文本教案讲稿en

1、Determining the value to be set for $CURR_MON with external axesBackground:If the value of $CURR_MON is set too low, acknowledgement message 1241 is generated:ixt monitoring, current limit of the motor cable E1 after 60 s exceeded 100%In such a case, the current r.m.s. value must be calculated from

2、the complete program cycle time (incl. wait times). The oscilloscope trace function is used for this. Holding currentREAL $CURR_MON12;PERMISSIBLE HOLDING CURRENT DEFINES THE LIMIT FOR THE I2t MONITORING AT 55 C (CABLE WARMING!)$CURR_MON1=7.3$CURR_MON2=7.3$CURR_MON3=2.7$CURR_MON4=2.0$CURR_MON5=2.0$CU

3、RR_MON6=2.0$CURR_MON7=9.3$CURR_MON8=12.8$CURR_MON9=6.7$CURR_MON10=0.0$CURR_MON11=0.0$CURR_MON12=0.0Permissible limits:Peak current: 2 sHolding current:60 sMotor I0 (r.m.s.)KK67Y26.9 AKK65Y19.7 A1FK610012.8 A1FK6081 6.7 AKK53Y 6.7 AKK55Y12.8 AKK4EY 2.7 AMotor typeA0ABCCC0D1FK7060 2.7 AD01FK7032 1.7 A

4、1FK7034 2.0 A1FK7081 9.3 AEE0HProcedureMethod:The system executes complete production cycles (incl. wait times) until a minimum time of 60 seconds has elapsed. During this time, the current of the axis concerned is recorded in the trace.The value of $CURR_MON for the relevant axis is to be set to a

5、higher value, than the determined r.m.s. value.Test programData list for test programAutomatic start of the oscilloscope function by means of program commandsStart of the recordingAutomatic adaptation of the nameAutomatic end of the recordingEnd of the trace recordingSettings for the oscilloscope tr

6、ace function (1)Settings for the oscilloscope trace function (2)Trace recording the current over 6 cycles in 90 sSelection of the area for calculation of the r.m.s. valueDisplay of the r.m.s. valuer.m.s. value: 4.78 from 11.70 to 89.99 sRMS (effective value: 4.78 von 11.7 bis 89.99)Trace settings fo

7、r axis E1 (1)Monitor Diagnosis Oscilloscope ConfigureAssign name to traceEnterTrace length min. 60 sEnterEnterUse the UP and DOWN arrow keys to select the trigger condition Trigger on motion startDeactivate the NUM functionPress TAB to access the DSE cardUse the UP and DOWN arrow keys to select DSE

8、2Press TAB to access the I/O groupUse the UP and DOWN arrow keys to select No I/O dataSoftkey DSE Tab.Trace settings for axis E1 (2)Use the UP and DOWN arrow keys to position the cursor on the actual current of axis E1Mark this by pressing the space barSoftkey MainSoftkey SavePress softkey Start unt

9、il the trace status #T_WAIT is displayedRun programWait until trace status #T_END is displayedSoftkey ShowSoftkey InfoCurves that are not required can be removed from the display by pressing the Enter keySoftkey Info only the current curve is visibleRepeatedly press the softkey until the softkey RMS appearsPress the softkey RMSTrace settings for axis E1 (3)Use the left arrow key to mark the start of the area for which evaluation is to be carried outEnterUse the right arrow key to mark the end of the area for which evaluation is to be carried outEnterThe r.m.s.