下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、Ski1 Mate, Wearable Exoskelton Robot Yoji Umetani, Yoji Yamada, Tetsuya Morizono* Tetsuji Yoshida*, Shigeru Aoki* *To yo ta Technological Ins ti tu te 2-12-1, Hisakata, Tempaku-ku, Nagoya, 468-8511 Japan E-mail: 1-2-3, Shibaura, Minato-Ku, Tokyo 105-8007 Japan E-mail: ty spo.shimz.co.b . . *Shimizu
2、Corporation ABSTRACT A wearable exoskelton robot, Skil Mate, is a new concept that can assist skilled workers in power as well as in skill. Skil Mate is composed of servo mechanisms and haptic devices (tactile or slipping-off sensors/displays), so that it can follow the workers movement. Skil Mate i
3、s suitable for works under hazardous environment such as in space, under sea, etc. Goal of the project is to develop a prototype model of the wearable robot for a spacesuit, which consists of an upper torso assembly and a pair of arms with gloves. but these developments did not deal with the lack of
4、 sense at fingertips, which is necessary for skilled works. One of the solutions for these problems, the authors propose a new concept, Skil Mate, a wearable exoskelton machine for skilled workers. Skil Mate concept is not just for astronauts but for skilled workers under hazardous environments. In
5、this paper, Skil Mate concept and its application are introduced, and then prototype development for space suit is outlined. 2. FEATURES OF SKIL MATE 1. INTRODUCTION An Extra-vehicular activity (EVA) robot, Shuttle RMS, has carried out important tasks in space programs, and other EVA robots are unde
6、r development or under experiment for future EVA tasks. While the number of tasks for EVA robots will increase in the future, there exist inevitable tasks for astronauts. The astronauts need spacesuit to protect themselves from hazardous environment, such as vacuum, higldlow temperature, micro-meteo
7、roids, etc, Because, the space suit is pressurized in 1/3 of atmosphere, it becomes stiff by the tension of space suit fabrics. And, thick fabrics inhibit an astronaut from sensing objects to be handled. The major problems caused by the space suit are I: (i) Hand and shoulder fatigue. (ii) Lack of s
8、ense at fingertips. (iii) Restriction on range of motion. Research and developments for the first problem, especially finger metacarpophalangeal (MCP) joint fatigue, have been done as power assisted gloves 2134. Experimental results of these developments showed that the power assisted gloves could r
9、educe MCP joint torque, The Skil Mate is a generic name of a machine or a device that moves when the human wears it. And, it is a passive machine having non-autonomous intelligent response incorporated in the human intellectual operation system. Features of Skil Mate are as below. (1) It is to be wo
10、rn by a man of skill in case that he should unavoidably work to accomplish tasks as an expert under hazardous environments such as in space. Usually, the man who works under hazardous environment needs protection suit, for example, space suit on orbit or dry suit under the sea. And, these suits rest
11、rict the mans movement and increase his fatigue. Skil Mate allows the man to decrease muscle strain while he works. (2)It is exoskeletal structure to envelop the mans body and it does not restrict the mans movement on joint arrangement and on joint range of motion. Moreover, haptic receptors or sens
12、ors should be mounted as interfaces between the human body and the object to be handled in order to enhance task efficiency. Consequently, it looks like an anthropomorphic robot when it is worn. (3)It is controlled to follow in response to the mans 0-7803-5731-0/99/%10.00 01999 IEEE IV - 984 movemen
13、t. Its response must be quick enough as the worker has senses without wearing Skil Mate or attached nuisance for their action, supporting his skill as if he is in the most desirable circumstance for his work. And, as an optional function, it is an exoskeletal shell that allows the worker to protect
14、from hazards. The worker under hazardous environment will get benefits from Skil Mate with the protection shell. Skil Mate may be the inevitable work suit for the works in the environment such as under high water pressure, low temperature and radiation exposure. Even if the protection shell is so th
15、ick making human movement slow like a tire-fighting suit, powered Ski1 Mate will compensate its mass, inertia and stiffness by its servo system. Wearing Skil Mate is to feel wearing no clothes or no working suit at all. 3. SKIL MATE FOR EVA In November 1997, Dr. Doi, Japanese astronaut, got on board
16、 in space shuttle “Columbia”. By wearing a spacesuit, he made extravehicular activity (EVA) to two times. The first activity was the capture by handgrip of the Spartan satellite. The second were emission and recovery of the robot camera and the sum total activity hour of EVA exceeded 12 hours. (Figu
17、re 1) Figure 1. EVA (Japanese Astronaut Dr. Doi) NASDA Photo NO: DOI-141CD0494-053 6 The authors discussed EVA experience with Dr. Doi. And he pointed out the space suit problems as below : 11 (1) Hand fatigue: The space suit glove was stiff because of pressurization with 1/3 of atmosphere and the a
18、stronaut need more finger force to overcome the stiffness. Still more EVA tasks included frequent grasping motion, for instance, grasping the handrails for moving himself, grasping hand tools. He also mentioned that mainly thumbs, forefingers and middle fingers were used for grasping motion. (2) Dif
19、ficulty in complex and sensitive tasks with fingertips: Fingertips of the space suit glove were covered with rubber and this did not interface slipping nor holding sense. He carried out this kind of tasks mostly by using his vision not by his sense of the fingers. (3) Restriction of motion: The spac
20、e suit had one bearing joint at the shoulder and if shoulder movement was not along the bearing joint, shoulder muscles may fatigue. If there were two bearing joints at the shoulder, this problem will be improved. And, he added that waist and hip flex was poor and this made him difficult to see swit
21、ches at his chest. From above discussion, application of Skil Mate to the space suit will have following features. (a) Skil Mate provides forcehorque to the space suit joints to cancel the stiffness caused by the pressurization. Skil Mate also detects astronauts movement for servo mechanism. (b) Ski
22、l Mate detects/displays force, pressure and slip sense at the fingertips, which allow the astronauts to accomplish complex and sensitive tasks. 4. PROTOTYPE MODEL Development of the prototype model started in the summer 1998. In the FY, we focused on hardware design and assembly. This section shows
23、our project status of the prototype model development. Actuator McKibben artificial muscles have been adopted as one of actuators for Ski1 Mate. Major advantage of the actuator include: (1) larger powedweight ratio than electro-magnetic motors; (2) major charactoristics of the actuator is similar to
24、 human muscles 67. The prototype actuators for Skil Mate, shown in Figure 2, is 8mm (5/16 inch) diameter and 150mm (5.9 inch) long which generate more than 200N at 400kPa (58 psi). Force measurement of the actuator is shown in Figure 3. From the measurement. model of the actuator is shown as IV - 98
25、5 below. Here F P : Pressure in (kPa) E : Strain a : Constant (1.568 NkPa) b : Constant (0.7696 NkPa) C : Constant (86.0 N) : Output Force in (N) Figure 2. McKibben Artificial Muscle for Ski1 Mate 250 I I 200 4 150 v 0 e 9 100 50 0 50 150 250 350 450 Pressure (kPa) This joint has been PID controlled
26、 for basic data acquisition. Experimental result of PID control without load is shown in Figure 5. (1) Figure 3. Actuator Output Elbow Joint Prototype elbow joint is composed of two artificial muscle actuators and an incremental encoder (shown in Figure 4). The actuators are placed as tendons for th
27、e elbow joint and generate joint torque. Electro-pneumatic regulators and a PC computer control the actuators. The weight of this joint is 3768. Tactile sensors (pressure sensitive conducting rubber) are going to be attached to detect human movement. Figure 4. Elbow Joint with artificial muscles _ E
28、lbow Joint Contml 100 00 1 3 f 40 20 0 0 5 10 15 20 25 30 35 Tima (sec) Figure 5. Elbow position control example The elbow joint with pneumatic cylinders (shown in Figure 6) has been also built for comparison with the artificial muscle actuators. I V - 986 Figure 6. Elbow joint with pneumatic cylind
29、ers Wrist Joints The wrist joints have also been designed and built. The wrist joints have 2-DOF that are the roll and the pitch. Components of the joint are almost same as the elbow joint. The wrist joints have already assembled with the elbow joint then the joints plan to be tested and improved. T
30、he assembled joints are shown in Figure 7. Figure 7. Assembled joints Fingers The finger joints are shown in Figure 8 and Figure 9. The finger joints are composed of the thumb, the pointing finger, and the middle finger. The pointing finger and the middle finger has 2-DOF each, that are the MCP and
31、PIP (proximal interphalangeal) joints. The thumb has 3-DOF, which are the CMC (carpometacarpal), the MCP, and the IP (interphalangeal) joints. The small pneumatic cylinders drive each joint. The pneumatic cylinders generate the flexion forces of the fingers and the extension forces are generated by
32、the IV-987 passive coil springs. The artificial muscle actuators are going to be attached to the glove for extension force if the spring forces are not sufficient. Pressure sensitive conductive rubbers are attached to the fingertips to measure the force between the fingers and the gloves. Induction
33、position sensors are to be attached to measure the finger joint angles. Figure 8. Prototype glove Figure 9. Finger joints without glove Future Works Next step of the prototype development is to assemble the fingers, the wrist joints, and the elbow joint. And, haptic devices are planned to attach the
34、 fingers. Goal of the project Goal of the Ski1 Mate project is to develop a prototype exoskeletal machine for a spacesuit. The prototype model will consist of an upper torso assembly, and a pair of arms with gloves. This prototype model will be placed between pressure garment and insulation layer. T
35、he arms of the prototype have shoulder joints, an elbow joint, and wrist joints. Each joint is driven by pneumatic actuators and can sense joint angles. Tactile sensors are to be attached to detect human motion, so that the machine can follow the astronauts movement. Because the prototype model is a
36、lways interfaced to human, impedance control will be appropriate for man-machine cooperation. A Force-Torque sensor will be need between the wrist and the glove to accomplish the impedance control. The structure of the glove itself and the interface between astronauts hand and the glove will be stud
37、ied and carefully designed. Haptic devices such as tactile or slipping-off sensors and displays will be need to accomplish skilful tasks. 5. APPLICATION FOR CONSTRUCTION WORK Nowadays, “industrialized” andlor “advanced” construction systems are more popular in Japan and in the world. These systems r
38、ealized effective production in shorter term and less labor power that caused better business profit to construction industries. On the systems, major work is done by construction machines supervised by a high performance information networks with a lot of computers. Automatic systems and robots are
39、 participating to the construction sites. Reducing the labor cost on the construction sites make more business profit. On such construction sites, human workers are going to be one of the construction system components as a machine operator, or an intelligent transportation device, or a flexible han
40、dling machine. Modern and advanced construction systems, such as automated and robotic construction systems, are transplanted high-level skill from human workers. While a lot of automated systems have been developed and practically used for construction work, human participation to the construction
41、work is inevitable. The reasons are as below: (1) There are hundreds of tasks in one construction site so that it is not realistic to apply automated systems to every task. (2) Each construction site has different condition, which comes from design of the structure, environment of the site, etc.; as
42、 a result, one particular automated system is not always applicable to the other construction sites. (3)Some of the humans skill has not been realized by automated systems. Of course, there exist tasks that can not be done without automated systems. human skills are need. 6. CONCLUSION A concept of Ski1 Mate and its application for EVA are introduced. And, development status of the prototype model for a space suit is outlined. The first goal of the prototype development is to assemble
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 公寓管理部竞选
- 2024年硬质合金喷焊粉项目资金需求报告
- 2022年信阳市事业单位联考招聘考试试卷及答案解析
- 尝试与猜测:鸡兔同笼 (教案)2023-2024学年数学五年级上册
- 抖音App添加听歌功能需求文档
- 广东省阳江市高中名校2024届高三适应性调研考试数学试题含解析
- 面试套路三步曲:如何用产品思维搞定面试
- 广东省揭阳一中、潮州金中2024届高考数学押题试卷含解析
- 九年级数学上册-期中测试-(新版)湘教版
- 小米汽车系列二:首款纯电轿车上市并开启交付打造人车家全生态
- 2022年探索与发现走进科技馆教案
- 吉斯本GOMC有机儿童成长奶粉联合运动干预疗法对青春期前7-12岁儿童身高发育的影响
- 绳结的各种打法PPT课件
- 神经介入产品介绍
- 思维五取蕴苦
- Jolly Phonics自然拼读全套(教材+指导手册+ 自然拼读教程)pdf
- 《斗首择日法》
- 农化服务课件ppt
- DEK系统安装及校正265HORIZON
- 二手房交易协议书
- 故事梦工厂-“自定义动画”的使用-说课稿.ppt
评论
0/150
提交评论