FPC0性能规格书

1、TPG ELECTRONICS COMPANY LIMITEDTPG PITCH FPC CONNECTOR1. 适用范围SCOPE本规格书适用于FPC CONNECTOR列This specification covers the CONNECTOR .2. 产品编号 ORDERING INFORMATIONPART NO.:F CL -* EN12341.系列名称Series n ameCONNECTOR2.组合样式C5 UPPER CONTACTS 接触Assembly styleC6 LOWER CONTACT 接触3.接点数量Number of con tacts4-504.电镀方式

2、EN: LEAD FREEPlat ingG: Gold over Nickel3. 夕卜观尺寸 CONNECTOR DIMENSIONS请参照图面.See attached drawings4. 材质 MATERIAL绝缘胶体 Housi ng : NY-9T耐燃等级(UL94V-0) Flammability rati ng (UL94V-0 ) 耐温265 C导电端子 Con tacts:磷青铜 Phosphor Bronze5. 等级 RATING项目ITEM规格Sta ndard额定电压Voltage rat ing50V AC,DC额定电流Curre nt rat ing0.5A

3、AC,DC储存条件Storage con diti ons温度 Temperature0°C +28 C相对湿度 Relative humidity 40%60%温度范围Temperature range-25 C+85C (包含电流通过所产生的上升温度)-25 C + 85C (Including temperature rise inappl ying electrical curre nt)TPG ELECTRONICS COMPANY LIMITEDTPG PITCH FPC CONNECTOR6. 1 性能 PERFORMANCE项目ITEM测试条件TEST CONDITI

4、ON规格PEQUIRMENT电气特性ELECTRICAL PERFORMANCE接触阻抗Con tact Resista nee将样品与适合之FPC连接,测试电压20mV,限电流 10mAT进行阻抗测试.Mate applicable FPCand measure by dry circuit, 20mV Max, 10mA40mQ以下40mQ Max绝缘阻抗In sulati onResista nee将样品与适合之FPC连接,提供相邻端子间测试电压 500V DC进行绝缘阻抗测试.Mate 即 plicable FPC and apply 500V DC betwee n adjace n

5、t term inal or ground500MQ以上500MQ Min耐电压Withsta nding voltage将样品与适合之FPC连接,相邻端子间可承受500VAC/1分钟.Mate ap plicable FPC , apply 500V AC/ 1mi nute betwee n adjace nt term inal or ground.目视外观无任何损 坏异状No Breakdow n机械特性MECHANICAL PERFORMANCEFPC保持力FPC Retention Force与FPC连接,以操作速度每分钟位移 25±3 mm进行 FPC保持力测试.Ins

6、ert the connector , Pull the FPC at a rate of 25±3 mm per minutepin 以上pin Min端子保持力Terminal Rete nti onForce端子与Housing组装后,以操作速度每分钟位移 25±3mn将端子拔出Housing,进行端子保持力测试Apply axial pull out force at the rate of 25±3mm per minute on the term inal assembled in the hous ing.pin 以上pin MinTPG ELECT

7、RONICS COMPANY LIMITEDTPG PITCH FPC CONNECTOR性能 PERFORMANCE项目ITEM测试条件TEST CONDITION规格PEQUIRMENT环境特性及其它性能ENVIRONMENTAL PERFORMANCE AND OTHERS耐热性Heat Resista nee将样品与适合FPC连接,置于环境温度85土 2C测试 时间96小时,再置放于室温下12小时.Mate applicable FPC and expose to 85± 2 °C for96 hour. Uponeompletion of the exposure

8、 period, the test speeimens shall be conditionedatambient room eonditions for 1 to 2 hours, after whieh the speeifiedmeasurements shallbeperformed.目视外观无任何损坏异状No Damage接触阻抗60mQ以下Con taet Resista nee60mQ MAX耐寒性Cold Resista nee将样品与适合FPC连接,置于环境温度-25 ± 2C测试 时间96小时,再置放于室温下12小时.Mate applieable FPC and

9、 expose to -25± 2C for96 hour. Uponeompletion of the exposure period, the test speeimens shall be eonditionedatambient room eonditions for 1 to 2 hours, after whieh the speeifiedmeasurements shallbeperformed目视外观无任何损 坏异状No Damage接触阻抗60mQ以下Con taet Resista nee60mQ MAX冷热冲击Temperature Cyeli ng将样品与适

10、合之FPC连接,承受5 Cyeles冷热冲击 后,置放于室温下下12小时.1 Cyele time 如下a> -2 5± 2C 30 分钟b> 85 ± 2C 30 分钟Mate applieable FPCand subjeet to the following eonditions for 5 eyeles. Upon eompletion of the exposure period, the test speeime ns shall be目视外观无任何损坏异状No Damageconditioned at ambient room conditions

11、 for 1 to2 hours, after which the specified measurements shall be performed.1 Cycle timea> -2 5± 2°C 30minutesb> 85 ± 2C 30minutes接触阻抗60mQ以下Con tact Resista nee60mQ MAXTPG ELECTRONICS COMPANY LIMITEDTPG PITCH FPC CONNECTOR性能 PERFORMANCE项目ITEM测试条件TEST CONDITION规格PEQUIRMENT盐水喷雾Sal

12、t Spray将样品与适合之FPC连接,使用5± 1%浓度盐水,测 试温度35± 2C ,测试时间48±4小时后于室温下使 用清水冲洗后再干燥Mate applicable FPCand expose to the following salt mist con diti ons. Upon completi on of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specifiedmeas

13、urements shall beperformed.Concen trati on : 5± 1%Spray time :48±4 hoursAmbie nt temperature:35 ± 2C目视外观无任何损 坏异状No Damage接触阻抗60mQ以下Con tact Resista nee60mQ MAX焊锡性Solderability锡温245± 5C ,将导电端子浸入锡炉面至 Housing 距离锡面位置，焊锡时间3土秒.Tip of solder tails and fitting nails into themolte nSolder (held at 245± 5C ) up to 1.0mmfrom the bottom of the hous ing for3± sec on ds.润湿面积75测上,并 不得有漏焊针孔现象.75% of immersed area must show no voids,pi nholes.焊锡耐热性Resista nee toSolderi ng Heat使用红外线回流焊请参考第7点When reflowi ng refer to