VSS硬件软件要求及配置

1、一VSS硬件软件要求如下(摘自CISCO文档)Hardware and Software Requirements and RestrictionsHardware/SoftwareRequirementsMinimum SoftwareCisco IOS Software Release 12.2(33)SXH1Feature Set Requirement: IP Base* or betterSupervisor EngineVirtual Switching Supervisor 720-10GE (VS-S720-10GE-3C and VS-S720-10GE-3CXL)Note:

2、 Initial release supports a single supervisor engine per virtual switch member (orchassis). This restriction will be removed in a future software release.Modules All 6700 series modules with Centralized Forwarding card (CFC) All 6700 series modules with Distributed Forwarding Card (DFC) 3C or DFC3CX

3、LNote: Support for WS-X6716-10G line card is available on 12.2(33)SXH2 and later version of software releases.Distributed Forwarding Card (DFC)DFC3C (WS-F6700-DFC3C and WS-F6700-DFC3C-XL)VSL Ports: 10 Gigabit Ethernet Ports Virtual Switching Supervisor 720-10GE WS-X6708-10G-3C and WS-X6708-10G-3CXL

4、WS-X6716-10G-3C and WS-X6708-10G-3CXL*Maximum VSL DistanceMaximum VSL distance depends on X2 optics used for VSL 10 Gigabit Ethernet connections: X2-10GB-CX4: 15m X2-10GB-LX4: 300m X2-10GB-SR: 26m (FDDI grade MMF), 300M with OM3 MMF) X2-10GB-LR: 10km X2-10GB-ER: 40km X2-10GB-LRM: 220m over MMF X2-10

5、GB-ZR: 80km*ChassisAll Cisco Catalyst 6500 chassis*Power Supply Cisco Catalyst 6503-E and 6504-E Switches: all supported power supplies Cisco Catalyst 6506, 6506-E, 6509, 6509-E, 6509-NEB-A, 6509-V-E, and 6513 Switches: 2500W and aboveService ModulesNetwork Analysis Module 1 and 2Intrusion Detection

6、 Module*Wireless Integrated Services Module*Firewall Integrated Services Module*Application Control Engine Module*WAN ModulesNot currently supported*Cisco Catalyst 6509-NEB Switch and Cisco Catalyst 6503 Switch (non-E) not supported* Supported WITH 12.2(33)SXI* Supported WITH 12.2(33)SXI1二交换机硬件检查（1）

7、查看交换机主备引擎SSO状态，并确保主备引擎使用的相同版本IOS。MCB_CORE#sh redundancy Redundant System Information :- Available system uptime = 49 minutesSwitchovers system experienced = 2 Standby failures = 0 Last switchover reason = user forced Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode =

8、 sso Maintenance Mode = Disabled Communications = UpCurrent Processor Information :- Active Location = slot 5 Current Software state = ACTIVE Uptime in current state = 15 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE S

9、OFTWARE (fc4)Technical Support: /techsupportCopyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_team BOOT = sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin,12; Configuration register = 0x2102Peer Processor Information :- Standby Locati

10、on = slot 6 Current Software state = STANDBY HOT Uptime in current state = 10 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)Technical Support: /techsupportCopyright (c) 1986-2011 by Cis

11、co Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_team BOOT = sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin,12; Configuration register = 0x2102（2）查看IOS版本是否符合VSS软件需求MCB_CORE#sh verCisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEA

12、SE SOFTWARE (fc4)Technical Support: /techsupportCopyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_teamROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) MCB_CORE uptime is 49 minutesUptime for this control processor is 22 minut

13、esTime since MCB_CORE switched to active is 16 minutesSystem returned to ROM by Stateful Switchover at 09:51:40 UTC Thu Sep 29 2011 (SP by reload)System image file is sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.binLast reload reason: Reason unspecifiedThis product contains cryptographic f

14、eatures and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompli

15、ance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:

16、/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email .cisco WS-C6509-V-E (R7000) processor (revision 1.0) with K/65536K bytes of memory.Processor board ID FOX1520GBXRSR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cach

17、eLast reset from s/w reset1 Virtual Ethernet interface78 Gigabit Ethernet interfaces16 Ten Gigabit Ethernet interfaces1917K bytes of non-volatile configuration memory.8192K bytes of packet buffer memory.65536K bytes of Flash internal SIMM (Sector size 512K).Configuration register is 0x2102（3）查看交换机模块

18、状态MCB_CORE#sh moduleMod Ports Card Type Model Serial No.- - - - - 1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1529KCB3 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1528JS7K 3 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1529JY6W 4 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL1527J0B7

19、5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1527HVJ7 6 5 Supervisor Engine 720 10GE (Hot) VS-S720-10G SAL1527HVKSMod MAC addresses Hw Fw Sw Status- - - - - - 1 30e4.dbf0.2d90 to 30e4.dbf0.2d97 2.3 12.2(18r)S1 12.2(33)SXI6 Ok 2 30e4.db78.88e8 to 30e4.db78.88ff 5.0 12.2(18r)S1 12.2(33)SXI6

20、Ok 3 30e4.db78.abc4 to 30e4.db78.abc7 3.2 12.2(14r)S5 12.2(33)SXI6 Ok 4 e8b7.48ed.b720 to e8b7.48ed.b74f 2.4 12.2(18r)S1 12.2(33)SXI6 Ok 5 588d.098a.8b8c to 588d.098a.8b93 4.0 8.5(4) 12.2(33)SXI6 Ok 6 0025.453a.2c9c to 0025.453a.2ca3 4.0 8.5(4) 12.2(33)SXI6 OkMod Sub-Module Model Serial Hw Status -

21、- - - - - 1 Distributed Forwarding Card WS-F6700-DFC3C SAL1529K353 1.4 Ok 2 Centralized Forwarding Card WS-F6700-CFC SAL1516BQXV 4.1 Ok 3 Centralized Forwarding Card WS-F6700-CFC SAL1528JT5W 4.1 Ok 4 Centralized Forwarding Card WS-F6700-CFC SAL15056C4G 4.1 Ok 5 Policy Feature Card 3 VS-F6K-PFC3C SAL

22、1529JYYH 1.1 Ok 5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1528JLGV 5.1 Ok 6 Policy Feature Card 3 VS-F6K-PFC3C SAL1529JYXN 1.1 Ok 6 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1529K0UJ 5.1 OkMod Online Diag Status - - 1 Pass 2 Pass 3 Pass 4 Pass 5 Pass 6 Pass（4）交换机同样检查以上信息ADMIN_CORE#sh redundancy Redundant Syst

23、em Information :- Available system uptime = 27 minutesSwitchovers system experienced = 2 Standby failures = 0 Last switchover reason = user forced Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = sso Maintenance Mode = Disabled Communications = UpCurrent Processor

24、Information :- Active Location = slot 5 Current Software state = ACTIVE Uptime in current state = 15 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)Technical Support: /techsupportCopyrig

25、ht (c) 1986-2011 by Cisco Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_team BOOT = sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin,12; Configuration register = 0x2102Peer Processor Information :- Standby Location = slot 6 Current Software state = STANDBY HOT Uptime in current sta

26、te = 10 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)Technical Support: /techsupportCopyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_team BOOT = s

27、up-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin,12; Configuration register = 0x2102ADMIN_CORE#sh verCisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)Technical Support: /techsupportCopyright (c) 1986-201

28、1 by Cisco Systems, Inc.Compiled Mon 28-Mar-11 12:09 by prod_rel_teamROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) ADMIN_CORE uptime is 28 minutesUptime for this control processor is 20 minutesTime since ADMIN_CORE switched to active is 15 minutesSystem returned to ROM by State

29、ful Switchover at 10:03:35 UTC Thu Sep 29 2011 (SP by reload)System image file is sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.binLast reload reason: Reason unspecifiedThis product contains cryptographic features and is subject to UnitedStates and local country laws governing import, expor

30、t, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with

31、applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us

32、 by sending email .cisco WS-C6509-V-E (R7000) processor (revision 1.0) with K/65536K bytes of memory.Processor board ID FOX1520GT6ESR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 CacheLast reset from s/w reset1 Virtual Ethernet interface78 Gigabit Ethernet interfaces1

33、6 Ten Gigabit Ethernet interfaces1917K bytes of non-volatile configuration memory.8192K bytes of packet buffer memory.65536K bytes of Flash internal SIMM (Sector size 512K).Configuration register is 0x2102ADMIN_CORE#sh moduleMod Ports Card Type Model Serial No.- - - - - 1 8 CEF720 8 port 10GE with D

34、FC WS-X6708-10GE SAL1528JW67 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1528JFCJ 3 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1529JY55 4 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL1521E3H1 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1527HVKT 6 5 Supervisor Engine 720 10GE

35、(Hot) VS-S720-10G SAL1527HVHCMod MAC addresses Hw Fw Sw Status- - - - - - 1 c89c.1ddc.a5f0 to c89c.1ddc.a5f7 2.3 12.2(18r)S1 12.2(33)SXI6 Ok 2 30e4.db49.fac0 to 30e4.db49.fad7 5.0 12.2(18r)S1 12.2(33)SXI6 Ok 3 0007.7d03.bd88 to 0007.7d03.bd8b 3.2 12.2(14r)S5 12.2(33)SXI6 Ok 4 e8b7.4824.18bc to e8b7.

36、4824.18eb 2.4 12.2(18r)S1 12.2(33)SXI6 Ok 5 0025.453a.2ca4 to 0025.453a.2cab 4.0 8.5(4) 12.2(33)SXI6 Ok 6 68ef.bd83.5100 to 68ef.bd83.5107 4.0 8.5(4) 12.2(33)SXI6 OkMod Sub-Module Model Serial Hw Status - - - - - - 1 Distributed Forwarding Card WS-F6700-DFC3C SAL1529K347 1.4 Ok 2 Centralized Forward

37、ing Card WS-F6700-CFC SAL1526HD0X 4.1 Ok 3 Centralized Forwarding Card WS-F6700-CFC SAL1529K1F0 4.1 Ok 4 Centralized Forwarding Card WS-F6700-CFC SAL1527HW6S 4.1 Ok 5 Policy Feature Card 3 VS-F6K-PFC3C SAL1529JYX4 1.1 Ok 5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1529K11S 5.1 Ok 6 Policy Feature Card 3 V

38、S-F6K-PFC3C SAL1529JZ17 1.1 Ok 6 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1527HRGZ 5.1 OkMod Online Diag Status - - 1 Pass 2 Pass 3 Pass 4 Pass 5 Pass 6 Pass三配置VSS（1）交换机配置以太通道以便以后VSL使用MCB_CORE(config)#int rang ten5/4,ten6/4MCB_CORE(config-if-range)#channel-group 30 mo on MCB_CORE(config-if-range)#no shMC

39、B_CORE(config)#int port-channel 30MCB_CORE(config-if)#no shADMIN_CORE(config)#int rang ten5/4,ten6/4ADMIN_CORE(config-if-range)#channel-group 40 mo onADMIN_CORE(config-if-range)#no shADMIN_CORE(config)#int port-channel 40ADMIN_CORE(config-if)#no shMCB_CORE#sh etherchannel summary Flags: D - down P -

40、 bundled in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3 S - Layer2 U - in use N - not in use, no aggregation f - failed to allocate aggregator M - not in use, no aggregation due to minimum links not met m - not in use, port not aggregated due to minimum links no

41、t met u - unsuitable for bundling d - default port w - waiting to be aggregatedNumber of channel-groups in use: 1Number of aggregators: 1Group Port-channel Protocol Ports-+-+-+-30 Po30(RU) - Te5/4(P) Te6/4(P) ADMIN_CORE#sh etherch sumFlags: D - down P - bundled in port-channel I - stand-alone s - su

42、spended H - Hot-standby (LACP only) R - Layer3 S - Layer2 U - in use N - not in use, no aggregation f - failed to allocate aggregator M - not in use, no aggregation due to minimum links not met m - not in use, port not aggregated due to minimum links not met u - unsuitable for bundling d - default p

43、ort w - waiting to be aggregatedNumber of channel-groups in use: 1Number of aggregators: 1Group Port-channel Protocol Ports-+-+-+-40 Po40(RU) - Te5/4(P) Te6/4(P) （2）配置VSS域号码为200，配置MCB_CORE在VSS中的主机号为1并给这台设备设置设置为优先级200.注：优先级范围是1-255，默认是100。 越高越优先成为VSS中的主交换机。MCB_CORE(config)#switch virtual domain 200MC

44、B_CORE(config-vs-domain)#switch 1 pri 200 （3）配置前面的以太通道30为VSLMCB_CORE(config)#int port-channel 30MCB_CORE(config-if)#switch virtual link 1MCB_CORE(config-if)#no sh（4）确保两台需要配置VSS的交换机PFC模式相同（如果不相同VSS配置完后会处在RPR状态），并强制配置PFC模式为PFC3C（因为本次测试中所有的引擎都是同一个版本，且都不支持PFC3CXL）MCB_CORE#sh platform hardware pfc modePF

45、C operating mode : PFC3CMCB_CORE(config)#platform hardware vsl pfc mode pfc3cSystem EARL mode will be forced to PFC3C on next bootup（5）保存并检查此时交换机的状态。MCB_CORE#wrMCB_CORE#sh switch virt Switch Mode : Standalone Not in Virtual Switch mode due to: Domain ID is configured but SWITCH_NUMBER is not set. Th

46、is implies an incomplete or failed Virtual Switch conversion process.（6）转换交换机模式为VSS模式，当输入“yes”确认后交换机会自动重启MCB_CORE#switch convert mode virtual This command will convert all interface namesto naming convention interface-type switch-number/slot/port,save the running config to startup-config and reload

47、the switch.NOTE: Make sure to configure one or more dual-active detection methodsonce the conversion is complete and the switches have come up in VSS mode.Do you want to proceed? yes/no: yConverting interface namesBuilding configuration.*Sep 29 10:36:57.435: %PFINIT-SP-5-CONFIG_SYNC: Syncing the sta

48、rtup configuration to the standby Router. OKSaving converted configuration to bootflash: .Destination filename startup-config.converted_vs-? 6糎HiU羴29 10:37:09.587: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.*Sep 29 10:37:09.587: %OIR-SP-6-CONSOLE: Changing console o

49、wnership to switch processor*Sep 29 10:37:09.791: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.*Sep 29 10:37:12.595: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.* - SHUTDOWN NOW -*Sep 29 10:37:12.583: %SYS-SP-5-RELOAD: Reload requested by Delayed Reload. Relo