可充电型真空吸尘器充电输入输出测试

1、真空吸尘器充电输入输出测试（可充电型）修订日期修订单号修订内容摘要页次版次修订审核批准2011/03/30/系统文件新制定2A/0/真空吸尘器充电输入输出测试（可充电型）批准：审核：编制：真空吸尘器充电输入输出测试（可充电型）1.0 Purpose /目的To measure the charg ing in put/output of the charger whe n the sample isin recharg ing.評估可充电型樣機的充电器在充电过程中其输入输出是否符合安全 要求.2.0 Defin itio n/概念:2.1Discharge-Operate the sample

2、 no Ion ger to operate with theswitch in the“on”positi on for an additi onal hour.电池完全放电-运行样機直到其完全停止，再保持开关处在开的位 置上多一个小时2.2Recharge-Charge the discharged sample for 16 hours throughthe charger conn ected to supply mains of 120V/60Hz.充滿电-让电池完全放电的样機通过充电器接上120V/60HZ电源充电16小时.3.0 Reference Documents/參考文獻:

3、ULS-01017-DMLW-DataSheet-2001 Form Issued: 1992-07-01 FormRevised: 2006-07-074.0 Equipment/設備:4.1Frequency converter. （變頻电源）4.2Power analyzer（功率分析仪）4.3Datalogger&plug-type module（安捷伦Datalogger和通道插板）4.4J-type thermocouple wire. （J型溫度線）4.5Sicomet99 & Parsec Activator.4.6UL test carpet.（ UL地毯）5.0 Gener

4、al Instructions/說明:5.1Tests may be conducted at any ambient temperature within arange of 10-40C（50-100 F）.測試可在1040C（50100F）之內的環境溫度下進行.5.2Unless otherwise noted, all tests are to be conducted withappliance connected to a 120VAC, 60Hz power source.除非另外讲明,否則所有样機都将连接在120V/60Hz電源下进行測試.5.3All equipment us

5、ed must be calibrated on an annual basis.Calibration stickers with last calibration and calibrationdue date must be affixed to each instrument.使用的所有設備都必須以一年為周期進行調校.載有最後調校日期 和調校周期的調校粘紙必須被粘固在每一個儀表上.5.4For this test, the sample must be operated from chambertemperature.所有测试中样機都从室温状态起动.6.0 Procedure/步驟:6

6、.1Obtain a representative sample of the appliance to be tested.準備一台有代表性的樣機用來測試.6.2Obtain Test Results Form TTR1030 and completely fill in theinformation describing the sample and the equipment used prior torunning the test.用TTR1O30吉果的表格，在測試運作前完整地填入樣機和使用的設 備的情況.6.3Discharge and recharge the sample fo

7、r 16 hours, then discharge it.将样機电池完全放电后,充电16小时再完全放电6.4Connect current channel of module in series into the positivewire of the charger and the voltage channel in parallel connection with thecharger.将充电器正极线从中剪断引两条线接到插板电流通道用来测量充 电器输出电流； 再分不从其正负极线各引一条线到插板电压通道用 来测量充电器输出电压.6.5Connect current channel of

8、module in series into the line conductor of thecord connected to output socket of power analyzer.将功率分析仪的输出插座的火线从中剪断引两条线接到插板电流 通道用来测量充电器输入电流。6.6Plug the module into datalogger and set up relevant configuration.将插板插入安捷伦Datalogger，充电器插入功率分析仪的输出插 座，充电器的输出插入样機的充电孔。6.7Recharge the sample and record corres

9、ponding data in the form describedin Figure 1在电脑中设置好测试参数，开始记录数据后，让样機开始充电，按 图1测试结果表格记下按时刻间隔从零秒开始到充电90分钟时刻 里的输入输出值。7.0 Results/結果:7.1 Use the corresponding Test Results Form TTR1030to report all numericalresults as the information described below.使用TTR1030測試結果的表格,除報告所有數字結果外，還有下列 描述的資料.7.2 Clearly and completely describe all parts that are part ofthis evaluation. Include all model numbers, manufacturing date codes,materials, plastic part revision letters, and modification status.清晰并完整地描述本評估的所有零件,包括所有型號名稱,材料 和塑膠零件改版符號.7.3Clearly and completely describe all special conditions o