版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、ICEM CFD/AI*Environment V11,Hexa Meshing,9/9/05,Inventory #002277 D1-2,What is a Blocking?,A hexa mesh is created by first making a “blocking” A blocking breaks down a geometry into large brick-shapes and structures the direction of grid lines by the arrangement of the blocks Each “block” is easily
2、meshed with a pure Cartesian mesh Some blocks can be defined as “swept” and be unstructured along one face Block entities (faces and edges) are projected onto the geometry The blocking is saved to an independent file, and can be loaded onto a different geometry,Geomtery,Blocking,Mesh without project
3、ion,Mesh with projection,9/9/05,Inventory #002277 D1-3,Block structure is created independent of geometry “Top down” topology creation The user as sculptor instead of brick layer One-step creation of advanced topologies (O-grid) “Bottom up” topology creation Blocking is built up like “laying bricks”
4、 Create blocks Extrude face Copy topologies Combinations of top-down and bottom-up methods can be used,Blocking Approach Top Down and/or Bottom Up,9/9/05,Inventory #002277 D1-4,Use same geometry (tetin) as used with Tetra Does not necessarily need to be a completely enclosed volume Points, material
5、points (bodies), and curves are not required but are very useful Use Build Topology to quickly build all curves and points Block structure is projected to geometry Surfaces automatically Curves and points manually projected,Geometry Requirements for Hexa,Associating Face to Surface to a dummy point
6、family or Interpolation can effectively mesh where geometry doesnt exist,Geometry,Blocking,9/9/05,Inventory #002277 D1-5,Geometry/Blocking Nomenclature,Geometry Point Curve Surface Volume (material point, body),Blocking Vertex Edge Face Block,Point,Curve,Material point/body,Surfaces,Block,Vertex,Edg
7、e,Face,Note: “curve” refers to lines, arcs, and splines,9/9/05,Inventory #002277 D1-6,Structure blocking to capture the shape of the geometry Top down split and discard unused blocks Bottom up create block by extrusion, creating, copying Associate blocking to geometry Usually just edges to curves Mo
8、ve vertices onto geometry Manual and automatic methods Assign mesh sizes Quickly by setting sizes on surfaces and/or curves Fine tune by setting edge distributions View mesh and check/improve quality Write out mesh,Blocking Process Overall Process,9/9/05,Inventory #002277 D1-7,Blocking Process - Ini
9、tialize Blocking 3D or 2D Planar,New Blocking 3D One 3D volume block encompassing selected entities 2D Planar One 2D block on constant XY plane around entire 2D geometry No surfaces required 2D Surface Blocking Discussed next slide,9/9/05,Inventory #002277 D1-8,Initialize Blocking 2D Surface Blockin
10、g,Automatic surface blocking Each surface becomes one 2D block Free blocks fully unstructured Most robust Mapped structured Aligned mesh along 4 block boundaries edges,Unstructured block,Must Build Topology first Can always convert blocks between free and mapped afterward: Edit Block - Convert Block
11、 Type,9/9/05,Inventory #002277 D1-9,Blocking Process Structuring Blocking to Fit Geometry,Top down approach,Start with one block which encloses the entire geometry,Split the block to capture the underlying shape,Delete unused blocks,Note: Deleted blocks are put into the part VORFN by default, so the
12、y can be re-used later if wanted,9/9/05,Inventory #002277 D1-10,Blocking Process Associate Blocking to Geometry,Associate blocking to geometry Usually just Edges to Curves In the final mesh, edges will take the shape (be projected to) these curves Right click on Edges - Show association in the model
13、 tree to display the association arrows,9/9/05,Inventory #002277 D1-11,Blocking Process Move Vertices onto Geometry,Move vertices to better represent the shape All visible vertices can be projected to the geometry at once Can be moved individually along the geometry Single or multiple at a time Alon
14、g fixed plane or line/vector,9/9/05,Inventory #002277 D1-12,Moving Vertices of Different Associations,Color Indicates type of association and how a vertex will move (edges also follow these colors, except red) Red Constrained to a point Cant be moved unless association is changed Green Constrained t
15、o a curve Vertex slides along that particular curve White (black on light background) Constrained to surfaces Vertex will slide along any ACTIVE surface (surface parts which are turned on in the model tree) If not on a surface, it will jump to the NEAREST ACTIVE surface when moved Blue Free (usually
16、 internal) vertex Select near the vertex on the edge to move along edge direction,9/9/05,Inventory #002277 D1-13,Blocking Process Assign Mesh Sizes,Assign mesh sizes Hexa sizes can be assigned on surfaces and curves for a quick mesh Or set edge-by-edge for fine tuning Automatic Copy to parallel edge
17、s,9/9/05,Inventory #002277 D1-14,Viewing the Projected Shape of Edges,Right click on Edges - Projected shape to view the shape of the edges when the mesh is computed Mesh sizes must first be set, and the mesh computed, because it actually just moves every node on every edge to its final position in
18、the mesh,9/9/05,Inventory #002277 D1-15,Blocking Process View Mesh,Pre-Mesh Create mesh at any stage of the process Mesh with different projection methods Use Project faces to fully represent the geometry View only certain surface mesh by turning on only that Part in the model tree Use Scan planes t
19、o view internal mesh (covered later),No projection,Face projection,9/9/05,Inventory #002277 D1-16,Blocking Process Checking Quality,Using the Quality Histogram Determinant Measurement of element deformation Most solvers accept 0.1 Shoot for 0.2 Angle Element minimum internal angles Shoot for 18 degr
20、ees Aspect ratio Volume Warpage Shoot for 45 degrees Many more metrics,You can display elements in a given range by selecting the histogram bar,9/9/05,Inventory #002277 D1-17,Blocking Process Writing Out Mesh,Convert pre-mesh to a permanent mesh Two formats depending on what your solver takes Unstru
21、ctured: One mesh file. Nodes are described only by location. Structured: Multiblock format with I,J,K indices for vertices. Blocking changes will no longer affect this mesh The mesh can now be edited with any of the tools from the Edit mesh tab The mesh can now be smoothed,9/9/05,Inventory #002277 D
22、1-18,3D Pipe Junction Tutorial,Try the 3D Pipe Junction Workshop #2,9/9/05,Inventory #002277 D1-19,O-Grids - Definition,An O-grid is a series of blocks created in one step which arranges grid lines into an “O” shape or a wrapping nature 3 basic types created through the same operation all referred t
23、o as “O-grids” O-grid C-grid (half O-grid) L-grid (quarter O-grid) Reduce skew where a block corner must lie on a continuous curve/surface Cylinders Complex geometries Improves efficiency of node clustering near walls for CFD applications,O-grid,C-grid,L-grid,No O-grid,O-grid,9/9/05,Inventory #00227
24、7 D1-20,Creating O-Grids Default O-Grid,Select blocks for O-grid Can select by visible, all, part, around face, around edge, around vertex, 2 corner method, or individual selection,Note: internal block has all internal (blue) edges and vertices,7 blocks in 3D,5 blocks in 2D,Select specific blocks or
25、 around face, edge, or vertex,9/9/05,Inventory #002277 D1-21,Creating O-Grids Adding Faces (Edges in 2D),O-grid passes through this face,Adding faces during O-grid creation O-grid “passes through” the selected block faces In general, add faces on the “flat parts” Adding a face actually adds blocks o
26、n both sides of the face,Examples of uses Pipe ends Symmetry planes Complex geometries,O-grid passes through this face,Half O-grid (C-grid),9/9/05,Inventory #002277 D1-22,Creating O-Grids Adding Multiple Faces,Any number of faces can be added around a selected block If all the faces are added around
27、 a block, the result is no change since the O-grid passes through all the faces,Quarter O-grid (L-grid),Seen as a C-grid in one direction and an L-grid in another direction,Quarter O-grids can be used to block triangular shapes,9/9/05,Inventory #002277 D1-23,Creating O-Grids Around Blocks,Select Aro
28、und block(s) to create the O-grid around the selected blocks Useful for creating wrap-around grid around a solid object Examples Opposite order of creation from block around/O-grid inside Flow over a cylinder Boundary layer resolution around an airplane or car body,9/9/05,Inventory #002277 D1-24,Sca
29、ling O-Grids,O-grids can be re-sized after or during creation By default the O-grid size is set to minimize block distortion You are actually scaling all parallel O-grid (radial) edges to the selected edge The selected edge is given a factor of 1 Numbers 1 will shrink the edge and thus create a larg
30、er inner block,Selected edge factor=1,Factor=0.3,9/9/05,Inventory #002277 D1-25,O-Grids Example Usage,This mesh can be improved by using an O-grid An example of bad mesh in the block corners,Before O-grid,Right mouse click on the histogram to access options like show, replot, or done,9/9/05,Inventor
31、y #002277 D1-26,Index Scheme,All blocks and vertices are defined with a global index scheme Initial block has i,j,k indices aligned with Cartesian x,y,z, global coordinates Subsequent blocks created by the split operation will maintain that orientation O-grids will not conform to this orientation, s
32、o each O-grid creates a new index direction (O3, O4, etc) (i,j,k correspond to dimension 0,1,2) Vertex Indices can be displayed by right clicking on Vertices - Indices in the model tree,9/9/05,Inventory #002277 D1-27,Using Index Control,Blocks can be turned off and on based on indices Use the index
33、control to turn blocks off and on Many operations can be applied to only the visible blocks Split blocks Extend split Rescale O-grid,Resets everything to fully visible,Select corners is often faster than toggling the index arrows,9/9/05,Inventory #002277 D1-28,VORFN,A region of blocks called VORFN s
34、urrounds the blocking The reserved part name VORFN is created in the model tree when blocking is initialized It is used to maintain the global index scheme, and as a “recycling” part Indices begin at 0 because this is the VORFN region Deleting blocks normally just changes the part to VORFN Blocks ca
35、n be moved back out of VORFN to another part Deleting blocks permanently gets rid of the block and rebuilds VORFN as an O-grid,Turn on to see VORFN,Selected blocks are actually removed and VORFN is rebuilt,9/9/05,Inventory #002277 D1-29,3D Pipe Junction Tutorial,Finish 3D Pipe Workshop, Capture the
36、Rod and Add O-Block,9/9/05,Inventory #002277 D1-30,Scan Plane,Scan planes to view internal mesh Use as secondary to quality histogram to diagnosis causes of bad elements Use Select button to select the index whose plane is normal to the selected edge Or select the number of the index direction #0 i
37、#1 j #2 k #3, 4, etc O-grids,Right click on Pre-mesh - Scan planes to bring up the scan plane menu,Select to select an edge The scan plane will be normal to this edge,9/9/05,Inventory #002277 D1-31,3D Pipe Junction Tutorial,Examine the 3D Pipe Mesh Using scan planes and Index Control,9/9/05,Inventor
38、y #002277 D1-32,Extend Split,Think of a split as a plane (even though it does not have to be planar) Select an edge at the outside of this “plane” and it will extend in all directions Split only goes through the displayed blocks Use the index control to limit the displayed blocks,Select edge,Select
39、edge,Select Project vertices to have it automatically project new visible vertices to the nearest place on their associated geometric entities,9/9/05,Inventory #002277 D1-33,Edges are by default linear before projection Edges can be shaped using split edge Spline Linear Control point Use Move vertex
40、 to move splits after splitting Split edge will also override the automatic interpolation of edges during mesh computation,Shaping Edges Split Edge,Spline,Linear,Control point,Original edge,Multiple splits,9/9/05,Inventory #002277 D1-34,Shaping Edges Split Edge Example,Using split edge to shape bloc
41、k faces to make a hole where it doesnt exist in the geometry,Geometry (gear),9/9/05,Inventory #002277 D1-35,Shaping Edges Link Edge,Use one edge to control the shape of another Select source edge then target edge(s) Enter factor (higher number = greater curvature),Source edge,Target edge,Factor = 0.
42、9,Factor = 1.3,Factor = 0.5,9/9/05,Inventory #002277 D1-36,Bottom-Up Meshing Methods,Top-down is, generally, more robust Bottom-up methods improve flexibility Transform Blocks Translate Rotate Mirror Scale 2D to 3D extrusion Translate Rotate Block independently and merge Extrude face Create block,9/
43、9/05,Inventory #002277 D1-37,Transforming Blocks,Simply transform selected blocks or make a copy and merge the transformed copy with the previous blocking Select blocks to transform Select method Translate Rotate Mirror Scale Enter parameters necessary for method,Mirror example,9/9/05,Inventory #002
44、277 D1-38,Create block types Hexa 8 vertices or locations (selection order is important) 2 faces Quarter O-grid (Y-grid) Degenerate,Create Block Hexa (Vertex Locations),1,4,3,2,5,6,7,8,Select 8 vertices,Select 2 faces,9/9/05,Inventory #002277 D1-39,8,7,6,5,4,1,3,Create Block Hexa (Geometry Locations
45、),What if I dont have 8 vertices to select? Select the vertices that you do have Press middle mouse button Select the rest of the locations on the screen The same order must be maintained as before,2,Press middle button,9/9/05,Inventory #002277 D1-40,Extrude Face,Select block face (select face or us
46、e two corner method) Interactive Drag with the pointer Extrude a Fixed distance Enter distance Extrude along curve Select curve,Extrude along curve,9/9/05,Inventory #002277 D1-41,Merge Vertices,One by one Multiple within tolerance When merging individually, select two vertices at a time With Merge t
47、o average off, the second vertex will merge to the first With Merge to average on, both vertices merge to the middle of the two Use to join separate topologies together Use to make degenerate blocks,1,2,1,2,9/9/05,Inventory #002277 D1-42,Deleting Splits and O-Grids,Splits and O-grids can be deleted
48、by using Merge vertices - propagate Select two vertices at the ends of an edge running in the direction you want to delete Middle click, then Confirm The second vertex merges to the first vertex when Merge to average is off, and the merge will be propagated If deleting an O-grid, only select the ver
49、tices of one radial edge,1,2,1,2,Deleting a split,Deleting an O-grid,9/9/05,Inventory #002277 D1-43,Delete Blocks Permanently,Equal number of nodes across hole,Number of nodes can be unequal,Delete blocks will, by default, move blocks to the part VORFN, which is more stable than permanently deleting
50、 blocks (doesnt recompute indices) However, there are some situations where deleting permanently is useful Deleting all of VORFN can serve as a repair tool in complex topologies (indices get reconfigured) Deleting individual blocks will free up node connectivity across VORFN blocks,Delete block perm
51、anently,9/9/05,Inventory #002277 D1-44,Crankshaft Tutorial,Try the Crankshaft Workshop #2,9/9/05,Inventory #002277 D1-45,Advanced and CFD Oriented Features,9/9/05,Inventory #002277 D1-46,Three Basic uses of O-Grids,Three basic uses of O-grids Capture the shape of the geometry Usually done early in t
52、he blocking process Improve element quality in block corners where surfaces do not make a corner Improve efficiency of node clustering near walls Boundary layer resolution These last two are usually accomplished with the same O-grid, and done late in the blocking process,Example of using an O-grid t
53、o capture the basic shape as the first step in the process,Quarter O-grid,9/9/05,Inventory #002277 D1-47,Sphere Cube - Ogrid,An Ogrid works well with this geometry (half-O-grid),9/9/05,Inventory #002277 D1-48,Set Location,Set X, Y, and/or Z of selected vertices Select Ref. Vertex, then select vertic
54、es to move or use the index control and select all visible vertices (“v”) Select directions to move (Modify X, Y, Z) Can use a local coordinate system (cylindrical, Cartesian) If cylindrical coor. System, (x, y, z) becomes (r, , z) Enter values or use the values from the Ref. vertex or screen locati
55、on Method can be Set Position or Increment Apply,z,Set z coordinate of vertices,Select these vertices,9/9/05,Inventory #002277 D1-49,Align multiple vertices in one plane with vertices in another plane (or split dimension) Select Along edge direction, then select the edge that connects the two planes
56、, or runs approximately normal to the split plane that you want to move inside Select Reference vertex, then select any vertex in the plane you want to align to. These vertices will remain fixed Select the plane to allow vertex movement within (XY, YZ, XZ, or User Defined). The User Defined plane mu
57、st be specified with a normal vector, such as (1 1 0) Apply,Align Vertices,Move vertices in this plane,Select this edge,Select any of these vertices as reference,All visible vertices not sharing the reference index will be moved,9/9/05,Inventory #002277 D1-50,Create Blocks 2D to 3D,A 2D blocking can
58、 be extruded into a 3D blocking by three different methods Fill Auto creation of 3D blocking from enclosed 2D surface blocks Translate Rotate,Extrudes points into curves and curves into surfaces where 3D geometry doesnt exist,Number of nodes in circumferential direction,Rotate,Surface mesh and scan
59、planes,9/9/05,Inventory #002277 D1-51,1,6,3,2,5,4,Create Block Wedge,Degenerate Select 6 vertices or locations Order is important Grid lines converge at vertices 1 and 4 Results in penta6 (prism) elements along one edge Quarter-O-Grid Results in all Hexa “wedge” (Y configuration),Degenerate,Quarter-O-Grid,9/9/05,Inventory #002277 D1-52,5,4,3,1,2,6,Swep
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 汽车加氢站简介演示1
- 诺和灵30R治疗糖尿病23例疗效观察
- 云南省峨山彝族自治县高中生物-第四章-基因的表达-4.1《基因指导蛋白质的合成》课件2-新人教版必修
- 《理工英语1》国家开放大学一平台机考满分题库2027珍藏版
- 炎症性肠病病人的护理
- 细胞质基质与内膜系统
- 老年人常见病多发病预防
- 老年痴呆症药物治疗新策略讲座
- 2027年春季开学考试高二英语复习卷及答案
- 2027年天津市高考二模数学模拟卷及答案
- 2025年(完整版)三级安全教育真题及答案(2025年)
- 中国鼻炎诊疗指南(2026版)
- 2026年数据文员笔模拟题目及答案详解
- T/COSHA 48-2024医疗机构安全生产资料管理规范
- GB 48145-2026井工煤矿机电设备完好性要求
- GB/T 18590-2025金属和合金的腐蚀点蚀评价指南
- 云南节庆活动管理办法
- 大学函数极限题目及答案
- JG/T 271-2019粘钢加固用建筑结构胶
- 医院挂账结算协议书
- 入团考试时事试题及答案解析
评论
0/150
提交评论