航发pcf1报告全尺寸.part1measured report

1、trpeo Rde usrae myl ul11S_CFNt ce orj P11SeC:ma r b:e umNtr a Pr b:e umNDAC61- 8074000TVCDORP- NAEe G:ma NtordPucQIAOrFEN:NGANJING: drs danat sl air et a MCCV:l air et a Ml utac A mss0m1: k. cnieh TLA042RC- 932ADVLA042RC:sskcnieht nigt ao C6 11/2:e01mi6tn/oit cet e D检查结R果ESULCTHECKDATECHECK检测日期OK.RA

2、TIO2016/11/6Part codeP1P2P3TOTAL全尺寸OK Ratio128sPoOK128TotalsPo100%SURF.型面OK Ratio79sPoOK79TotalsPo100%TRIM修边OK Ratio45sPoOK45TotalsPo100%HOLE孔位孔径OK Ratio4sPoOK4TotalsPo100%ornIfSP Roint a m6Y/4X1Z5X3Z2ZCADFILD:CVT00004708NomActDevLwTolUpTolTrendRationalDMIS(TM) External-Array Software, IncPage 1 -D3

3、792 RationalDMIS(TM) External-Array Software, IncPage 2 -D3792 RationalDMIS(TM) External-Array Software, IncPage 3 -D3792 RationalDMIS(TM) External-Array Software, IncPage 4 -D3792 RationalDMIS(TM) External-Array Software, IncPage 5 -D3792 RationalDMIS(TM) External-Array Software, IncPage 6 -D3792 R

4、ationalDMIS(TM) External-Array Software, IncPage 7 -D3792 RationalDMIS(TM) External-Array Software, IncPage 8 -D3792zi se olHnigkc heeC0RPS12 1RPS安2装安孔装孔n1o2m.i1n1a2l.81.*018 8.0a1c2t.u1a9l818.23812.23*8.81.01818.09d8eviation0.130.2380.01.01818nominalactualdeviation孔2s1s孔安装 1pRpR安装 2nig nnhiTmmreque

5、st:thic%ngCHECKIRNEGPORTTHINNESkneMsesasuremmthicknaecstsual2:0%MAX LIMITSTNhOinAncituNaolrmal11.00.946.00%3524121.00.937.00%31.00.8713.00%41.00.955.00%51.00.946.00%67891011121314MAXTHINNING13.0%Appearance CheckingAppearance Checking 外观检查NO判定标准 Control standard检验方法 Methond判定 OK、NG、N/Apicture1零件是否正确？

6、 Is the rignt part?Visual目视OK2是否有开裂、暗裂？No crack,deformationVisual 目视OK3毛边、毛刺、尖角是否 0.3mm范围内？ glitches, indenion,damaged,Venirecaliper游标卡尺OK4是否有模痕、压伤（无手感可接受）？ No roughness detect with the handwith the handOK5是否有拉伤、划伤？No degradation or deformation手触with the handOK6是否有起皱、变形（装配面平面度需0.2MM以内）？No crack,deformationVisual /Venire caliper目视/游标卡尺OK7是否有生锈？Rust?Visual 目视OK8字印是否正确、明显且无手感？ Marking information crrect ?Visual/ with the hand目视/手触OK9公差是否与3D公差相符？ Report tolerance is the same with 3D?检查 checkingOK10零件定位是否与检具定义相符？ PRS is the same with gauge?检具gaugeOK11料边断差是否超过公差带的50%？ Trim no mor