浅论如何正确使用涡轮增压器中英文对照

1、浅论如何正确使用涡轮增压器中英文对照Discussion on how to correctly use the turbocharger in Chinese and English. 随着汽车工业地飞速开展,汽车已逐渐走进到千家万户,在满足乘坐地舒适性、使用地经济性要求后,人们对于汽车地动力性地要求也逐步提高,在现有地技术条件下,给发动机加装涡轮增压器是最好地解决方法.一般情况下,加装增压器后,发动机地功率及扭矩要比加装前增大2030.小排量,大功率,代表着当前发动机技术地最高水平.比普通发动机拥有更好地动力,也有更好地燃油经济性.b5E2RGbCAPWith the rapid deve

2、lopment of automobile industry, the automobile has gradually entered into thousands of households, the ride comfort, economy of use requirements, people also gradually improved the cars request, under the conditions of the existing technology, to the engine with turbocharger is the best solution. Un

3、der normal circumstances, install the supercharger, engine power and torque than with increased 20%30%. Small volume, high power, and represents the highest level of current engine technology. To have better power than the ordinary engine, also have better fuel economy.p1EanqFDPw文档来自于网络搜索 什么是涡轮增压器？它

4、是安装在发动机排气管道上地一台精致地空气压缩机,利用发动机排出地废气推动涡轮室内地涡轮旋转,涡轮又带动同轴地叶轮旋转,这样,叶轮就把从空气滤清器进来地空气进行压缩,使之增压进入汽缸.由于进入气缸地空气密度增大,可使更多地燃油充分燃烧,因而大大提高了发动机地功率,降低了燃油消耗. 由于该系统是利用发动机排出地废气驱动涡轮,所以涡轮增压器经常在高速、高温下工作,涡轮端地温度在600度以上,增压器也以每分钟8万-10万转地速度高速旋转.所以为了保证增压器地正常工作,就要正确使用和维护保养涡轮增压器.在使用地过程中应注意以下事项.DXDiTa9E3dWhat is the turbocharger?

5、It is installed in the engine exhaust pipe of a sophisticated air compressor, drive a turbine room of the turbine rotation by waste gas discharged by the engine, turbine driven by another coaxial impeller rotation, so, the impeller to compress the air cleaner air, so that pressurized into the cylind

6、er. As the density of air into the cylinder increases, can fully burn more fuel, thus greatly increasing the power of the engine, reducing fuel consumption. Because the system is to use the engine emissions drive turbine turbocharger, so often in high speed, working under high temperature, turbine e

7、nd temperature is above 600 degrees, superchargers also per minute to 80000 -10 000 rpm speed of high-speed rotation. So in order to ensure the normal work of the supercharger, it is necessary to correctly use and maintenance of turbocharger. In the use of the process should pay attention to the fol

8、lowing matters.RTCrpUDGiT个人收集整理 勿做商业用途 1 涡轮增压发动机冷启动考前须知1 turbocharged diesel engine cold starting points for attention5PCzVD7HxA 汽车发动机冷启动后,不能急加油,应先怠速运转三到五分钟,这是为了使机油温度升高,流动性能改善,从而使涡轮增压器轴承得到充分润滑,这一点在冬季尤为重要.否那么易使增压器转子轴、轴承、密封环等部件因缺油而早期磨损.jLBHrnAILgAutomobile engine cold start, not rush to refuel, should

9、 first idling for three to five minutes, this is to make the oil temperature, flow performance is improved, so that the turbocharger bearing lubricated sufficiently, this is particularly important in the winter. Otherwise it is easy to make the supercharger rotor shaft, bearing, seal ring and other

10、parts of early wear due to lack of oil and.xHAQX74J0X文档收集自网络，仅用于个人学习 对于停车时间较长(一周以上地车辆,在发动机重新启动前,一定要先将增压器予以润滑.方法是松开增压器进油管接头,向进油口倒入干净地与油底壳同牌号地机油.另外,在更换润滑油、清洗或更换机油滤清器时,都应按上述方法向涡轮增压器加注润滑油,然后再启动车辆.LDAYtRyKfEFor the parking time is longer (more than one week of the vehicle, the engine before restarting, m

11、ust first be lubrication of turbocharger. Method is to loosen the turbocharger inlet pipe joint, to the oil inlet into the clean and the oil pan with the grade of oil. In addition, the replacement of lubricants, cleaning or replacement of oil filter, should according to the above method to the turbo

12、charger lubricating oil, and then start the vehicle.Zzz6ZB2Ltk个人收集整理 勿做商业用途 2 涡轮增压发动机熄火考前须知2 turbocharged engine flameout note 发动机在带有负荷或长时间高速运转后,不能马上熄火.因为发动机正常工作时,机油泵会向涡轮增压器输送机油,用于转子轴承地润滑和冷却,发动机突然熄火后,油泵停止工作,机油压力迅速降为零,机油润滑中断,涡轮增压器运转产生地热量就无法被机油带走,这时增压器涡轮局部地高温会传到中间地轴承支撑壳上,轴承支承壳内地热量不能迅速被带走散失掉,而增压器地转子仍在惯

13、性作用下做着高速旋转.这样就可能造成涡轮增压器转轴与轴套之间“烧死而损坏轴承和转轴.另外,发动机突然熄火后,排气歧管地高温会很快传递到涡轮增压器壳体上,增压器内部地机油也会因为过热而变质,甚至生成积碳.积炭积累过多就会阻塞进油口,加速涡轮转轴与轴套之间地磨损.正确地熄火方法是：发动机熄火前应怠速运转三到五分钟,待增压器转子转速降低和机油温度有所下降后,再熄火停车.在行使过程中,严禁采用“加速-熄火-空档滑行地操作方法,这样也会因为机油泵停止供油而损坏涡轮增压器. 此外,要防止发动机长时间地怠速运转,否那么也会因怠速时机油压力偏低,增压器转子轴浮起受影响,而导致转子轴、轴承和密封环等部件地早期磨

14、损.dvzfvkwMI1文档收集自网络，仅用于个人学习Engine with load or long time high-speed operation, not immediately. Because the normal work of the engine, engine oil pump can transport oil to the turbocharger, for rotor bearing lubrication and cooling, after the engine stops suddenly, the oil pump stops working, the oi

15、l pressure decrease rapidly to zero, lubrication oil interruption, turbocharger operating heat generation cannot be oil away, bearing shell when the turbocharger part of the high temperature to the middle of the upper bearing shell, heat can not be quickly dissipated away, while the rotor turbocharg

16、er is still under the inertia effect do high-speed rotation. This may result in between the turbocharger shaft and the shaft sleeve and the shaft bearing damage. In addition, after the engine stops suddenly, the exhaust manifold temperature will quickly transfer to the turbocharger shell, oil the tu

17、rbocharger internal will also because of overheating and metamorphism, and even generate carbon. Coke will be the accumulation of excessive blocking oil inlet, accelerated wear between the turbine shaft and sleeve. Flameout is right: the engine flameout ago should be idle for three to five minutes,

18、reduce the turbocharger rotor speed and oil temperature decreases, then shut down. In the process of the exercise, operation is strictly prohibited methods accelerated - off - neutral glide, it will also because oil pump stop feeding and damaged turbocharger. In addition, long time to avoid the engi

19、ne idling, otherwise will idle oil pressure is low, the supercharger rotor shaft floating affected, resulting in early wear of the rotor shaft, bearing and seal components.rqyn14ZNXI文档收集自网络，仅用于个人学习 3 选择质量好地机油 3 choose good quality oil 在涡轮增压器地作用下,进入燃烧室地空气量大幅度地提高,在发动机燃烧室容积不变地情况下,相当于提高了压缩比,使发动机地工作强度大大高

20、.涡轮增压发动机地高机械加工精度,严格地装配技术.这些都决定了涡轮增压发动机处于高温、高转速、大功率、大扭矩、低排放地工况下.所以在选用涡轮增压发动机使用地机油时,要求所用地机油必须具有良好地抗磨、耐高温性,容易建立高强度油膜.目前地合成机油或半合成机油都可以满足这一要求,所以除了使用原厂规定机油外还可以选用合成机油、半合成机油等高品质润滑油.EmxvxOtOcoOn the turbocharger under the action of air into the combustion chamber, greatly increase the amount, in the engine c

21、ombustion chamber volume under the condition of invariable, equivalent to improve the compression ratio of the engine, the working strength is high. High machining precision of the turbocharged engine assembly technique, strict. These are decided by the turbo engine in high temperature, high speed,

22、large power, large torque, low emission conditions. So in the selection of the turbocharged engine used for oil, the oil must have good wear resistance, high temperature resistant, easy to build high strength oil film. Synthetic oil at present or semi synthetic oil can satisfy this requirement, so i

23、n addition to the provisions of the use of original oil also can use synthetic oil, synthetic oil of high quality lube oil.SixE2yXPq5个人收集整理 勿做商业用途 4 经常检查涡轮增压器地密封环是否失效4 regularly check the sealing ring of turbocharger failure6ewMyirQFL 如果涡轮端油封失效,废气会通过密封环进入发动机润滑系统,时间久了就会使机油过早失效,此外,在发动机低速运转时机油也会通过密封环进入

24、排气管,从排气管排出排出,造成排气管冒烟现象；如果压气机端油封失效,增压器内地机油便会窜入压气机壳,随着进气一起被吸入气缸内燃烧,造成 机油过度消耗,产生“烧机油地现象,严重时还会造成气缸内积炭增多.kavU42VRUsIf the failure of turbine end oil seal, the exhaust gas through the sealing ring into the engine lubrication system, time will make the oil premature failure, in addition, the engine running

25、 at a low speed, the oil will through the sealing ring into the exhaust pipe, exhaust emissions from the exhaust pipe, exhaust pipe smoking phenomenon caused by。 if the failure of compressor end seal, inside the intensifier the oil will enter the compressor casing, with intake are sucked into the cy

26、linder combustion, resulting in excessive consumption of oil, burn oil phenomenon, serious when can cause the carbon deposit increase.y6v3ALoS89资料个人收集整理，勿做商业用途 5 定期更换机油5 the regular replacement of oil 涡轮增压器地转子轴与其轴承地配合非常精密,如果机油过脏或变质,会将杂质或磨粒等带入增压器内,轻那么加速轴承磨损,重那么使转子轴与轴承咬死.因此,一定要定期更换机油,在每次换机油时,最好将机油滤清器一并更换.M2ub6vSTnPThe matching of turbocharger rotor shaft and bearing very precise, if the oil too dirty or deterioration, will bring the impurities or abrasive, turbocharger, light accelerated bearing wear, while in the rotor shaft and bearing seizure. Th