VOLVO英文缩写汇总

1、英文缩写:PS (Program start)项目开始PSC (Program strategy con firmation)项目策略确定PTCC (Program Target Compatibility Check point)项目目标分解PTC (Program Target Confirmation)项目目标确定PA (Program Approval)项目批准LR (Launch Readiness)投产准备就绪LS (Launch Sign Off)投产签收J1 (Job1)量产Use for tooling kick off.用于开模Purchasing Related Proc

2、ess/ 采购相尖的流程RFQRequest for quotation which in elude Commercial docume nt and ESOW. Commercial document tells the commercial items and ESOW tells the product information and requirements.询价书包括了商务文件和产品工程规范和要求(ESOW)ESOWESOW1 based on first version drawing for quotationESOW2 based on 2nd version drawing

3、s for nominationESOW3 based on 3rd version drawing for CPAES0W1基于第一版图纸，用于询价ES0W2基于第二版图纸，用于确定供应商ES0W3基于第三版图纸，用于签订CPACPACPA is a commercial contract between Volvo and suppliers for the commodities. It is for the commodities price.CPA是沃尔沃和供应商之间的尖于零件价格的合同。Tooling order / 模具订单Tooling order is an order to

4、 kick off suppliers with commercial tooling and engineering perspectives.模具订单是沃尔沃从工程和商务两 方面来启动供应商的模具工作。PPAP Refer to STA training later 参考后面 ST A 的培训 PurchasingDrawing related Process/ 图纸相尖流程vo1st released version drawing. ESOW1 use it. Design supplier need release VO drawing to Volvo第一版图纸用于ESOW1。设计

5、供应商需要发布V0数据到Volvo系统V12nd released version drawing. ESOW2 use it. Design supplier need release V1 drawing to Volvo第二版图纸用于ESOW2。设计供应商需要发布V0数据到Volvo系统V23rd released version drawing. ESOW3 use it. Can be used for tooling design. Design supplier need release V3 drawing to Volvo第三版图纸用于ESOW3和模具设计。设计供应 商需要发

6、布72数据到Volvo系统FDJLast released version drawing. Used for tooling kick off. Design supplier need releaseFDJ drawing to Volvo最终版图纸用于开模。设计供应商需要发布V0数据到Volvo系统Builds /装车活动:M1 buildM1 build is to verify under body. So under body related parts are affected.M1装车是为了验证下车的设计，所以只有下车体的零件影响到。E3/E4 build / E3/E4 装车

7、E3/E4 build is to verify electrical parts1 function (nodimension requirement). All body electrical parts are affected. Chassis and PT electrical parts are not affected.E3/E4装车是为了验证车身电子零件的性能(对几何尺寸没有要求)，车身电子相尖零件需要支 持该装车。底盘和动力系统的电气相尖的零件不需要支持。EJ E4 Parts E3/ E4<TBattery2Front lampscRoar lamps4Exterio

8、r mirror with auto dim fuclion)外后挪5:vmirror (wit auto dinn fuction)内石初t6Door lock.7f runcklid locks8IP仪农台9Wincjow rAulator10Seatsritoci12sun visorBl13trunk 1 ght若李箱灯1-speaker1!时叭15DHMSL 丫灯16EDSMTO Build (Machi ne Try Out Build)MTO build is to verify BIW (body in white) and body shop process. All sta

9、mp ing parts are affected. No any trim parts are n eeded. Build will only in body shop.Parts must be from job1 tooli ng. This build is before VPMTO是为了验证白车身和焊装工艺的一次装车，只在焊装车间进行，只有冲压件会影响到，总 装零件不需要支持。所有零件必须是量产模具制作的。MTO装车发生在VP装车之前。VP build (Verification Prototype Build)VP build is to verify whole vehicle

10、. All commodities affected. Parts must be from job1 tooling.VP装车验证整车设计，所有零件都需要支持，所有零件必须是量产模具制作的。TT build (Tooli ng Try Build)TT build is first time to verify the job1 in tend process.All parts must be from job1 tooli ng and process. Buildqua ntity is no rmally less tha n 100 carsTT装车是第一次验证量产工艺的装车，所有

11、零件都必需从量产意图工艺制作，一般装车数量少于100辆PP build (Pilot Production Build)PP build is to verify job1 process with more qua ntities vehicle. All commodities affected.Parts must be PSW/SOP level.PP装车是中批量装车验证Job1工艺，所有零件都需要支持，且要达到 PSW/SOPK准。焊装零件：PCF Defi nitio n/PCF 定义PCF: Body Parts Coordi natio nPCF:焊装零件几何尺寸检查PCF M

12、ethods/TPC 方法Use fixtures to simulate sta ndard body the n check the body parts dime nsion.用检具来模拟标准车身，以此来检查焊装零件的几何尺寸。PCF Pla nRefer to VPP参考VPPPCF Related Parts/PCF 相尖零件All body parts所有焊装的零件总装零件：TPC Defini tio n/TPC 定义TPC: Trim Parts Coordi nati onTPC:总装零件几何尺寸检查TPC Methods/TPC 方法Use fixtures to simulate sta ndard body the n check the trim parts dime nsion.用检具来模拟标准车身，以此来检查总装零件的几何尺寸。TPC Pla nRefer to VPP参考VPPTPC affected Parts/TPC 相矢零件1EDS线束2front bumper前保险3Rear bumper后保险杠4Front lamp前心J5Rear lamp后人灯6Radiator grill7Outedoor handl