某科技有限公司产品说明书

1、深圳市慧拓鑫科技有限公司Shenzhen Hui Tuo Xin Technology Co., Ltd.产品资料Product information1 TOP 电源防雷箱系列(TOP Power lightning protection box series )22 TP 限压型电源防雷模块系列(TP Voltage limiting type power supply lightning protection module series ). 53 TP 直流电源防雷模块系列(TP DC power supply lightning protection module series )8

2、4 TCP 电源未端精细防护防雷器系列(TCP Power supply terminal fine protective lightning arrester series ) .115 TDC 电源插座(TDC Power supply lightning protection socket series)146 TV 视频防雷器系列(TV Video arrester series) 177 T 视频/射频防雷器系列(T Video / RF lightning arrester series) 208 TC 控制线路防雷器系列( TC Control circuit lightning

3、 arrester series) 239 10/100M 网络线路防雷器(10/100M Network circuit lightning arrester) 2510通讯专线防雷器(Communication line lightning arrester) 2811 TT 天馈线路防雷器系列(TT Antenna line arrester series) 301、TOP 电源防雷箱系列(TOP Power lightning protection box serie§产品介绍 Product introductionTOP电源防雷箱系列依据IEC标准设计，8/20波形最大通

4、流容量20KA-100KA，能对电源系统的浪涌电压进行有效的钳制， 电源B、C、D级产品均具备。TOP Power lightning protection box series is designed according to IEC standard, 8/20 wave maximum flow capacity of 20KA-100KA, to power system voltage surge effectively clamped, power supply B, C, D products have.TOP电源防雷箱配系列具备测试指示灯功能，能有效的指示防雷箱工作电源、浪涌防

5、护状态，并可选备雷击计数、远程遥 信监测功能。TOP Power lightning protection box series Have a test indicator function , Can effectively indicate the lightning protection box power supply、Surge protection status And optional lightning counting 、Remote remote monitoring function 电涌保护器失效报警功能/相零反接及接地不良报警 (Surge protection de

6、vice failure alarm function / Phase zero reverse connection and grounding alarm ) 雷击计数显示、电源指示功能(可选) Lightning counting display , Power indicator function (Optional) 电浪保护器远程监测功能(失效) Remote monitoring function ( Failure) 残压低、响应时间快 Residual depression and Fast response time 安装设计人性化、结构严谨 Installation de

7、sign of humanity and Strict structure 工作环境温度适应性强 Working environment temperature adaptability 外壳保护等级高 Shell protection grade产品性能参数(共性)Product performance parameters (Common )SPD 端口SPD Port一端口One portSPD类另ijSPD Category限压型Voltage limiting type保护模式Protected modeL-PE/N-PEL-PE/N-PE最大持续运行电压UcMax. continu

8、ous operating a.c. voltage Uc320/385V320/385V失效指示Failure indication亮为正常工作、灭为故障指示Light for the normal work 、 Off for fault indication工作环境温度Operating temperature range parallel/series-40/85 C-40/85 C外壳保护等级Degree of protectionIP50IP50响应时间Response time< 251s& 251s产品性能参数(个性) Product performance pa

9、rameters ( Personality)型号(Model)工作电压Nominal a.c. voltage标称放电电流In (8/20 g S Nominal discharge current In (8/20 s)最大放电电流Imax (8/20 g S Max.discharge currentImax(8/20s)保护水平)UpVoltage protection level up连接线 最小安装导体 截面 Cross-sectiona l area (min.)接地线 最小安装导体截面Cross-sectional area (min.)TOP-100A-3380V60KA10

10、0KA2500V-225 mm-235 mmTOP-60A-3380V30KA60KA2500V,-216 mm一225 mmTOP -40-3380V20KA40KA1800V10 mm216mm2TOP -40-1220V20KA40KA1800V210 mm,- 216mmTOP -20-3380V10KA20KA1500V210 mm,- 216mmTOP -20-1220V10KA20KA1500V210 mm,- 216mm产品适用范围：The scope of products : 通信、电力、金融、民航、铁路等电源系统的保护 Communications, electricit

11、y, finance, civil aviation, railways and other power system protection 建筑物总配箱、室外配电箱、楼层分配箱 Buildings with a total box, outdoor distribution box, floor distribution box 配电柜电箱无安装位置但须安装第一级防雷设施的环境 Power distribution cabinet electric box without installation position but must be installed first stage ligh

12、tning protection facility environment 无人值守但须安装第一级带遥信指示的防雷设备的环境 Unmanned but to be fitted with remote signal indicative of the first level of mine equipment environment需要有第一级电涌保护失效指示及报警指示及雷电泄放记录的环境 Need to have the first surge protection failure indication and alarm indication and lightning discharge

13、 recording environment产品图:Product picture:产品尺寸:Prodct size chart:120 ma I ,：52 mm安装说明：Installation instructions :1、取出箱子钥匙，插进锁孔打开防雷箱面板1、Remove the box keys, Inserted into the keyhole to open the thunder box panel2、防雷箱体固定在墙面上。2、Lightning protection box fixed on the wall3、用电缆剪线钳裁剪相应长度的黄、绿、红、蓝色四种电源线及黄绿双

14、色地线。3、 Cutting the appropriate length of cable wire cutters, yellow, green, red, blue four power cord and the yellow-green ground4、根据现场的接线方式对每条线末端做铜鼻子；选用 )150A开口线鼻子或者与线径相应的国标圆口线鼻子，开口线鼻子用电烙 铁搪锡；圆口线鼻子用液压钳压接并搪锡。4、According to the connection on each end of the line do copper nose ； Selection of > 150

15、A opening line of the nose or with a diameter corresponding to GB Round the mouth line nose Opening line of the nose with electric iron Boring tin； Roundmouth lines the nose with the hydraulic crimping and boring tin5、将防雷箱连接好。5、Lightning box connected6、把五条连接导线穿管固定；管可选用PVC管槽、镀锌铁管槽、黄腊管、波纹管、蛇皮管等。6、The

16、five connecting conductor pipe is fixed : Tube can be used PVC pipe trough, galvanized iron pipes slot, yellow wax tubes, bellows, snakeskin tube。7、停电接线，把黄、绿、红、蓝、黄绿五种线分别与电源配电柜内L1、L2、L3、N、PE相并联连接，并联安装于电源系统的空气开关进线端，并确保连接可靠。7、Blackout wiring , The yellow, green, red, blue, yellow and green five line is

17、 respectively connected with the power distribution cabinet L1, L2, L3, N, PE phase parallel connection , nstalled in parallel in the power system into the air switch line side And ensure a reliable connection8、固定配电箱内的连接导线，恢复供电。8、 Fixed power distribution box connecting wire, Restoration of electric

18、ity9、锁好防雷箱，按下测试按钮指示灯亮，安装完毕。9、 Lock the lightning protection box ， Press the test button indicator light ， and Installed* 安装注意事项*Installation Notes1 、必须由专业持证电工进行安装。1 、 Must be professional certified electrician to install2、接地电阻04Q2、Grounding resistance <4 0,2 、 TP 限压型电源防雷模块系列( TP Voltage limiting

19、type power supply lightning protection moduleseries)产品介绍 Product introductionTP 系列电源防雷模块依据IEC 标准设计，8/20 波形最大通流容量20KA-80KA ，能对电源系统的浪涌电压进行有效的钳制，能对电源系统的浪涌电压进行有效的钳制，电源B、 C、 D 级产品均具备，依据不同的配电系统(TT/TN/IT )可选择多种组合方式。TP series SPD according to IEC standard design, 8/20 wave maximum flow capacity of20KA-80KA,

20、 to power system voltage surge effectively clamped, power supply B, C, D products have， According to different distribution system( TT/TN/IT ) can choose a variety of combinations. 模块设计、安装方便 Modular design 、 Easy to install 模块为标准35mm 导轨式安装 Module for the standard 35mm DIN rail installation 内置过流过热、温控

21、断路技术 The built-in overcurrent overheat, temperature control circuit technology 单模块最大放电电流：20-80kA (8/20 ii)s Single module of the maximum discharge current of 20-80kA (8/20 科 s) 漏电流小、残压低 Low leakage current, low residual voltage 反应速度：10-9 秒级 Speed of response： < 1ns 高能电涌保护 High-energy surge protec

22、tion 失效指示 become invalid indication 遥控报警信号常开/常闭触点端子(可选) Remote alarm signal Normally open / normally closed contact terminal( Optional )产品性能参数(共性)Product performance parameters (Common )SPD 端口SPD Port一端口One portSPD类另1JSPD Category限压邪Voltage limiting type电源系统TT-TN-ITPower systemTT-TN-IT失效指示Failure in

23、dication窗口跳红The window to jump the red工作环境温度Operating temperature range parallel/series-40/85 C-40/85 C外壳保护等级Degree of protectionIP20IP20响应时间Response time< 251s< 25ns型号（Model）TP80TP40TP20TP-N额定电压UnNominal a.c. voltage Un220V220V220V220V最大持续运行电压UcMax. continuous operating a.c. voltage Uc385V385

24、V355V275V标称放电电流 In (8/20 v)Nominal discharge current In(8/20 s)心40KA20KA10KA80KA最大放电电流 lmax (8/20Max. discharge current Imax(8/20 s)心80KA40KA20KA-限制电压UpVoltage protection level Up<2300V<1800V<1500V<1200V前置过流保护Prepositive overflowing protection63A/35KA32A/10KA16A/6KA-产品性能参数(个性) Product pe

25、rformance parameters ( Personality)产品图片：Product picture:产品适用范围：The scope of products :通信、电力、金融、民航、铁路等电源系统的保护 Communications, electricity, finance, civil aviation, railways and other power system protection建筑物总配箱、室外配电箱、楼层分配箱 Buildings with a total box, outdoor distribution box, floor distribution box

26、产品尺寸图：Prodct size chart:安装说明：Installation instructions :1、防雷模块前串联过流保护装置1、Lightning protection module series overcurrent protection devices2、防雷模块固定在35mm导轨上。2、Lightning protection module is fixed at 35mm rail3、用电缆剪线钳裁剪相应长度的黄、绿、红、蓝色四种电源线及黄绿双色地线。3、 Cutting the appropriate length of cable wire cutters, y

27、ellow, green, red, blue four power cord and the yellow-green ground4、根据现场的接线方式对每条线末端做铜鼻子；选用 )150A开口线鼻子或者与线径相应的国标圆口线鼻子，开口线鼻子用电烙 铁搪锡；圆口线鼻子用液压钳压接并搪锡。4、According to the connection on each end of the line do copper nose ； Selection of > 150A opening line of the nose or with a diameter corresponding to

28、 GB Round the mouth line nose Opening line of the nose with electric iron Boring tin ； Round mouth lines the nose with the hydraulic crimping and boring tin5、将防雷模块连接好。5、Lightning protection module connected6、把五条连接导线穿管固定；管可选用PVC管槽、镀锌铁管槽、黄腊管、波纹管、蛇皮管等。6、The five connecting conductor pipe is fixed : Tub

29、e can be used PVC pipe trough, galvanized iron pipes slot, yellow wax tubes, bellows, snakeskin tube。7、停电接线，把黄、绿、红、蓝、黄绿五种线分别与电源配电柜内L1、L2、L3、N、PE相并联连接，并联安装于电源系统的空 气开关进线端，并确保连接可靠。7、Blackout wiring , The yellow, green, red, blue, yellow and green five line is respectively connected with the power distr

30、ibution cabinet L1, L2, L3, N, PE phase parallel connection , nstalled in parallel in the power system into the air switch line side And ensure a reliable connection8、固定配电箱内的连接导线，恢复供电。8、 Fixed power distribution box connecting wire, Restoration of electricity9、安装完毕。9、Installed*安装注意事项*Installation No

31、tes1、必须由专业持证电工进行安装。1、 Must be professional certified electrician to install2、接地电阻04Q2、Grounding resistance < 4 Q3、TP 直流电源防雷模块系列(TP DC power supply lightning protection module series)产品介绍 Product introductionTP系列直流电源电涌保护器依据IEC标准设计,TP系列直流电涌保护器具备大的雷电流泄放能力，每位的最大放电电流20kA ,适用于直流供电系统的末级保护，依据不同的直流电源电压可选择

32、各种相应的规格。TP series DC power SPD according to IEC standard design, TP series DC surge protector with a large lightning current discharge capacity of, Each of the maximum discharge current of 20kA, Suitable for DC power supply system of the final protection, On the basis of different DC power supply vo

33、ltage can be selected by the corresponding specifications模块设计、安装方便 Modular design > Easy to install 模块为标准35mm导轨式安装 Module for the standard 35mm DIN rail installation 内置过流过热、温控断路技术 The built-in overcurrent overheat, temperature control circuit technology 单模块最大放电电流：20-80kA (8/20 g)s Single module o

34、f the maximum discharge current of 20- 80kA (8/20 心 s)漏电流小、残压低 Low leakage current, low residual voltage 反应速度：10-9秒级 Speed of response: < 1ns高能电涌保护 High-energy surge protection 失效指示 become invalid indication遥控报警信号常开/常闭触点端子(可选) Remote alarm signal Normally open / normally closed contact terminal(

35、Optional)产品性能参数(共性)Product performance parameters (Common )SPD 端口SPD Port一端口One portSPD类另1JSPD Category限压型Voltage limiting type电源系统Power system直流电源DC power supply失效指示Failure indication窗口跳红The window to jump the red工作环境温度Operating temperature range parallel/series-40/85 C-40/85 C外壳保护等级Degree of prote

36、ctionIP20IP20响应时间Response time< 251s& 25ns型号（Model）TP24DCTP48DCTP75DCTP110DCTP380DC额定电压UnNominal a.c. voltage Un24DC48DC75DC110DC380DC最大持续电压UcMax. continuous operating a.c. voltage Uc30DC85DC85DC120DC385DC标称放电电流 In (8/20 v)Nominal discharge current In (8/20 s)10KA科10KA10KA10KA20KA最大放电电流 lmax

37、(8/20Max. discharge current Imax(8/20 s)p20KA20KA20KA10KA40KA限制电压UpVoltage protection level Up<450V<450V<450V<1200V<1200V前置过流保护Prepositive overflowing protection16A/6KA16A/6KA16A/6KA32A/6KA32A/6KA产品性能参数(个性) Product performance parameters ( Personality)产品图片：Product picture:产品适用范围:The s

38、cope of products :直流配电屏 DC distribution screen直流供电设备 DC-powered equipment直流配电箱 DC distribution box电子信息系统（如消防机房直流线路） Electronic information system。产品尺寸图：Prodct size chart:1 8mm+）'：+>口制TiPliDCVtt&ori 1FKDC安装说明：Installation instructions :1、防雷模块前串联过流保护装置1、Lightning protection module series ov

39、ercurrent protection devices2、防雷模块固定在35mm导轨上。2、Lightning protection module is fixed at 35mm rail3、连接线线径要求：TP24DC、TP48DC、TP75DC、TP110DC、TP380DC ,连接线 漪 mm2,接地线 高0 mm2。3、Cable diameter requirements : TP24DC、TP48DC、TP75DC、TP110DC、TP380DC, Connecting wire >6 mm2,2Ground wire > 1 mm4、连接导线长度要求：电涌保护器两

40、端的连接导线长度R.5米。4、Connecting wire length requirements : Surge protection devices at both ends of connecting wire length < 0.5m5、TP电涌保护器应安装在直流供电设备的负荷侧。5、TP Surge protective device should be installed in DC power supply equipment of the load side6、TP电涌保护器前端必须串联过流保护装置，过流保护装置参数的选择：TP380DC,额定电流 32A,分断电流

41、10KA ; TP24DC、TP48DC、TP75DC、TP110DC,额定电流 16A,分断电流 6KA。6、TP Surge protective device, front-end must be connected in series overcurrent protective device , rameter selection of overcurrent protective devices: TP380DC,Rated current 32A , Breaking current 10KA ; TP24DC、TP48DC、TP75DC、 TP110DC, Rated curr

42、ent 16A , Breaking current 6KA7、安装距离：与电压开关型电涌保护器距离石米。7、Installation distance : Voltage switch type surge protector distance > 5m8、安装完毕。8、Installed4、TCP 电源未端精细防护防雷器系列(TCP Power supply terminal fine protective lightning arresterseries)产品介绍 Product introductionTCP系列模块化电源防雷器依据 IEC标准设计，TCP系列电源防雷器每位具备

43、2路电涌保护功能，每位的最大放电电流10KA (8/20 适用于供电系统的末级保护，依据不同的电源电压选择各种相应规格。TCP Series modular power supply SPD according to IEC design,TCP Series SPD each with 2-way surge protector, Each the maximum discharge current of 10KA (8/20 科,s)Apply to the supply system of The last level protection失效检测指示 become invalid in

44、dication 单模块最大放电电流：10kA (8/20 g)s Single module of the maximum discharge current of 10kA (8/20 科 s) 模块为标准35mm导轨式安装 Module for the standard 35mm DIN rail installation 内置过流过热、温控断路技术 The built-in overcurrent overheat, temperature control circuit technology产品性能参数：Product performance parameters型号（Model）T

45、CP012TCP024TCP024ACTCP220SPD 端口一端口一端口一端口一端口SPD Port1 Port1 Port1 Port1 PortSPD类型组合型组合型组合型组合型SPD TypeCompoundCompoundCompoundCompound电源系统12V直流单相24V直流单相24V交流单相220V交流单相Power system12V DC24V AC24V DC220V ACsingle-phasesingle-phasesingle-phasesingle-phase额定电压Un12V24V24V220VNominal a.c. voltage Un最大持续电压Uc

46、Max. continuous operating a.c. voltage Uc15V30V30V320V标称放电电流 In (8/20 v)sNominal discharge current In (8/20 s)5 kAi5 kA5 kA5 kA最大放电电流 lmax (8/20 v)Max. discharge current Imax(8/20 s)；10 kAL10 kA10 kA10 kA限制电压UpVoltage protection level Up30V42V42V700V失效指示Failure indicationNONONOGREEN: OKRED: Fail断路装置

47、Breaking arrangement保险丝(温度)Fuse(Temperature)内置Internal机械性能Mechanical properties连接导线Connecting wire1.5-2.5mm21.5-2.5mm2安装Installation35mm 标准导轨(EN50022/DIN46277-3 )35mm standard rail (EN50022/DIN46277-3 )工作环境温度Operating temperature range parallel/series-40/85 C外壳材料Case Material符合 UL94V-0Conform UL94V-

48、0外壳保护等级Degree of protectionIP30产品图片：Product picture:产品适用范围:The scope of products : 未级保护 The latter level protection对安装空间要求较小的设备保护 Installation space requirements of smaller equipment protection产品尺寸图：I s - IlVrtson V iON>t TCP012IN> 1 PE 2Prodct size chart: 1 M ?聃I IWA*: IOKA Un 12Y Uc dSv Up产品

49、安装说明：Installation instructions :产品安装时，首先须将产品连接至可靠地线。Product installation, the product must be connected to a reliable ground.1、将TCP系列浪涌保护器固定到 35mm标准导轨上。1、TCP series SPD is fixed to the 35mm standard rail2、TCP电涌保护器与被保护设备安装距离4米。2、TCP SPD and the protected equipment installation distance < 1m.3、将被保护

50、设备原输入线路插入TCP电涌保护器标有(IN )端口螺柱卡接孔内，标有(OUT)端与设备连接，锁紧螺丝。3、 Protective equipment of the original input line will be inserted TCP surge protection device marked with (IN) port stud card accesshole (OUT) end device is connected, tighten the screws.4、接地要求：4、Grounding requirements :4.1、 TCP系列电涌保护器的地线须接在标有In端

51、的接地螺丝上，接地线22.5 mm2。24.1 TCP series surge protector ground shall be connected to the grounding screw on the In side, The ground wire > 2.5mm4.2、 接地电阻04Q4.2、 Grounding resistance .<40,5、异常状况5、Abnormal conditions5.1、当线路中信号电平超过选用的TCP电涌保护器的Uc值时，TCP电涌保护器会损坏，同时出现信号中断。5.1、 When the line signal level o

52、ver the selection of TCP surge protector Uc value, TCP surge protection device will be damaged, while the interrupt signal.5.2、 当信号(或交流、直流电路)电流超过TCP电涌保护器的负载电流时，电涌保护器会发热损坏。5.2、When the signal (or AC and DC circuit) current exceeds the load current of the TCP surge protector, surge protector, heat dam

53、age. 出现上述两种情况时，请迅速取下TCP电涌保护器，重新选择与线路信号特性相匹配的TCP电涌保护器。The above two cases, quickly remove the TCP surge protector, re-select line signal characteristic that matches the TCP surge protector.5、TDC 电源插座(TDC Power supply lightning protection socket series) 产品介绍 Product introductionTDC系列插座式电源电涌保护器依据IEC标准设

54、计。用于设备端 D级防雷保护，具有精细的防护性能，对于雷电过电压、电源过电压、电网闪变、电磁脉冲均有良好的防护。插座式配置将电涌保护器与电源插板完美结合，RFI/EMI滤波电路及级间协调电感，可吸收射频/电磁干扰等线路电涌，延长设备正常工作寿命，降低长期运行成本。TDC series socket power SPD according to IEC standard design. D-level lightning protection for the device-side,With a fine protective performance, The lightning over vo

55、ltage, overvoltage, grid flicker, have good protection of electromagnetic pulse. Outlet configuration will be a perfect combination SPD and power strip, RFI / EMI filtering circuits and interstage coordination inductance, Can absorb radio frequency / electromagnetic interference and other line surgesExtend the normal working life, Reduce lo