盘车电缆装置技术要求

1、盘车电缆装置技术要求一、 型号：CSR-24-CAP（美国）该盘车电缆装置主要用于现场盘装单芯或七芯测井电缆或是当电缆经过一段时间的使用后， 使用该此装置对电缆进行打紧和修整，也可作为简易的倒电缆装置。二、 配置要求三、 主要技术参数：A. POWER UNIT-ECONO DIESEL 动力单元The diesel hydraulic power unit is used to supply hydraulic power to the payoff/take-up normalizer. The power unit consist of a diesel motor which is c

2、oupled to a hydraulic pump. 液压动力单元：用于为给缆/收缆装置提供动力。由一个柴油机与一个液压泵组成。PAYOFF/TAKE-UP NORMALIZER给缆/收缆装置The payoff/take-up and normalizer is capable of holding one reel of cable. It acts as a payoff which allows cable to be spooled off the shipping reel . Because it has the ability to rotate it can be used

3、 to normalize cables, as well as take-up or remove cable from another drum or wireline unit.给缆/收缆装置 给缆就是从运输滚筒缠绕在工作滚筒上。因为这个装置可以把电缆盘装成可以正常使用的电缆，也可以从其他滚筒或电缆装置把电缆盘装好。C. CONTROL PEDESTAL 控制手柄The control pedestal has two Components:控制台有两个组成部分A. Directional control lever:方向控制杆Used to take-up or to layout c

4、able from a reel.用于收缆或将电缆从滚筒上把电缆摊开B. Torque control pressurd valve:扭矩控制阀Regulates the hydraulic pressure necessary to take-up the cable调节收缆时的液压压力控制手柄由两部分组成：A. 方向控制手柄：给缆或收缆;B. 扭矩控制阀：用于保持必要的压力以拉紧电缆。电缆正常化装置的给缆/收缆装置和控制台的配件清单QUANTITY 数量DESCRIPTION 名称和描述114 SHEAVE WHEEL 14英寸滑轮（适用于5.6mm和7.8mm单芯电缆和11.8mm七芯电

5、缆）180PITCH DRIVE SPROCKET 80齿驱动链轮1HYDRAULIC HOSE 15 FEET 液压管线15英尺23/8”HYDRAULIC HOSE 3/8英寸液压管线2BABBIT BEARING 2 15/16” 2-15/16英寸BABBIT轴承1HYDRAULIC GAUGE 0 TO 3000 PSI，0到3000 PSI液压表1HYDRAULIC TORQUE CONTROL VALVE液压扭矩控制阀1DIRECTIONAL CONTROL LEVER方向控制杆180”SHAFT 2 15/16，2-15/16英寸直径80英寸长传动轴1SPROCKET 80 P

6、ITCH 72 TEETH，80齿，72牙链轮2E TYPE BUSHING 2 15/16，2-15/16英寸E 型衬套17 1/2 X 18” O.D BRKING DRUM，7-1/2 X18英寸外径刹车鼓1BRAKE BAND 3/8 PAD，3/8英寸刹车片的刹车带1REEL LOCK 2 15/16，2-15/16英寸缩紧轮2CSR REEL BUSHING 5 1/4” O.D 5-1/4英寸外径CSR 转轴衬套1IDLER SPROCKET 链轮堕轮D. 24” CAPSTAN 24英寸张力轮24”Capstan is used to establish tension dur

7、ing the installation of EM cable. (Rating 3,500 lbs. )24英寸 张力轮用于在安装电缆期间建立高的张力(规定值3500磅）,主要用于盘装直径在5.6mm 和 7.8mm左右的单芯电缆。Weight重量 : 3250 LBS Measurements尺寸: 80” L x 48” W x 43” HPARTS LIST: 24” CAPSTAN 24英寸张力轮配件清单QUANTITY数量 DESCRIPTION描述PART NO部件号.04 BEARING DODGE，DODGE轴承 CSR-0010001 MANUAL HYDRAULIC P

8、UMP 手动液压泵CSR-0030004 TURNBUCKLE 1/2X9” ，松紧螺丝扣CSR-0040002 9” HYDRAULIC CYLINDER液压缸CSR-0050014 9”SPRING 弹簧CSR-0060004 BRAKE BANDS刹车带 CSR-0070002 24” BARRELS 鼓筒CSR-0080001 24” CAPSTAN FRAME张力轮支架CSR-00900E. 36" CAPSTAN 36 英寸张力轮36” Capstan is used to establish high tension during the installation of

9、 EM cable. (Rating 10,000 lbs.)36英寸 张力轮用于在安装电缆期间建立高的张力， (规定值10,000磅), 主要适用于盘装直径在11.8mm左右的七芯电缆。Weight 重量 : 7100 LBS Measurements 尺寸: 122” L x 57” W x 56” HPARTS LIST :配件清单ITEM编号DESCRIPTION描述PART NO.部件号QTY.数量 0112” Brake Spring刹车弹簧 C-36-00108023/8x3/4 Bolt W Nut Lockwasher配有缩紧螺帽的螺栓 C-36-0020803&#

10、189; x 3 ½ Bolt W Nut Lockwasher配有缩紧螺帽的螺栓 C-36-0030404 9” Hydraulic Cylinder液压缸 C-36-00404 05Hydraulic Hose液压管线 C-36-00506¼ Quick Disconnect Hydraulic快速拆卸液压接头 C-36-00601074 7/16 Bearing轴承 C-36-0070408 Bearing Bolts 7/8 x 4 ¾ W Nut and Lockwasher C-36-008 16带螺帽和缩紧片的轴承螺栓09½ Water L

11、ine水管线 C-36-00910½ Water Tee Fitting水管线三通接头 C-36-0100211Swivel Elbows Water 旋转水管拐臂 C-36-0110412½ x ¾ Pin销 C-36-0120413½ x 12 “Turn Buckle松紧螺丝 C-36-0130414Manual Hydraulic Pump手动液压泵 C-36-0140115Brake Pads 刹车片 C-36-0150416 36” Capstan Barrel张力轮鼓筒 C-36-01602A. WEIGHT INDICATOR SYSTE

12、M重量指示系统The weight indicator system is designed to provide a practical method of measuring the tensionon the cable during the installation process.用于显示电缆盘装过程中的张力。B. CABLE BRUSHING SYSTEM电缆刷洗系统Cable Brushing System is used to remove heavy rust and dirt that accumulates on cable. 电缆刷洗系统用于消除在电缆上积累的严重的铁锈

13、和泥（浆）土C. CORE-LUBE CABLE LUBRICATOR缆芯注油润滑装置The Core-Lube Cable Lubricator is used to penetrate, clean and coat cable with lubricates as cable passes through Core-Lube Cable Lubricator. 当电缆穿过缆芯润滑注油装置时，缆芯润滑注油装置可用于电缆缆芯的透入清洗，并且给与电缆涂油润滑。D. POSTFORMER 整形装置The postformer is used in the operation of normalizing a cable. Also it can be used for removing kinks in a cable. 再成形装置用于正常化电缆绳的操作，并且它可以为去除