整车开发通用英文缩写(仅限内部参考使用)

1、整车开发通用英文缩写（按首字母排序）,英文缩写（按首字母排序）,英文全称,中文含义100% Cal,100% Calibration ,100%标定100% IVER,100% Integration Vehicle Engineering Release,100%集成车工程发布100% PPAP,All parts at full PPAP for Vehicle program,为了整车项目，所有零件须完全通过PPAP100% SVER,100% Structure Vehicle Engineering Release,100%结构车工程发布65% Cal,65% Calibration

2、,65%的动力总成标定80% Cal,80% Calibration,80%的动力总成标定8D,8 Disciplines,问题解决8步法A,Alpha,Alpha阶段（动力总成产品开发的一个阶段）A MRD,Alpha Material Required Date,Alpha样件需求日期A/T,Automatic Transmission,自动变速器A/T,Automatic Transmission,自动变速器AA,Architecture Approval,架构批准AAM,Alliance of Automobile Manufactures,汽车制造商联盟ABS,Anti-lock B

3、rake System or Anti-Block Steering,防抱死制动系统AC,Architecture Confirmation,架构确认 ACE,Assistant Chief Engineer,总工助理ACT,Activity,工艺路线ACT BOM,Assembly Component Tree BOM,总成件树形BOMAD,Alternatives Development,主题开发ADV,Analysis / Development / Validation,分析/开发/验证ADV,Analysis, Development and Validation,分析，开发和认证A

4、E,Application Engineer,应用工程师AE,Application Engineer,应用工程师AEM,Assimilability evaluation method ,可装配性评估方法AFI,Architecture Framing Initiation,架构框架启动AIAC,Automotive Industry Action Group,美国汽车工业行动集团ALY,Alloy,铝合金AMT,Automatic Machincal Transmission,机械式自动变速器ANSI,American National Standards Institute,美国国家标准

5、协会AP,Advanced Purchasing ,提前采购AP,Assembly Plant,总装厂APB,Automotive Product Board,汽车产品委员会APD,Approved Product Description,批准的产品描述APE,Annual Program Execution,年度项目执行APEC,Asia Pacific Economic Cooperation,亚太经济联盟APQP/CP,Advanced Product Quality Planning and Control Plan ,先期产品质量规划和控制计划APSB,Asia Pacific St

6、rategy Board,亚太战略委员会（通用汽车的高层管理组织）AR,Appropriation Request,项目预算ARC,Architecture Refinement Complete,架构优化完成ASB,Automotive Strategy Board,汽车战略委员会（通用汽车的高层管理组织）ASC,经销商售后管理系统ASE,Automotive Safety Engineering,汽车安全工程ASE,Aftersales Engineering,售后工程ASN,Advanced shipping notice,发货通知单ASSI,Architecture Statement

7、 of Strategic Intent,战略意向的架构陈述Assy Check-in,Assembly Line Check-in,装配线进场启动现场安调Assy PPAP,Assembly Line PPAP,装配线通过PPAPAssy PPAP,Assembly Line PPAP ,装配线通过PPAPAssy PPV,Assembly Line Products and Process Validation,装配线交付后的产品工艺验证Assy PPV,Assembly Line Production and Process Validation,装配线交付后产品工艺验证Assy Run

8、-Off,Assembly Line Run-Off ,装配线试装交样日期Assy Run-off ,Assembly Line RUN-Off ,装配线整线打通，启动试装，允许手工装配Assy Run-off MRD,Assembly Line RUN-Off Material Requied Date ,装配线ATC,Auto Temperature Controller,自动空调控制器ATF,Automatic Transmission Fluid ,自动变速箱油ATT,Attachment,附件ATT ,Actual takt time,实际单件工时AVD,Advanced Vehic

9、le Development,先期车辆开发AVDC,Advance Vehicle Development Center,先期车辆开发中心AVD-LT,Advanced Vehicle Development-Leadership Team,前期整车开发-领导小组AVDP,Advanced Vehicle Development Process (Time between DSI and VPI),先期车辆开发流程（在DSI与VPI之间）AVPM,Advanced Vehicle Planning Manager,先期车辆计划经理B,Beta,Beta阶段（动力总成产品开发的一个阶段）B,Bu

10、ild,制造B MRD,Beta Material Required Date,Beta样件需求日期B+U,Building and Utility,土建公用BAD,Build Authorization Document,试制授权文档BC,Business Case,业务计划BCM,Body Control Module,车身控制器BDC,Body Distributon Central,车辆调配中心BESC,Base Engine Steering Committee,发动机总成战略转向委员会BIQ,Building in Quality ,制造质量BIR,Prototype Build

11、Issue Report,试制问题报告 BIR,Build Issues Resolution,试制问题BIR,Build Incident Report,装车问题报告BIR,Bulding issue report,造车问题报告BIW,Body-In-White,白车身BIW,Body in White,白车身BOD,Bill of Design,设计清单BOE,Bill of Equipment,设备清单BOM,Bill of Material,物料清单BOM,Bill of Material,物料清单BOM,Bill of Material,物料清单BOM,Bill Of Materia

12、l,物料清单BOM,Bill Of Material,物料清单BOM,Bill of Material,物料清单BOP,Bill of Process,工艺清单BOP,Bill Of Process,工艺清单BP,Break Point,断点BPD,Business Plant Deployment,业务计划实施BPP ,Best people practices,最佳人员准则BPR ,Business plan recompose, 业务流程重组BS,Body Shop,车身车间BSD,Build Site Direction,试制现场指导书BUFFER,Buffer,线边缓存区C/CAP,

13、Construction/Conversion and Acceleration Plan,土建/改造和生产提速计划CAB ,Change Approval Board,更改审批会CAC,服务热线专员CAFE,Corporate Average Fuel Economy,公司平均油耗Cal,Calibration,动力总成标定CARE,Customer acceptance review evaluation,整车报交检查CARE,Customer Acceptance & Review Evaluation,用户接受度和审查评估CC,Concept Confirmation,验证概念CC,C

14、onsolidation Center,集散中心CC,Confirmation Clinic,确认临床Cert LSO,Certification Lift Stop Order,通过排放认证通知CET,Cold Environment Test,寒区试验CH,Chassis Department,底盘部CI,Concept Initiation,提出项目概念CIM,Customer Interface Manager,客户服务经理CIP,Continue Improve Process,持续改进CIP ,Continue Improve Process,持续改进CIT,Continuous

15、Improvement Team,不断改进小组CIT,Compartment Integration Team,车厢集成小组CMC,Container Management Center,空箱管理中心CME,Change Management Engineer,更改管理工程师Cmk,N/A,临界机器能力指数Cmk,Capability Machine Index,机器设备能力CMM,三坐标测量C-NCAP,China New CAR Assessment Process,中国标准新车评估体系COC,Centre of Competence,能力中心COE,Center of Expertise

16、,经验总结中心CP,Control Plan,控制计划CPIT,Current Product Improvement Team,现有产品改进小组Cpk,Complex Process Capability,过程能力指数Cpk,Process Capability Index,稳定过程的能力指数CPQE,Current Product Quality Engineer,现有产品质量工程师CPV ,Cost per Vehicle ,单车成本CR/DN,Change Request / Decision Notice,更改决议CR/DN,Change Request/Decision Notic

17、e,变更申请/决议通知CRB,Change Review Board,更改评审小组CS,Contract Signing,动力总成签署项目合同CS,Contract Signing, 合同签订CS1,Controled Shipping 1,一级受控发运CS2,Controled Shipping 2,二级受控发运CSC,Controls Steering Committee,控制模块战略转向委员会CSI,Customer Satisfaction Index,用户满意度指标CSI,Customer Satisfaction Index,售后满意度CSN,Current Sequence Nu

18、mber,流水号CSO,Contract Sign-Off ,合同签署CSO,Contract Sign-Off (VDP),整车签署项目合同（VDP术语） CSO HC,Contract Sign-Off Health Check,合同签署健康检查CSO HC,Contract Sign-Off Health Check,合同签署健康检查CT,Cycle Time,制程周期CT,Cycle time ,周期时间CT,Creativity Teams,创造性工作小组CT,Critical Test,关键试验CTS,Component Technical Specification,零部件技术标

19、准CTT,Common Timing Template,标准2级进度模板CVER,Concept Vehicle Engineering Release,概念车工程发布CVER LL,Concept Vehicle Engineering Release Long Lead,概念车工程发布长周期CVIS,Completed Vehicle Inspection Standards,整车检验标准CVQC,Completed vehicle quality ceter,整车质量中心CVQCB,Completed vehicle quality ceter board,整车质量目视板CVT,Cont

20、inuously Variable Transmission,无级变速器D.Q.R,合格率概况DAS,Design & Analysis Section,设计分析科DC,Deliver Charter,递交项目章程DCN,Design Change Notice,设计更改通知DCN,Design Change Notice,设计更改通知DCP,Dimension Control Plan,尺寸控制计划DCS,Design Concept Sheet,概念设计表DCT,Double Clutch Transmission ,双离合器变速箱DD,Direct Delivery,直接投线DDSP,D

21、river Door Switch Pack,驾驶席门控开关DEI,Die Engineering Integration,模具工程集成DFA,Design for Assembly,装配工艺性设计DFM,Design for Manufacturability,制造工艺性设计DFMEA,Design failure mode and effects analysis,设计失效模式和效果分析DFMEA,Design FMEA,设计失效模式分析DIFF,Differential,差速器DL 3b,Design Level 3b,设计阶段3bDMS,Dealer Manage System,经销商

22、管理系统DOL,Dealer On Line,经销商在线系统DP,Demand Plan,需求计划DPV,Defects per vehicle,单车缺陷数DPV,Defect per Vehicle,单车缺陷数DQ&V,Design Quality & Validation,设计质量和验证DR,Direct run,直接通过率DRC,Design Review Committee,设计评审委员会DRE,Design Responsible Engineer,设计和发布工程师DRE,Design Release Engineer ,设计发布工程师DRE,Design release engin

23、eer,设计发布工程师DRL,Direct run loss,直接通过损失率Drop Off,Drop Off,停产DS44,HIGH SPEED DURABILITY TEST,高速耐久试验（MGRES 标准）DSG,Direct shift gearbox,双离合器变速箱DSI,Document of Strategic Intent ,战略意向书 DSM,Driver Seat Module,驾驶席座椅控制模块DSO,Design Sign Off,设计签署DTA,Design Theme Alternatives,设计主题选项DTC,Diagnostic Trouble Code,诊断

24、故障码DV,Design Validation,设计验证DV,Design Validation,产品设计验证DVP,Design Validation Plan,设计验证计划DVT,Dynamic vehicle test,整车综合动态测试E/T/C,Engine/Transmission/Controller,发动机/变速器/控制模块EBA,Emergency Brake Assistant,紧急制动辅助系统EBD,Electronical Brake Distribute,电子制动力分配系统EBOM,Engineering BOM,工程BOMEC,Embedded Controller,

25、控制模块ECC,ERP Central Component,ERP核心组建ECR,Engineering Change Request,工程更改请求ECR,Engineering Change Request,工程更改请求ECR,Engineering Change Request,工程更改申请ECR,Engineering Change Request,工程项目变更申请ECS,Engineering Change Summary,工程变更摘要ECT,Emission Control System,电子控制自动变速器EDS,Electronic Data Systems,电子数据系统EEVC,

26、European Enhanced Vehicle-Safety Committee,欧洲提高车辆安全性委员会EFEO,Emissions & Fuel Economy,排放和燃料经济EGM,Engineering Group Manager,产品工程小组经理EI&S,Electronics Integration & Software,电器零件集成和软件ELV,End of life vehicle,整车寿命结束EMlS,Emission,排放EMS,Engine Management System,发动机管理系统ENB,Build-Test Section,试制试验科E-NCAP,Euro

27、 New Car Assessment Process,欧洲标准新车评估体系ENG,Engineer,工程师EOA,End of Acceleration,生产提速的完成EOLT,End of Line Test,生产线试验结束EP,Engineering Prototype ,工程样车（件）EPA,Environmental Protection Agency,环境保护厅EPC,Engineering Program Committee,工程项目委员会EPN,Engineering Project Number,工程项目数目ERD,Early Requirement Document,早期的

28、要求文件ESB,European Strategy Board,欧洲战略委员会（通用汽车的高层管理组织）ESO,Engineering Sign Off,发动机整机工程签署ESO,Engineering Sign Off,工程签署ESO,Engineering Sign-off,工程签署ET,Engineering Technology,工程技术EV,Engineering Vehicle,工程样车EWO,Engineering Work Order,工程工作指令EWO,Engineering Work Order,工程更改号EWO,Engineering workorder,工程更改流程Ex

29、p Cal,Experimental Calibration,尝试性标定FA,Final Approval,批准正式生产FAC,集团销售经理FATG,Final Approval to Grain,生产最终批准FBIW,First Body in White Complete,第一轮白车身完成FE,Functional Evaluation,功能评估FE LSO,Fuel Economy Label Lift Stop Order,通过油耗认证的通知FIVC,First Integration Vehicle Complete,第1辆集成车制造完毕FIVC,First Integration

30、Vehicle Complete,第一轮集成车完成FLO,Factory Layout,工厂布局FM,功能尺寸FM,Finance Manager,财务经理FMC,First Mule Complete,第一轮骡子车完成FMC,区域售后支持FMEA,Failure model effectiveness analysis,失效模式分析FMEA,Failure model effectiveness analysis,失效模式分析FMEA,Failure Mode and Effects Analysis,潜在失效模式及后果分析FMEA,Failure mode and effects anal

31、ysis ,失效模式和后果分析FMEA,Failure Mode and Effect Analysis,失效模式和影响分析FMS ,Flexible manufacturing systems ,柔性制造系统FMVSS,Federal Motor Vehicle Safety Standards,联邦汽车安全标准FPPV BIW,First Product/Process Body in White Complete,第一轮产品/工艺白车身完成FPPVC,First Product/Process Validation Vehicle Complete,第一轮产品/工艺验证车辆完成FPS,F

32、ixed Point Stop,固定停止位置FTC,First Time Capability,首次能力FTP/FTQ,First time pass/quality,一次通过合格率FTQ,First time quality ,下线合格率FWD,Four Wheel Drive,四轮驱动G,Gamma,Gamma阶段（动力总成产品开发的一个阶段）G MRD,Gamma Material Required Date,Gamma样件需求日期G/L,Group leader,工段长GA,General Assembly ,总装GA,General Assembly,总装GADT,Global Ar

33、chitecture Development Team,全球架构开发小组GBOM,Global Bill of Material,全球物料清单GMNA,General Motors North America,通用汽车北美分部GMPT,General Motors Powertrain,通用汽车动力总成分部GPDC,Global Product Development Council,全球产品开发理事会GPDP,Global Powertrain Development Process,全球动力总成开发流程GPDS,Global Product Description System,全球产品管

34、理系统GSD,Global Segment Director,全球细分主管GSS,Global Sales and Service,全球销售和服务GVDP,Global Vehicle Development Process ,全球整车开发流程GVDP,Global Vehicle Development Process,整车开发流程GVDP,Global Vehicle Development Process,整车开发流程GVDP,Global Vehicle Development Process ,全球汽车开发流程GVDP,Global Vehicle Development Proce

35、ss,全球整车开发流程GVDP,Global Vehicle Development Process,整车开发流程GVLE,Global Vehicle Line Executive,整车平台执行GVW,Gross Vehicle Weight,车辆总重GW,Gateway,网关HET,Hot Environment Test,热带试验HRC,Hardware Release Center,硬件发布中心ICD,Interface Control Document,接口控制文件IDR,Initial Data Release ,初始数据发布IDSR,Integration Driven Subs

36、ystem Requirement,集成驱动子系统要求ILP,Inbound Logistic Planning,入厂物流规划IMES,Integration Manufacturing Executive System,生产执行系统Initial Cal,Initial Calibration,初始标定IOM,Inspection operator method, 检验操作方法IOS ,Inspection operator summary,检验操作概要IPPE,integrated Product and Process Engineering,集成产品与工艺工程IPTV,Incident

37、 per Thousand Vehicles,每千辆车的故障率IPTV,Incidents Per Thousand Vehicles,每一千台车事故率IPTV,Incidents Per Thousand Vehicles, 每千辆车的故障率IPTV,Incidents Per Thousand Vehicles,千辆车故障率IR,Incident Report , 事故报告IRP,Issue Resolution Process,问题解决流程IRR,Internal Rate of Return ,内含报酬率ISO,International Standard Organization,国

38、际标准化组织IV,Integration Vehicle,集成车IV MRD,Integration Vehicle Material Required Date,集成车的物料需求日期IVBR,Integration Vehicle Build Readiness Review,集成车制造准备评审IVER,Integration Vehicle Engineering Release,集成车工程发布JIS,Just In Sequence,排序供货JIS,Just In Sort,供应商排序供货方式JIS,Job Instruction Sheet,岗位指导书JIT,Just In Time,

39、及时供货JIT,Just In Time,供应商及时供货方式JPH,Job per Hour,生产节拍JRS,Joint Ride Session,联合评审JSC,生产采购委员会JSC-GP,Joint Sourcing Committee - General purchase,联合采购委员会-一般采购Kcc,Key Control Characteristic,关键过程控制特性KCC,Key Control Character,关键控制特性KCDS,Key Characteristic Designation System,产品关键特性定义系统KO,Kick-Off,启动Kpc,Key Pr

40、oduct Characteristic,关键产品特性KPC,Key Product Characteristic,关键产品特性KPC ,Key product characteristic,主要产品特性KPC ,Key product characteristic,主要产品特性KPC ,Key process control ,关键过程控制KPC ,Key process control,关键过程控制LAAMSB,Latin America, Africa, Middle East Strategy Board,通用的拉美，非洲，中东战略委员会LCL,Lower Control Limit

41、,管制下限LCS,Logistic Confirmation Sheet,物流确认单LL,Learning Loop,学习周期LL,Long Lead,长周期LLPR,Long Lead Production Release,长周期的产品发布LM,Launch Manager,启动经理LOU,Line of Usage BOM,整车BOM行LSL,Lower Specification Limit,规格下限LSP,Lean sales and marketing prograne,精宜营销LTR,Launch Team Release,启动小组释放LWO,Logistic Work Order

42、,物流属性更改号M+E,Machine & Equipment,机器设备MAC,区域经理MBOM,Manufacturing BOM,制造BOMMDS,Materiel Data Sheet,物料数据单ME,Manufacture Engineer,样车试制工程师或生产线制造工程师ME,Machine and Electronic,电器设备ME,Manufacturing Engineering,制造工程ME,Manufacturing Engineering,制造工程MEC,区域市场支持MEIS,Manufacturing Engineering Info System,制造工程信息系统ME

43、S,Manufacturing Execution System,制造执行系统MES,Manufacturing Execution System,制造执行系统MFG Site Dec,Manufacturing Site Decision,确定生产厂址MIC,Marketing Information Center,市场信息中心MILKRUN,Milkrun,循环取货MKT,Marketing,营销MMR,Manufacturable Math Release,制造数模发布MO,Manufacturing Operations,生产管理部门MP OTS 100%,100% Made Part

44、s in OTS,100%自制件达到OTS状态MP OTS 100,100 Made Parts in OTS,100%自制件达到OTS状态MP PPAP,Made Parts PPAP,自制件通过PPAPMP PPAP,Made Parts PPAP,自制件通过PPAPMP PPV,Made Parts Production and Process Validation,自制件生产线交付后的产品工艺验证MP PPV,Made Parts Production and Process Validation ,自制件生产线交付后的产品工艺验证MPS,Master Planning System,

45、主计划系统MPV,Multi-Purpose Vehicle,多用途轿车MR,Manufacturing Requirements,制造要求MRD,Material Required Date,交样日期MRD,Material Requirement Date,物料需求日期MRD,Material Required Date (for physical builds),物料需求日期（用于制造样机）MRD,Math Required Date (for virtual builds),数模需求日期（用于虚拟制造）MRE,Manufacturing Responsible Engineer,制造工

46、程师MS,Manufacturing Studies,制造车间MSA,Measurement System Analysis,测量系统分析手册MSA,Measurement System Analysis,测量系统分析MSA,Measure System Analyse,测量系统分析MSA,Measurement system analysis ,测量系统分析MSS,Market Segment Specification,市场细分规范MSS,区域销售支持MSS,Market Segment Specification,市场分割规范MT,Manual Transmission,手动变速箱MT&

47、E,Machines, Tools and Equipment,机床，工装和设备MTS,Manufacturing Technical Specification,制造技术标准MVB,Manufacturing Validation Build,用于认证制造工艺的整车制造MVB,Manufacturing Validation Build,制造验证造车MVB (ns) ,Manufacturing Validation Build (non saleable) ,用于认证制造工艺的整车制造（不可销售的）MVB (s) ,Manufacturing Validation Build (salea

48、ble) ,用于认证制造工艺的整车制造（可销售的）MVBns,Manufacturing Validation Build Non-Salable,非销售制造验证造车MVBs,Manufacturing Validation Build Salable,销售制造验证造车MVSS,Motor Vehicle Safety Standards,汽车安全标准MWO,Manufacture Work Order,制造属性更改号MY,Model Year,年度款MYM,Model Year Manager,车型年经理NAO,North American Operations,通用的北美分部NEO,New

49、 Employee Orientation,新员工培训NOA,Notice of Authorization,授权书NOD,Notice of Decision,决议NOD,Notice of Decision,决议通知NPV,Net Present Value,净现值NRD,Normal Road,一般公路NSB,North American Strategy Board,通用的北美传略委员会（通用的高层管理组织）OBD,On Board Diagnostics,车载诊断系统OEM ,Original Equipment manufacturers ,原始设备制造商（主机厂）OEM Run-

50、Off,Original Equipment Manufacturer Run-Off,零件供应商工装设备具备试生产条件OEM Run-off ,Original Equipment Manufacturer Run-off ,零件供应商工装设备具备试生产条件OJT,On Job Training,在岗培训OPO,Office of Product Operations,产品高层管理组织ORS,Occupant Restraint System,乘员约束系统OT,Overtime,加班OTD,Order to Delivery,订单到货时间OTP,On Time Performance,及时性

51、能OTS,装车评审OTS,Off-tool Sample,工装样件OTS,Off-tool Sample,工装样件OTS,Off-tool Sample,工装样件OTS ,OFF-TOOL-SAMPLE,工装样件OTS QV,OTS Quality Valve,OTS质量阀OTS交付状态满足质保的开阀要求OTS QV,OTS Quality Valve,OTS质量阀，OTS交付状态满足质保的开阀要求OTS TG2,Off Tooling Samples Tooling Go Level 2,OTS设计达到TG2阶段，发布图纸用于供应商启动工装和设备投入OTS TGL2,Off Tooling

52、Samples Tooling Go Level 2,OTS设计达到TG2阶段P,Pilot,批量试生产P,Pilot,小批量生产PA,Production Approval,批准正式生产PA,Program Administrator,项目管理专员PaC,Physical Alpha for Customer,提交客户的Alpha样机PACK,Packaging,包装规划PAD ,Product Assembly Documentation ,产品装配文件PAM,Product Assemble Manual,样车装配指南PAM,Product Assemble Manual,产品装配手册P

53、APIR,Product and Process Integration Review,产品和工艺集成会议PAS,Packaging Approval Sheet,包装确认单PAS,Parking Aid System,泊车辅助系统PAS,Parking Aid System,泊车辅助系统PbC,Physical Beta for Customer,提交客户的Beta样机PBS,Painted Body Store,油漆车身存储区PC,Deliver Pilot to Customer,向客户提交Pilot产品PC,Pullcord,拉环PC,Problem Communication,问题信

54、息PC&L,Production Control and Logistics,PC&L部门（GM的一个部门）PCL,Production Control Manager,生产控制与支持PCM,Powertrain Control Module,动力总成控制模块PCM ,Process Control Manager,工艺控制负责人PCN,Project Cost Change Notice,项目更改通知单PCN,Project Costbook Change Notice,项目Costbook更改通知单PCR,Problem communication report ,问题交流报告PCR,Pr

55、oblem communication report,问题交流报告PCR,Problem Communication Report,问题交流报告PCR,Problem Communication Report,问题交流报告PDC,Parking Distance Control,泊车距离控制PDC,Parking Distance Control,泊车距离控制PDCA,Plan、Do、Check、Action,计划、实施、检查、行动PDCA ,Plan-Do-Check-Action ,计划,实施,检查,行动PDI,Product delivery inspection,产品交付检查PDI,P

56、reliminary Data Indicator,初步数据指示器PDI,Pre-delivery Inspection,车辆行运“零公里”检查报告PDS,Product Data Structure,产品数据结构，在SCM中用到的数据对象，集成了BOM、工艺和工厂布局信息PDT,Product Development Team,产品开发组PDT,Product Development Team,产品开发小组PDT,Product Development Team,产品开发小组PDT,Product Development Team,产品开发小组PDT ,Product Development

57、 Team ,产品开发小组PE,Product Engineering,产品工程PET,Program Executive Team,项目执行小组PET,Program Execution Team,项目组PET,Program Execution Team,项目执行小组PFI,Program Framing Initiated,项目框架启动 PFMEA,Process failure mode and effectsanalysis,过程失效模式和后果分析PFMEA,Process FMEA,工艺失效模式分析PFMEA,Process failure mode & effects analy

58、sis,过程失效模式分析PFSE,Product Focus Systems Engineer,产品系统工程师PG3,Powertrain Gateway,关键里程碑节点PgC,Physical Gamma for Customer,向客户发运Gamma样机PGM,Program Management / Project Management,项目管理PGM,Program Management,项目管理PGM ,Program Management ,项目管理Pilot,Pilot,试生产Pilot,Pilot,试生产Pilot QV,Pilot Quality Valve,试生产质量阀满足

59、启动试生产的开阀要球Pilot MRD,Pilot Material Requied Date,Pilot交样日期Pilot MRD,Pilot Material Required Date,Pilot的物料需求日期Pilot QV,Pilot Quality Valve,试生产质量阀满足启动试生产的开阀要求PIM,Powertrain Interface Manager,动力总成接口经理PLM,Production Launch Manager,生产启动经理PLP,单车利润表PM,Programme Manager,项目工程经理PM,Program Manager,项目经理PM,Progra

60、m Manager,项目经理PM,Plan maintain,计划维护PM,Prevention Maintenance,预防性维护PM ,Program Manager,项目经理PMO,Program Management Office,项目管理办公室（通用的一个部门）PMP,常规尺寸PMT,Product Management Team,产品管理小组PN,Part NO.,零件号PP,Pre-pilot,前期试生产PP,Pre-Pilot,预试生产PP,Pre-pilot,试生产P-P,Pre-Pilot,试生产PP PPAP,Purchased Parts Production Part