ic3_display_lcd_qd043003c0-40-7led产品规格书_W

1、QIAO DIAN XIAN SHI Co.,LTD.LCM Specification()Preliminary Specification ( ) Final SpecificationPRODUCT TYPE:TFTMODULE PRODUCT P/N:QD43003C0-40-7LCE VERSION:V1QDCustomerShenzhen Qiaodian xianshi Co.,LTD.2/F,North of building A,Anle Industrial park,43 TEL:86-755-29124272Area,Baoan,ShenZhen, ChinaFAX:8

2、6-755-27835340SHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 1INSPECTION RESULTTESTED BYAPPROVED BYDESIGNED BYCHECKED BYAPPROVED BYQIAO DIAN XIAN SHI Co.,LTD.SHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 2DateRev.Reason27-10-2010V1NEWISSUERevision His

3、toryQIAO DIAN XIAN SHI Co.,LTD.CONTENTSGENERAL DESCRIPTIONG GENERAL FEATURES ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS OPTICAL SPECIFICATIONS BLOCK DIAGRAMPIN DESCRIPTION OUTLINE DIMENSION REGISTER VALUETIMING CHARACTERISTICSRELIABILITY AND INSPECTION STANDARD INSPECTION CRITERIONPACKING DI

4、MENSION PRECAUTIONSSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 3QIAO DIAN XIAN SHI Co.,LTD.1. General DescriptionThe QD43003C0-40 V1 model is a Color TFT LCD supplied by QIAO DIAN XIAN SHI CO., LTD. This main Module has a 4.3 inch diagonally measured active display area wi

5、th 480(RGB)X272 resolution. Each pixel is divided into Red, Green and Blue sub-pixels and dots which are arranged in vertical stripes.LCD color is determined with 262,000 colors signal for each pixel.The QD43003C0-40 V1 has been designed to apply the interface method that enables low power, high spe

6、ed, and high contrast.The QD43003C0-40 V1 is intended to support applications where thin thickness, wide viewing angle and low power are critical factors and graphic displays are important.2. General Features3. Absolute Maximum RatingsThe following are maximum values which, if exceeded may cause ope

7、ration or damage to the unit.ITEMSymbolMin.Typ.Max.UnitRemarkPower for Circuit DrivingVDD-0.3-3.3VPower for Circuit LogicVCI-0.3-5.0VLC Operating Voltage *1)Vop3.3VLED Forward VoltageVf-16-Vper LEDLED Forward CurrentIr-16-mAper LEDLED LuminanceBP-4200-cd/m2Storage HumidityHST10-90%RHAt 255 Storage T

8、emperatureTST-30-80 Operating Ambient HumidityH OP10-90%RHOperating Ambient temperatureTOP-20-70 SHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 4ItemDisplay PanelRemarkDisplay ModeNormally White, Transmissive LCDViewing Direction6 OCLOCKInput SignalsRGBOutside Dimensions105.5

9、mm(W)*67.2mm(H)*2.95mm(T)Effective Area-Active Area95.04mm(W)53.856mm(H)Number of Pixels480RGB272PixelsPixel Pitch0.198mm(H)0.198mm(W)Pixel ArrangementRGB Vertical stripesDrive ICOTA5180AQIAO DIAN XIAN SHI Co.,LTD.Note:*1)Liquid Crystal driving voltage.Due to the characteristics of LC Material, this

10、 voltage vary with environmental temperature.*2)Temp.60, Absolute humidity shall be less than 90%RH at 60 *3)Temp.60, 90%RH MAX.4. Electrical SpecificationMain Window Display(Unless specified, the ambient temperature Ta=25)PropertiesSym.MinTyp.MaxUnitNotePower for Circuit DrivingVDD1.652.83.3VNotePo

11、wer for Circuit LogicVCI2.72.83.0VNoteBLU Driving LogicVbat-VLogic Input VoltageLow VoltageVIL0-0.2VDDVHigh VoltageVIH0.8VDD-VDDVLogic Output VoltageLow VoltageVOL0-0.1VDDVHigh VoltageVOH0.9VDD-VDDVPower ConsumptionWhitePwT.B.DT.B.DT.B.DmWBlackPbT.B.DT.B.DT.B.DmWVertical StripePvT.B.DT.B.DT.B.DmWNot

12、e:The recommended operating conditions refer to a range in which operation of this product is guaranteed. Should this range is exceeded, the operation cannot be guaranteed even if the values may be without the absolute maximum ratings.Accordingly, please make sure that the module is used within this

13、 range. And these current values are measured under the condition that all devices are stopped, each component is stable and logic signal is input.5. Optical SpecificationSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 5QIAO DIAN XIAN SHI Co.,LTD.SHENZHEN QIAODIAN XIANSHI Co.,

14、LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 6QIAO DIAN XIAN SHI Co.,LTD.6. Block DiagramSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 7QIAO DIAN XIAN SHI Co.,LTD.SHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 8480(RGB)272Display PanelGate(TFT LCDsignalTr

15、ansmissive)(272)Source signal (480*3)WR, CS, RS, RESET, RDKADriver & Controller(All-In-One)(OTA5180A)Data(RGB),Power(VDD)Control Signal( WR, CS, RS, RESET, RD)M P U&P O W E RI/FQIAO DIAN XIAN SHI Co.,LTD.7. Pin DescriptionSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 9Pin NO

16、.SymbolDescription1LEDKLED BACKLIGHT(CATHODE2LEDALED BACKLIGHT(ANODE3GNDGROUND4VCCPOWER SUPPLY(DIGITAL 3.0V5R0RED DATA6R1RED DATA7R2RED DATA8R3RED DATA9R4RED DATA10R5RED DATA11R6RED DATA12R7RED DATA13G0GREEN DATA14G1GREEN DATA15G2GREEN DATA16G3GREEN DATA17G4GREEN DATA18G5GREEN DATA19G6GREEN DATA20G7

17、GREEN DATA21B0BLUE DATA22B1BLUE DATA23B2BLUE DATA24B3BLUE DATA25B4BLUE DATA26B5BLUE DATA27B6BLUE DATA28B7BLUE DATA29GNDGROUND30CLKCLOCK SIGNAL31DISPDISPLAY ON/OFF32HSYNCHORIZONTAL SYNC INPUT IN RGB MODE33VSYNCVERTICAL SYNC INPUT IN RGB MODE34DENDATA ENABLE35NCNC36GNDGROUND37XR(NC)TOUCHPLANEPIN/NC38Y

18、D(NC)TOUCHPLANEPIN/NC39XL(NC)TOUCHPLANEPIN/NC40YU(NC)TOUCHPLANEPIN/NC*105.11(O.D)97.90(LCM V.A)3.7595.04(LCD A.A)4.89*2.950.1(52.70)SP430-15B *R G BTFT 4.3 480 X RGB X 272VIEWDIRECTION152 1 XL XR YU YD 单层区A140PI补强 *0.30*18.390.5*20.5025.37(-)(-)(+)(+)B/L CIRCUIT DIAGRAM背光电流 20MA 电压 22V 深圳市桥电显示有限公司 1

19、0.04.07QD430003C0-40A V1 TAM480(RGB)X272 DOTS QIAO DIAN XIAN SHI Co.,LTD.8. OutlineDimensionSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 10*44.520.556.70(LCM V.A)2.8053.86(LCD A.A)4.32(31.25)19.655.000.5QIAO DIAN XIAN SHI Co.,LTD.9. Timing Characteristics9.1. 80-System bus

20、interface operation9.2. Timing CharacteristicsNormalWrite Mode(HWM=0), IOVcc=1.65V3.6V,Vcc=2.5V3.6VSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 11ParameterSymbolUnitMin.Max.UnitBus cycle time writetCYCWns100-Bus cycle time readtCYCRns160-Write low-level pulse widthPWLWns35-

21、Read low-level pulse widthPWLRns45-Write high-level pulse widthPWHWns35-Read high-level pulse widthPWHRns90-Write/Read rise/fall timetWR,wRfns-25Setup time WritetASns0-Setup time ReadtASns10-Address hold timetAHns2-Write data setup timetDSWns25-Write data hold timetHns5-Read data delay timetDDRns-10

22、0QIAO DIAN XIAN SHI Co.,LTD.9. 3 Reset Operation(VCC=1.653.1 V)10. Reliability and Inspection StandardNote:1) The test samples should be applied to only one test item.2) Sample size for each test item is 510pcs.3) For Damp Proof Test, pure water(Resistance1M) should be used.4) In case of malfunction

23、 defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judged as a good part.5) EL evaluation should be excepted from reliability test with humidity and temperature: Some defects such as black spot/blemish can happen by natural chemical reaction with humi

24、dity and fluorescence EL has.6) After the reliability test, the test samples should be inspected after 2 hours at least.7) Functional test is OK. Missing segment, shorts, unclear segment, non display, displaySHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 12No.Test ItemTest Co

25、nditionsRemark1High TemperatureStorage70, 120HrNoteOperation60, 120HrNote2Low TemperatureStorage-30, 120HrNoteOperation-20, 120Hr3High Temperature and High Humidity60, 90%RH, 120HrNote4Temperature CycleStorage-10(1Hr)25(5min)60(1Hr) 32 CyclesNoteOperation-20(1Hr)25(5min)60(1Hr) 25 Cycles5Peeling Off

26、 (Storage)500gf/cmNote6FPC Bending Test6,000 times, 2/secNote7Vibration Test(Storage)50HZ, 30min,Amplitude: 2 cm, X/Y/Z directionsNote8Drop Test60cm/ 3Corner/ 8Face, 1CycleNoteRead data hold timetDHRns5-QIAO DIAN XIAN SHI Co.,LTD.abnormally, liquid crystal leak are not allowed.8) After testing, the

27、current Idd should be within initial value 20%.9) No low temperature bubbles ,end seal loose and fall, frame rainbow, ACF bubble growing are allowable in the appearance test.11. Inspection Criterion11.1. Sampling MethodUnless otherwise agreed upon in writing, the sampling inspection shall be applied

28、 to the Customers incoming inspection.1) Lot size: Quantity per shipment lot2) Sampling type: Normal inspection , single sampling3) Inspection level: 4) Sampling table: MIL-STD-105D5) Acceptable Quality Level(AQL): Major=0.65Minor=1.511.2. Inspection Method1) Ambient Condition:a. Temperature: Room t

29、emperature 255b. Illumination: Single fluorescent lamp non-directive(300 to 700 Lux)2) Viewing distanceThe distance between the LCD and the inspectors eyes shall be at least 30-50cm.3) Viewing AngleThe inspection shall be conducted within normal viewing angle range.12.3. Inspection Criteria12.3.1. M

30、ajor defectSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 13No.ItemInspection StandardClassification of defects1All functional defects1) No display2) Display abnormally3) Open or missing segment4) Short circuit5) Excess power consumptionMajorQIAO DIAN XIAN SHI Co.,LTD.12.3.2.

31、 Cosmetic DefectSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 14No.ItemInspection StandardClassification of defects1(spot defect) Black and White spot pinholeFor dark/white spot, size is definedas =(x+y)/2Minor2(line defect) Black and White line Polarizer scratchMinorWidth(m

32、m)Length(mm);Acceptable Qty0.03Ignore0.03W0.05L3.0; N20.05W0.1L2.0; N20.1WDefine as spot defectSize (mm)Acceptable Quantity0.1Ignore0.100.1520.150.210.206) Backlight no lighting, flickering and abnormal lighting2MissingMissing componentMajor3Outline dimensionOverall outline dimension beyond the draw

33、ing is not allowedMajorQIAO DIAN XIAN SHI Co.,LTD.12.3.3. Cosmetic DefectSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LEDVERSION:V1Page 15No.ItemInspection StandardClassification of defects1Glass defect1) Chip on the cornerRemark: S=contact pad length; T=the thickness of glassChips on the co

34、rner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. Acceptable Quantity N2.Minor2) Chip on the edge of glassMinorXYZXYZ3.0ST3Polarizer defectDent or bubble(between the polarizer and glass)MinorSize (mm)Acceptable Qty0.10Ignor0.100.2020.200.3010.300QIAO DIAN XIA

35、N SHI Co.,LTD.n PRECAUTIONS FOR USING LCD MODULESHanding Precautions(1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical shock by dropping

36、it or impact.(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.(3) Do not apply excessive force to the display surface or the adjoining areas since thi

37、s may cause the color tone to vary. Do not touch the display with bare hands. This will stain the display area and degraded insulation between terminals (some cosmetics are determined to the polarizer).(4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Han

38、dle this polarizer carefully. Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks on. Condensation on the surface and contact with terminals due to cold will dam

39、age, stain or dirty the polarizer. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air.(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavi

40、ly contaminated, moisten cloth with one of the following solvents- Isopropyl alcohol- Ethyl alcoholDo not scrub hard to avoid damaging the display surface.(6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following.- Water- Ketone- Aromatic solventsWi

41、pe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. Avoid contacting oil and fats.(7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes isSHENZHEN QIAODIAN XIANSHI Co.,LTD.P/N: QD43003C0-40-7LE

42、DVERSION:V1Page 16Ignore0.5TAcceptable Quantity: N23) CreakCreaks tend to break are not allowed.MinorQIAO DIAN XIAN SHI Co.,LTD.accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment.(8) Install the LCD Module by using the mounting holes. When mounting

43、the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable.(9) Do not attempt to disassemble or process the LCD module.(10) NC terminal should be open. Do not connect anything.(11) If the logic circuit pow

44、er is off, do not apply the input signals.(12) Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it.- Do not alter, modify or change the shape of the tab on the metal frame.- Do not m

45、ake extra holes on the printed circuit board, modify its shape or change the positions of components to be attached.- Do not damage or modify the pattern writing on the printed circuit board.- Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.- Except for soldering the interface, do not make any alterati