505编程方式工作卡

1、505 编程方式工作卡应用场合 硝酸汽轮机 (凝汽式调速器组态密码 :1113 日期 2012-10-19一 . Turbine Start (汽轮机启动Manual Start NO Automatic Start YesRate to Min 5.0 RPM/SEC Valve Lmtr Rate 1.0 %/SECUse Idle/Rated YES Idle Setpt ( RPM 1000Rated Setpt ( RPM 9540 Idle/Rtd Rate ( RPM/SEC 15Ext Trips in Trip Relay YES Reset Clears Trip Outp

2、ut YES二、 SPEED CONTROL 转速控制Teeth Seen by MPU 30 Gear Ratio 1 : 1.0Failed Speed Level ( RPM 320 Use Speed Input #2 YESFailed Speed Level ( RPM 320 Off-Line Prop Gain 10Off-Line Int Gain 147 Off-Line Deriv Ratio 0.5On-Line Prop Gain 10 Off-Line Int Gain 0.2Off-Line Deriv Ratio 0.5三、 SPEED SETPOINT VAL

3、UES 转速给定值Overspeed Test Lmt ( RPM 12000 Overspeed Trip ( RPM 10818Max Governor Speed ( RPM 10017 Min Governor Speed ( RPM 8586 Setpt Slow Rate (RPM/SE 5.0 Use Remote Speed Setpt YESRmt Spd Setpt Max Rate 10 Use Critical Speeds YESCritical Speed Rate 50 Critical Speed 1 Max 4300Critical Speed 1 Min 1

4、800 Use Critical Band 2 YESCritical Speed 2 Max 7800 Critical Speed 2 Min 5000四、 OPERATING PARAMETERS 运行参数Generator Application NO Use Local/Remote NO五、 DRIVER CONFIGURATION驱动器的组态Act #1 ( HP is 4 20mA YES Invert Driver Output NOUse Act 1 Flt Shutdown YES Act 1 ( HP Dither 0Use Actuator 2 output? NO

5、Use Act 2 As Readout? NO六、 ANALOG INPUTS 模拟输入Analog Input # 1 Function NOT USED Input 1 4mA Value 0Input 1 20mA Value 100 Analog Input # 2 FunctionInput 2 4mA Value Input 2 20mA ValueAnalog Input # 3 Function Input 3 4mA ValueInput 3 20mA Value Analog Input # 4 FunctionInput 4 4mA Value Input 4 20mA

6、 ValueAnalog Input # 5 Function Input 5 4mA ValueInput 5 20mA Value Analog Input # 6 FunctionInput 6 4mA Value Input 6 20mA Value七、 CONTACT INPUTS 触点输入Contact Input 1 Function Idle/RatedContact Input 2 Function External RunContact Input 3 Function Overspeed TestContact Input 4 Function Contact Input

7、 5 Function Contact Input6 Function Start PermissiveContact Input 7 Function Rmt Spd Setpt EnableContact Input 8 FunctionContact Input 9 Function Contact Input 10 FunctionContact Input 11 Function Contact Input 12 Function八、 FUNCTION KEYS 功能键F3 Key Performs Idle/Rated Blink when not Active NOF4 Key

8、Performs NOT USED Blink when not Active NO九、 READOUTS 读数输出Analog Readout 1 Is NOT USED Readout 1 4mA ValueReadout 1 20mA Value Analog Readout 2 Is Speed SetpointReadout 2 4mA Value 0 Readout 2 20mA Value 12000Analog Readout 3 Is Actuator Demand Readout 3 4mA Value 0Readout 3 20mA Value 100 Analog Re

9、adout 4 IsReadout 4 4mA Value Readout 4 20mA ValueAnalog Readout 5 Is Readout 5 4mA ValueReadout 5 20mA Value Analog Readout 6 Is Actual SpeedReadout 6 4mA Value 0 Readout 6 20mA Value 12000十、 RELAYS 继电器Use Relay # 1 NO Use Relay # 2 NO Use Relay # 3 Yes Relay # 3 is Level SwitchNORelay 3 Energizes On Rmt Spd Setpt EnableUse Relay # 4 NO Use Relay # 5 Yes Relay # 5 is Level Switch NORelay 5 Energizes On Contro