扶梯工地安装指导

1、会计学1扶梯工地安装指导扶梯工地安装指导2桁架拼接3桁架4桁架拼接56F8NEXXXXX: 合同号数字: 接头板的编号（如1表示编号为1的接头）划线: 连接好之后位置标记UP上(DOWN下): 接头板的上下位置标记桁架拼接7桁架拼接注意: 所有连接完成之后应检查底板连接处是否 会漏油.8梯路拼接9梯级链条拼接10张紧架调整12131415161718调整垫片土建垫板土建支撑支撑板高度调节螺栓1920 扶梯起吊之前将中间支撑固定在桁架上，并在土建支撑上放置垫板。21q注意: 线的两端必须位于倾斜段22232426注意：玻璃夹紧件底部必须和支架螺栓接触。27-玻璃栏板的安装顺序为从两头往中间安装；

2、-非标段玻璃位于倾斜段上头部；-对齐上下平层玻璃栏板，通过和工厂做好的标记对齐玻璃位置，然后定位其他玻璃的位置并在玻璃夹紧件上做好标记；-玻璃之间的缝隙保留 12 mm.28- 采用水平仪检查玻璃栏板的垂直性；- 如果垂直度需要调整，请先松开玻璃夹紧固定支架；293031- 连续铺设橡胶垫 下头部倾斜段上头部32- 上下R段弹簧卡子之间的间距大致在250mm左右，直线段弹簧卡子之间的间距大致在300mm 左右；- 在导轨接头部位距离端部20mm加装弹簧卡子。上R段下R段端部直线段3334q 导轨接头3536乘客分支安装工具返回分支安装工具q 返回分支37 松掉T型螺母，通过螺杆调节扶手带张紧程

3、度。螺杆滚轮群T型螺母38提升高度提升高度 H弹簧长度弹簧长度 L7000H80001026000H70001055000H60001074000H5000109.53000H40001122000H3000115H2000117（mm）扶手压紧链39上部滚轮群4041- 确保入口外壳和外盖板平整光滑过渡，可以通过调节螺栓实现。q 安装外壳42- 调整扶手带和入口橡胶头的间隙至0.5 3 mm。43- 注意使用连接板，将内壳和内盖板连接平滑。.44封板安装必须小心仔细。45横梁和直梁已经在新的结构中被取消。46 所以，只需调整前沿板边框螺栓的高度和装饰地面的高度平齐即可。48 Visually

4、 inspect that the groves in the steps are centered in the comb teeth.49 The clearance shall not exceed 4 mm at each side, and 7 mm for the sum of clearance measured at both sides.50 Visually inspect the skirt panels and deckings for unsafe or damaged condition.51 The gap between each glass panel sho

5、uld be 2 mm.52 Visually inspection for any damaged steps.53 Test handrail play in the roller newel bow. Should not move more than 5 mm in either direction.54 Let the step band rotate 1.5 times around the track, pay attention of any unusual noise or vibration in the handrail system and track system.5

6、5 Reverse direction and repeat test.56 While the escalator is running, ride the escalator and pay attention to any noise and vibration.57 Mark a line with chalk on the skirt panel that located on upper landing, and make a marker on a step, start the escalator, push the emergency stop button while th

7、e step pass the line, then measure the distance. The stopping distance should be a little more than 200 mm.58Press the cover of the Handrail Entry Safety device so that the safety switch inside the Handrail entry box is activated, and the corresponding symbol should be displayed on the operation pan

8、el that located on upper landing.59Remove the fastening screws holding the comb fastened.60Pull up the comb plate as shown, so that the safety switch is activated and the corresponding symbol should be displayed on the operation panel. Then re-install original fastening screws back into comb.61Get t

9、he comb plate away as shown, so that the safety switch is activated and the corresponding symbol should be displayed on the operation panel. 62Handrail Entry Safety Device ULEmergency Stop Button ULComb Plate Safety DeviceSkirt Panel Safety DeviceSkirt Panel Safety DeviceBroken Step and Chain Wheel

10、Safety DeviceMain Drive Chain Safety DeviceFloor Plate ContactSkirt Panel Safety DeviceSkirt Panel Safety DeviceEmergency Stop Button LLBroken Step and Chain Wheel Safety DeviceHandrail Entry Safety Device LLBroken Step Chain Safety DeviceFloor Plate Contact6466-If the electrical work is done on the

11、 unit and the power is available, run the unit with the inspection box upwards and using a brush to oil the step chain piece by piece.-If there is not yet power on the jobsite available, or the electrical part of the unit is not finished, you must move the unit by hand using the handwheel every time

12、 50 mm to avoid that the step chain wheels and step wheels get flat spots. In this case, the tension carriage springs should be released until the springs are completely slack and you should keep it this way until you start running the unit with power.67-Remember that on glass balustrade-units the p

13、ressure rollers of the friction wheel drive system are after the test run in the factory released and should remain this way until the unit is prepared for handover, thus avoiding the rollermarks on the handrails.-On units directly exposed to the weather you should be even more carefully, they require more frequent oiling due to the frequent rain. In wintertime with temperatures below 0 Celsius you must start the heating at least one hour before you begin with the maintenance to