软包锂电制造完整工艺流程.ppt

1、2020/8/17,1,软包锂电制造流程 一、各控制工序流程图,cw,2020/8/17,2,配料,烤箱,作用:除湿、除潮,2020/8/17,3,搅拌机,2020/8/17,4,高速搅拌机,2020/8/17,5,搅拌机,2020/8/17,6,1、浆料粘度,粘度计,2020/8/17,7, 涂布,浆料过篩;作用:将杂质、大颗粒筛出,上面放120目塞网,2020/8/17,8,涂布机,2020/8/17,9,作用:放铜箔、铝箔 及单面极片,2020/8/17,10,半自动上料机,2020/8/17,11,2020/8/17,12,刀槽,2020/8/17,13,涂布刀,千分表(作用:极片厚度

2、参考数据),作用:料槽,高度需保持不变;,2020/8/17,14,2020/8/17,15,2020/8/17,16,纠偏器,作用:控制收卷整齐度,2020/8/17,17,自动上料缸,作用:保持液面高度稳定; 浆料保持搅拌状态;,2020/8/17,18,段切机,分切机,极片段切,段切机,2020/8/17,19,2020/8/17,20,极片烘烤,烤箱,2020/8/17,21,辊压,辊压机,2020/8/17,22,冲切,2020/8/17,23,2020/8/17,24,极片分档,2020/8/17,25,电子称,档次栏,2020/8/17,26,极耳断切机,2020/8/17,27

3、,2020/8/17,28,隔膜分切机,2020/8/17,29,隔膜断切机,隔膜除静电机,2020/8/17,30,叠片,2020/8/17,31,叠片夹具,2020/8/17,32,正负极点焊(超声波金属焊接机),2020/8/17,33,正极点焊,负极点焊,2020/8/17,34,2020/8/17,35,2020/8/17,36,2020/8/17,37,极耳修剪,2020/8/17,38,2020/8/17,39,预封,2020/8/17,40,包装,包装机,2020/8/17,41,热封模具,2020/8/17,42,自动胶纸切割机,2020/8/17,43,检测内阻,2020/

4、8/17,44,2020/8/17,45,极片平压机,2020/8/17,46,卷绕,隔膜架,放极片盒,卷针,2020/8/17,47,电芯平压机,2020/8/17,48,极耳冲切机,2020/8/17,49,冲压成形,成形机,2020/8/17,50,2020/8/17,51,切料处,2020/8/17,52,成形机,2020/8/17,53,切料处,2020/8/17,54,冲头,2020/8/17,55,送料处,2020/8/17,56,框式液压包装盒成形机,2020/8/17,57,冷却箱,2020/8/17,58,成型模具,2020/8/17,59,裁纸刀,2020/8/17,60,2020/8/17,61,垫板台、模块、弹簧刀,2020/8/17,62,注液,电解液搅拌机,2020/8/17,63,2020/8/17,64,2020/8/17,65,2020/8/17,66,预充,检测设备,全程监视器,2020/8/17,67,自动抽气机,2020/8/17,68,抽气平压机,将电芯的气体抽出.,2020/8/17,69,热封机,2020/8/17,70,切边机,2020/8/17,71,烫边机,2020/8/17,72,折边机,2020/8/17,73,打码机,作用:对电芯标识以便追述.,2020/8/17,74,上夹板,作用