30种常用塑料工艺参数参照表

,,,,,,,,30种常用塑料工艺参数表,,,,,,,

1,材质：,ABS,密度g/cm3:,1.07,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度mm/s,螺丝速度（最佳）mm/s

,0.1-0.4,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,120~200,30~70,10~50,0.30,1.00,高速,550

,0.5-0.9,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,120~200,30~70,10~50,0.30,1.00,高速,550

,1.0-1.5,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,100~140,30~70,10~50,0.78,3.31,中速,550

,1.6-2.2,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,100~120,30~70,10~50,1.74,6.68,中速,550

,2.3-3.4,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,80~100,30~70,10~50,4.02,15.46,中速,550

,3.5-5.0,210~230,220~230,210~220,200~210,50~60,50~70,100~110/1~2,80~100,30~70,10~50,8.80,30.23,低速,550

,备注：,一般壁厚1.5~5mm，流长比为80~100：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

2,材质：,ASA,密度g/cm3:,1.06,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,0.20,0.70,较高,600

,0.5-0.9,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,0.50,1.75,较高,600

,1.0-1.5,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,2.40,8.40,较高,600

,1.6-2.2,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,3.00,10.50,较高,600

,2.3-3.4,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,5.50,19.25,较高,600

,3.5-5.0,220~240,220~250,220~250,200~230,50~60,60~90,80~90/3~4,80~120,30~60,10~50,7.80,27.30,较高,600

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

3,材质：,CA,密度g/cm3:,1.28,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,180~220,185~225,175~210,160~190,40~60,50~80,60~70/2~3,70~90,30~80,5-100,0.50,1.50,快速,600

,0.5-0.9,180~220,185~225,175~210,160~190,40~60,50~80,60~70/2~3,70~90,30~80,5-100,0.50,1.50,快速,600

,1.0-1.5,180~220,185~225,175~210,160~190,40~60,50~80,60~70/2~3,70~90,30~80,5-100,1.39,4.18,快速,600

,1.6-2.2,180~220,185~225,175~210,160~190,40~60,50~80,60~70/2~3,70~90,30~80,5-100,2.71,8.14,慢速,600

,2.3-3.4,180~220,185~225,175~210,160~190,40~60,50~80,60~70/2~3,70~90,30~80,5-100,6.26,18.79,慢速,600

,3.5-5.0,180~220,185~225,175~210,140~160,40~60,50~80,60~70/2~3,70~90,30~80,5-100,13.79,41.37,慢速,600

,备注：,流长比一般等级约为300：1，易流动级为400：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

4,材质：,CAB,密度g/cm3:,1.20,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,0.43,1.30,快速,600

,0.5-0.9,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,0.43,1.30,快速,600

,1.0-1.5,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,1.31,3.93,快速,600

,1.6-2.2,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,2.53,7.59,慢速,600

,2.3-3.4,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,5.82,17.47,慢速,600

,3.5-5.0,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,30~140,20~70,5-100,12.78,38.35,慢速,600

,备注：,流长比一般等级约为300：1，易流动级为400：1.可流入较薄的部位。,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

5,材质：,CP,密度g/cm3:,1.21,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,0.20,0.70,快速,600

,0.5-0.9,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,0.50,1.75,快速,600

,1.0-1.5,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,2.40,8.40,快速,600

,1.6-2.2,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,3.00,10.50,慢速,600

,2.3-3.4,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,5.50,19.25,慢速,600

,3.5-5.0,180~200,185~205,170~190,140~160,40~60,20~80,60~70/2~3,50~210,30~80,5-100,7.80,27.30,慢速,600

,备注：,流长比一般等级约为300：1，易流动级为400：1.可流入较薄的部位。,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

6,材质：,EVA,密度g/cm3:,0.93,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,0.20,0.70,中速,500

,0.5-0.9,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,0.50,1.75,中速,500

,1.0-1.5,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,2.40,8.40,中速,500

,1.6-2.2,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,3.00,10.50,中速,500

,2.3-3.4,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,5.50,19.25,中速,500

,3.5-5.0,160~200,180~200,160~180,140~160,40~60,20~60,40~60/1~,60~150,35~70,10,7.80,27.30,中速,500

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

7,材质：,LCP,密度g/cm3:,1.40,？,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,0.20,0.70,中、高速,150

,0.5-0.9,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,0.50,1.75,中、高速,150

,1.0-1.5,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,2.40,8.40,中、高速,150

,1.6-2.2,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,3.00,10.50,中、高速,150

,2.3-3.4,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,5.50,19.25,中、低速,150

,3.5-5.0,290~310,310~330,300~320,280~290,60~80,40~160,140~150/4~8,80~140,20~40,10~50,7.80,27.30,中、低速,150

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

8,材质：,PA11,密度g/cm3:,1.04,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,0.20,0.70,高速,400

,0.5-0.9,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,0.50,1.75,高速,400

,1.0-1.5,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,2.40,8.40,高速,400

,1.6-2.2,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,3.00,10.50,高速,400

,2.3-3.4,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,5.50,19.25,高速,400

,3.5-5.0,190~200,200~220,220~250,180~190,70~90,60~90,80~90/3~4,90~130,30~50,50~150,7.80,27.30,高速,400

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

9,材质：,PA12,密度g/cm3:,1.02,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,0.20,0.70,高速,400

,0.5-0.9,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,0.50,1.75,高速,400

,1.0-1.5,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,2.40,8.40,高速,400

,1.6-2.2,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,3.00,10.50,高速,400

,2.3-3.4,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,5.50,19.25,高速,400

,3.5-5.0,195~250,200~250,190~240,160~170,70~90,70~100,80~90/3~4,90~130,50~60,50~150,7.80,27.30,高速,400

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

10,材质：,PA6,密度g/cm3:,1.14,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,220~260,230~260,220~250,220~240,70~90,80~90,90~110/4~6,140~,30~50,50~150,0.33,1.00,高速,400

,0.5-0.9,220~260,230~260,220~250,220~240,70~90,80~90,90~110/4~6,140~,30~50,50~150,0.33,1.00,高速,400

,1.0-1.5,220~260,230~260,220~250,220~240,70~90,80~90,90~110/4~6,110~140,30~50,50~150,0.93,2.79,高速,400

,1.6-2.2,220~260,230~260,220~250,220~240,70~90,80~90,90~110/4~6,110~140,30~50,50~150,1.79,5.37,高速,400

,2.3-3.4,220~260,230~260,220~250,220~240,70~90,20~40,90~110/4~6,80~110,30~50,50~150,4.12,12.37,高速,400

,3.5-5.0,220~260,230~260,220~250,220~240,70~90,20~40,90~110/4~6,80~110,30~50,50~150,9.04,27.13,高速,400

,备注：,壁厚大于0.8mm，一般为1~3.2mm。流长比为150~200：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

11,材质：,PA66,密度g/cm3:,1.15,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,140~,40~50,5~10,0.33,1.00,高速,400

,0.5-0.9,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,140~,40~50,5~10,0.33,1.00,高速,400

,1.0-1.5,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,110~140,40~50,5~10,1.01,3.04,高速,400

,1.6-2.2,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,110~140,40~50,5~10,1.97,5.92,高速,400

,2.3-3.4,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,80~110,40~50,5~10,4.53,13.60,高速,400

,3.5-5.0,260~295,270~295,260~280,240~250,70~90,80,90~110/4~6,80~110,40~50,5~10,9.97,29.92,高速,400

,备注：,若壁厚为2mm，比例可有300至350：1；若厚1mm，比例约有180/250：1，但熔流必须一致。,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

12,材质：,PBT,密度g/cm3:,1.30,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,0.20,0.70,快速,300

,0.5-0.9,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,0.50,1.75,快速,300

,1.0-1.5,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,2.40,8.40,快速,300

,1.6-2.2,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,3.00,10.50,慢速,300

,2.3-3.4,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,5.50,19.25,慢速,300

,3.5-5.0,200~220,230~240,230~250,200~220,60~70,70~110,130~/3~4,80~120,30~50,10,7.80,27.30,慢速,300

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

13,材质：,PC,密度g/cm3:,1.20,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,250~320,290~320,270~300,250~280,80~90,100~120,120~/2~4,160~,40~70,6~15,0.30,0.80,高速,400

,0.5-0.9,250~320,290~320,270~300,250~280,80~90,100~120,120~/2~4,120~150,40~70,6~15,0.30,0.80,高速,400

,1.0-1.5,250~320,290~320,270~300,250~280,80~90,85~100,120~/2~4,120~150,40~70,6~15,0.76,3.27,中慢速,400

,1.6-2.2,250~320,290~320,270~300,250~280,80~90,85~100,120~/2~4,80~120,40~70,6~15,1.64,6.55,中慢速,400

,2.3-3.4,250~320,290~320,270~300,250~280,80~90,85~100,120~/2~4,80~120,40~70,6~15,3.82,15.10,中慢速,400

,3.5-5.0,250~320,290~320,270~300,250~280,80~90,85~100,120~/2~4,80~120,40~70,6~15,8.40,33.19,中慢速,400

,备注：,"PC溶体流长比为80-100：1，制品厚度一般不低于1MM，大都在1.5-5MM之间;

",,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

14,材质：,PEEK,密度g/cm3:,1.3,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,0.20,0.70,中高速,300

,0.5-0.9,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,0.50,1.75,中高速,300

,1.0-1.5,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,2.40,8.40,中高速,300

,1.6-2.2,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,3.00,10.50,中高速,300

,2.3-3.4,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,5.50,19.25,中高速,300

,3.5-5.0,360~400,380~410,370~400,350~380,80~95,160~170,150~/3~,100~150,50~700,50~100,7.80,27.30,中高速,300

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

15,材质：,PE-HD,密度g/cm3:,0.96,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,80～140,40~100,50~200,0.57,1.70,高速,750

,0.5-0.9,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,80～140,40~100,50~200,0.57,1.70,高速,750

,1.0-1.5,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,80～140,40~100,50~200,1.84,5.51,高速,750

,1.6-2.2,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,70~100,40~100,50~200,3.58,10.73,中速,750

,2.3-3.4,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,70~100,40~100,50~200,8.22,24.65,中速,750

,3.5-5.0,210~300,230~300,220~290,210~280,60~80,50~95,70~100/1~2,70~100,40~100,50~200,18.08,54.23,中速,750

,备注：,最小壁厚0.8mm，一般壁厚1~3.5mm，流长比为230：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

16,材质：,PEI,密度g/cm3:,1.35,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,0.43,1.30,高速,400

,0.5-0.9,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,0.43,1.30,高速,400

,1.0-1.5,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,1.12,3.35,高速,400

,1.6-2.2,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,2.22,6.65,高速,400

,2.3-3.4,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,5.07,15.21,适中,400

,3.5-5.0,325~400,320~405,310~395,300~330,80~90,100~175,150/3~4,70~150,30~70,400,10.80,32.41,适中,400

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

17,材质：,PE-LD,密度g/cm3:,0.92,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,80~100,30~75,50~200,0.60,1.80,快速,700

,0.5-0.9,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,80~100,30~75,50~200,0.60,1.80,快速,700

,1.0-1.5,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,80~100,30~75,50~200,2.01,6.02,快速,700

,1.6-2.2,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,60~80,30~75,50~200,3.89,11.66,中速,700

,2.3-3.4,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,60~80,30~75,50~200,8.94,26.82,中速,700

,3.5-5.0,185~250,210~250,200~240,190~230,60~80,30~45,70~80/1~2,60~80,30~75,50~200,19.59,58.77,中速,700

,备注：,最小壁厚0.8mm，一般壁厚1~3.5mm，流长比为280：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

18,材质：,PET,密度g/cm3:,1.35,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,250~260,260~270,260~280,240~260,70~80,50-70,130~/4~5,80~100,30~50,4~20,0.20,0.70,中高,250

,0.5-0.9,250~260,260~270,260~280,240~260,70~80,50-70,130~/4~5,80~100,30~50,4~20,0.50,1.75,中高,250

,1.0-1.5,250~260,260~270,260~280,240~260,70~80,50-70,130~/4~5,80~100,30~50,4~20,2.40,8.40,中高,250

,1.6-2.2,250~260,260~270,260~280,240~260,70~80,50-70,130~/4~5,60~80,30~50,4~20,3.00,10.50,中高,250

,2.3-3.4,250~260,260~270,260~280,240~260,70~80,140,130~/4~5,60~80,30~50,4~20,5.50,19.25,中高,250

,3.5-5.0,250~260,260~270,260~280,240~260,70~80,140,130~/4~5,60~80,30~50,4~20,7.80,27.30,中高,250

,备注：,易流动，Rynite含30%GF（熔胶温度302度，模温90度）为350：1；Rynite含45%GF（熔胶温度302度，模温90度）为250：1；,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

19,材质：,PMMA,密度g/cm3:,1.19,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,110~140,40~60,100~300,0.40,1.00,中速,350

,0.5-0.9,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,110~140,40~60,100~300,0.40,1.00,中速,350

,1.0-1.5,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,100~120,40~60,100~300,1.08,3.69,中速,350

,1.6-2.2,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,100~120,40~60,100~300,2.32,7.48,中速,350

,2.3-3.4,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,80~100,40~60,100~300,5.40,17.27,慢速,350

,3.5-5.0,200~250,220~250,210~240,200~230,50~60,40~80,80~90/3~,80~100,40~60,100~300,11.78,38.05,慢速,350

,备注：,一般壁厚1.5~5mm.若壁厚1mm，一般用途级的比例约为110至130：1；易流动级则可达到150至170：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

20,材质：,POM,密度g/cm3:,1.40,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,120~200,30~50,100~200,0.50,1.50,偏快,200

,0.5-0.9,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,100~130,30~50,100~200,0.50,1.50,偏快,200

,1.0-1.5,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,100~130,30~50,100~200,1.54,4.09,偏快,200

,1.6-2.2,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,80~100,30~50,100~200,3.34,8.36,中速,200

,2.3-3.4,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,80~100,30~50,100~200,7.78,19.31,中速,200

,3.5-5.0,185~220,185~215,185~200,170~190,60~70,90~120,80~90/2~4,80~100,30~50,100~200,17.10,42.43,中速,200

,备注：,一般壁厚1.5~5mm.一般用途等级有100至250：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

21,材质：,PP,密度g/cm3:,0.90,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,120~200,40~60,120~200,0.50,1.20,高速,750

,0.5-0.9,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,120~200,40~60,120~200,0.50,1.20,高速,750

,1.0-1.5,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,100~120,40~60,120~200,1.32,4.31,高速,750

,1.6-2.2,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,100~120,40~60,120~200,2.88,8.68,高速,750

,2.3-3.4,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,70~100,40~60,120~200,6.66,20.07,高速,750

,3.5-5.0,230~300,220~290,210~270,200~250,60~80,40~80,70~90/1~2,70~100,40~60,120~200,14.66,44.09,高速,750

,备注：,注：一般壁厚0.9~4mm，若壁厚1mm，高MFR可达340：1，普通的为230：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

22,材质：,PPO,密度g/cm3:,1.07,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,0.27,0.80,高速,400

,0.5-0.9,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,0.27,0.80,高速,400

,1.0-1.5,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,0.89,2.66,高速,400

,1.6-2.2,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,1.73,5.18,高速,400

,2.3-3.4,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,3.97,11.90,高速,400

,3.5-5.0,225~290,245~290,235~280,225~270,70~80,110~150,80~100/2~4,100~140,50~70,10~35,8.73,26.18,高速,400

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

23,材质：,PPS,密度g/cm3:,1.34,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,100~130,40~50,10~30,0.20,0.70,中低速,200

,0.5-0.9,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,100~130,40~50,10~30,0.50,1.75,中低速,200

,1.0-1.5,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,100~130,40~50,10~30,2.40,8.40,中低速,200

,1.6-2.2,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,80~100,40~50,10~30,3.00,10.50,中低速,200

,2.3-3.4,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,80~100,40~50,10~30,5.50,19.25,中低速,200

,3.5-5.0,310~320,310~320,300~310,290~300,70~80,120~150,150~170/1~3,80~100,40~50,10~30,7.80,27.30,中低速,200

,备注：,完全视乎等级、熔胶、模温而定，可达150：1（若壁厚1mm）。,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

24,材质：,PS,密度g/cm3:,1.05,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,120~150,40~100,50~100,0.30,1.00,快速,800

,0.5-0.9,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,120~150,40~100,50~100,0.30,1.00,快速,800

,1.0-1.5,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,80~120,40~100,50~100,0.78,2.90,快速,800

,1.6-2.2,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,60~80,40~100,50~100,1.74,5.94,快速,800

,2.3-3.4,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,60~80,40~100,50~100,4.02,13.73,快速,800

,3.5-5.0,210~280,210~250,180~230,150~180,40~60,20~70,70~80/1~2,60~80,40~100,50~100,8.80,30.15,快速,800

,备注：,一般壁厚1~4mm，流长比为200：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

25,材质：,PSU,密度g/cm3:,1.25,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,0.50,1.50,低速,150

,0.5-0.9,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,0.50,1.50,低速,150

,1.0-1.5,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,1.65,4.94,低速,150

,1.6-2.2,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,3.21,9.62,低速,150

,2.3-3.4,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,7.34,22.01,低速,150

,3.5-5.0,300~360,320~360,310~350,300~340,80~90,130~150,160/3~,100~140,40~50,10,16.14,48.42,低速,150

,备注：,壁厚大于1.5mm，由于此塑料的黏度及成形温度俱高，流长比自然小，若壁厚1mm，比例有60至120：1，加入玻璃纤维会使比例降至30：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

26,材质：,PTFE,密度g/cm3:,2.15,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,0.5-0.9,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,1.0-1.5,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,1.6-2.2,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,2.3-3.4,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,3.5-5.0,265~270,275~280,280~290,200~210,,100~160,,,,,,,,

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

27,材质：,PVC,密度g/cm3:,1.4,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,150~,60~80,40~60,0.50,1.50,中低速,150

,0.5-0.9,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,120~150,60~80,40~60,0.50,1.50,中低速,150

,1.0-1.5,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,120~150,60~80,40~60,1.40,4.21,中低速,150

,1.6-2.2,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,100~120,60~80,40~60,2.74,8.23,中低速,150

,2.3-3.4,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,100~120,60~80,40~60,6.33,18.98,中低速,150

,3.5-5.0,145~180,160~180,150~170,140~160,40~60,30~60,60~70/1~2,70~100,60~80,40~60,13.91,41.73,中低速,150

,备注：,如壁厚1mm，一般用途等级80至100：1，易流动可达200：1.,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

28,材质：,SAN,密度g/cm3:,1.08,,,,,,,,,,,

,,,,,,,,,,,,,,,,

,壁厚mm,温度,,,,,,,压力,,,,,速度,

,,喷嘴℃,前段℃,中段℃,后段℃,料口℃,模温℃,干燥/时间℃/hr,注射mpa,保压mpa,背压bar,保压s,冷却s,注射速度cm/s,螺丝速度mm/s

,0.1-0.4,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,0.50,1.00,中速,400

,0.5-0.9,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,0.50,1.00,中速,400

,1.0-1.5,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,1.40,3.63,中速,400

,1.6-2.2,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,2.74,7.33,中速,400

,2.3-3.4,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,6.33,16.94,中速,400

,3.5-5.0,180~190,200~210,180~200,170~180,30~50,45~75,80~100/2~4,100~140,40~50,50~150,13.91,37.27,中速,400

,备注：,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,

29,材质：,SB,密度g/cm3:,1.01,,,,,,,