range 21,22switchport mode trunkexit以下为将槽位里的4个epon口配为trunk口，aisecom(fttx-slot:1)#节点下：fttxslot 1vlan mode trunk port-list 1-4exitslot 2vlan mode trunk port-

8、list 1-4exitslot 3vlan mode trunk port-list 1-4exitslot 4vlan mode trunk port-list 1-4 exit fttx slot 5vlan mode trunk port-list 1-4 exitslot 9vlan mode trunk port-list 1-4exitslot 10vlan mode trunk port-list 1-4exitslot 11vlan mode trunk port-list 1-4 exit以下为将每一个epon口设置为手动注册Raisecom#fttx interface

9、range olt 1/1-4 authorization mode mac exitinterface range olt 2/1-4 authorization mode mac exitinterface range olt 3/1-4 authorization mode mac exitinterface range olt 4/1-4 authorization mode mac exitinterface range olt 5/1-4 authorization mode mac exitinterface range olt 9/1-4 authorization mode

10、mac exitinterface range olt 10/1-4 authorization mode mac exitinterface range olt 11/1-4 authorization mode macexit exit*5、配置qinq（这里以第一槽为例，其它槽位类推）:*fttx create onu-config-template 1 name bind create onu-config-template 2 name app exit fttxonu-config-template 1 native vlan 101 140 exit exit/以上为配qinq下

11、发小vlan的模板；conf inter range 1,2 no sw trunk allow vlan switchport mode trunk no switchport trunk native vlan sw trunkallow vlan 1451 con switchport protect switchport qinq dot1q-tunnel switchport vlan-mapping cvlan101-140 add-outer 1451 switchport trunk untagged vlan 1451 con exit exit fttx/以上为在epon板的上联口放通vlanslot 1no vlan access port-list all vlan mode trunk port-list all port-isolation enable port-list 1-4 vlan trunk allowedadd 101-140,1450 port-list 1-4 exit interface range olt 1/1-4 onu-config-template 1 binded