华为三台堆叠-环形

1、配置三台交换机堆叠示例（环形拓扑）图1配置环形堆叠组网图组网需求在一个新建的企业网络中，要求接入设备具有充足的端口数目，并且希望网络结构简单，易于配置和管理。如图1所示，SwitchA、SwitchB和SwitchC三台接入交换机组成环形堆叠系统。配置思路采用如下的思路配置：1. 提前规划好堆叠方案。2. 按照前期的规划，完成各台交换机的堆叠配置，包括堆叠成员ID、堆叠优先级、堆叠域编号、堆叠端口等。完成后保存配置并将交换机下电。3. 连接交换机之间的堆叠线缆，然后将交换机上电。4. 检查堆叠组建是否成功。说明：本示例以先配置软件再连接线缆的方式组建堆叠。如果是先连接线缆再配置软件方式，请参照

2、配置两台交换机堆叠示例（先连线后配置方式）的思路进行配置。操作步骤1. 提前规划堆叠方案。 规划SwitchA的堆叠成员ID为1，SwitchB的成员ID为2，SwitchC的成员ID为3。 规划SwitchA作为主交换机，其堆叠优先级最高，为150。SwitchB的堆叠优先级为120。SwitchC的堆叠优先级为90。 规划堆叠域编号（Domain ID）为10，不与网络中其他堆叠系统的域编号冲突。 规划堆叠连接拓扑为环形。成员设备间用于堆叠连接的端口如图2所示。图2堆叠端口连接示意图2. 配置堆叠属性。# 配置SwitchA的堆叠优先级为150，Domain ID为10。缺省情况下，设备的

3、堆叠成员ID为1。此处默认SwitchA的堆叠成员ID为1，无需配置。 system-viewHUAWEI sysname SwitchA*HUAWEI commitSwitchA stackSwitchA-stack stack member 1 priority 150*SwitchA-stack stack member 1 domain 10*SwitchA-stack quit*SwitchA commit# 配置SwitchB的堆叠成员ID为2，优先级为120，Domain ID为10。 system-viewHUAWEI sysname SwitchB*HUAWEI commit

4、SwitchB stackSwitchB-stack stack member 1 priority 120*SwitchB-stack stack member 1 domain 10*SwitchB-stack stack member 1 renumber 2 inherit-configWarning: The stack configuration of member ID 1 will be inherited to member ID 2 after the device resets. Continue? Y/N: y*SwitchB-stack quit*SwitchB co

5、mmit说明：因SwitchB尚未重启，当前堆叠成员ID还是1，所以此时仍使用member 1来进行堆叠配置。因为修改堆叠成员ID时指定了inherit-config参数，所以SwitchB重启后会继承member 1的堆叠配置；如果不指定inherit-config参数，那么SwitchB重启后不会继承member 1的堆叠配置，需要使用member 2重新进行堆叠配置。# 配置SwitchC的堆叠成员ID为3，优先级为90，Domain ID为10。 system-viewHUAWEI sysname SwitchC*HUAWEI commitSwitchC stackSwitchC-st

6、ack stack member 1 priority 90*SwitchC-stack stack member 1 domain 10*SwitchC-stack stack member 1 renumber 3 inherit-configWarning: The stack configuration of member ID 1 will be inherited to member ID 3 after the device resets. Continue? Y/N: y*SwitchC-stack quit*SwitchC commit3. 配置堆叠端口。# 将SwitchA

7、的业务口10GE1/0/110GE1/0/2加入堆叠端口1/1，10GE1/0/310GE1/0/4加入堆叠端口1/2。SwitchA interface stack-port 1/1*SwitchA-Stack-Port1/1 port member-group interface 10ge 1/0/1 to 1/0/2Warning: After the configuration is complete,1.The interface(s) (10GE1/0/1-1/0/4) will be converted to stack mode and be configured with t

8、he port crc-statistics trigger error-down command if the configuration does not exist. 2.The interface(s) may go Error-Down (crc-statistics) because there is no shutdown configuration on the interfaces.Continue? Y/N: y*SwitchA-Stack-Port1/1 quit*SwitchA interface stack-port 1/2*SwitchA-Stack-Port1/2

9、 port member-group interface 10ge 1/0/3 to 1/0/4*SwitchA-Stack-Port1/2 quit*SwitchA commitSwitchA quit被配置为堆叠物理成员端口后，端口下会自动配置port crc-statistics trigger error-down。# 将SwitchB的业务口10GE1/0/110GE1/0/2加入堆叠端口1/1，10GE1/0/310GE1/0/4加入堆叠端口1/2。SwitchB interface stack-port 1/1*SwitchB-Stack-Port1/1 port member-

10、group interface 10ge 1/0/1 to 1/0/2Warning: After the configuration is complete,1.The interface(s) (10GE1/0/1-1/0/4) will be converted to stack mode and be configured with the port crc-statistics trigger error-down command if the configuration does not exist. 2.The interface(s) may go Error-Down (cr

11、c-statistics) because there is no shutdown configuration on the interfaces.Continue? Y/N: y*SwitchB-Stack-Port1/1 quit*SwitchB interface stack-port 1/2*SwitchB-Stack-Port1/2 port member-group interface 10ge 1/0/3 to 1/0/4*SwitchB-Stack-Port1/2 quit*SwitchB commitSwitchB quit# 将SwitchC的业务口10GE1/0/110

12、GE1/0/2加入堆叠端口1/1，10GE1/0/310GE1/0/4加入堆叠端口1/2。SwitchC interface stack-port 1/1*SwitchC-Stack-Port1/1 port member-group interface 10ge 1/0/1 to 1/0/2Warning: After the configuration is complete,1.The interface(s) (10GE1/0/1-1/0/4) will be converted to stack mode and be configured with the port crc-sta

13、tistics trigger error-down command if the configuration does not exist. 2.The interface(s) may go Error-Down (crc-statistics) because there is no shutdown configuration on the interfaces.Continue? Y/N: y*SwitchC-Stack-Port1/1 quit*SwitchC interface stack-port 1/2*SwitchC-Stack-Port1/2 port member-gr

14、oup interface 10ge 1/0/3 to 1/0/4*SwitchC-Stack-Port1/2 quit*SwitchC commitSwitchC quit4. 检查堆叠配置信息。# 上述配置完成后，执行命令display stack configuration查看配置是否与规划的一致，如果不一致，需要修改配置。以查看SwitchA为例。 display stack configurationOper : OperationConf : Configuration* : Offline configurationIsolated Port : The port is in s

15、tack mode, but does not belong to any Stack-PortAttribute Configuration:- MemberID Domain Priority Switch Mode Uplink PortOper(Conf) Oper(Conf) Oper(Conf) Oper(Conf) Oper(Conf)-1(1) -(10) 100(150) Auto(Auto) 4*40GE(4*40GE)-Stack-Port Configuration:-Stack-Port Member Ports-Stack-Port1/1 10GE1/0/1 10G

16、E1/0/2Stack-Port1/2 10GE1/0/3 10GE1/0/4-5. 保存配置后将设备下电。# 保存SwitchA、SwitchB和SwitchC的配置，然后将设备下电。SwitchB和SwitchC的配置与SwitchA相同，略。 saveWarning: The current configuration will be written to the device. Continue? Y/N: y6. 按照前期规划及配置，连接堆叠线缆。线缆连接完成后将设备上电。建议先将高优先级设备上电，以使其先完成启动，优先竞争为主交换机。7. 验证配置结果# 通过Console口或管理

17、网口登录堆叠系统，使用命令display stack查看堆叠是否组建成功。当通过管理网口登录时，需要使用主交换机的IP地址。 display stack-MemberID Role MAC Priority DeviceType Description-+1 Master 0004-9f31-d520 150 CE6850-48T4Q-EI 2 Standby 0004-9f62-1f40 120 CE6850-48T4Q-EI 3 Slave 0004-9f69-a391 90 CE6850-48T4Q-EI -+ indicates the device where the activat

18、ed management interface resides.如上所示，显示三台交换机的信息，表示堆叠建立成功，且主交换机为成员ID为1的设备，即SwitchA。# 查看堆叠系统拓扑信息。 display stack topologyStack Topology:- Stack-Port 1 Stack-Port 2 MemberID Status Neighbor Status Neighbor -1 up 2 up 3 2 up 1 up 3 3 up 2 up 1 -Stack Link:-Stack-Port Port Status PeerPort PeerStatus-Stack

19、-Port1/1 10GE1/0/1 up 10GE2/0/1 upStack-Port1/1 10GE1/0/2 up 10GE2/0/2 upStack-Port1/2 10GE1/0/3 up 10GE3/0/3 upStack-Port1/2 10GE1/0/4 up 10GE3/0/4 upStack-Port2/1 10GE2/0/1 up 10GE1/0/1 upStack-Port2/1 10GE2/0/2 up 10GE1/0/2 upStack-Port2/2 10GE2/0/3 up 10GE3/0/1 upStack-Port2/2 10GE2/0/4 up 10GE3

20、/0/2 upStack-Port3/1 10GE3/0/1 up 10GE2/0/3 upStack-Port3/1 10GE3/0/2 up 10GE2/0/4 upStack-Port3/2 10GE3/0/3 up 10GE1/0/3 upStack-Port3/2 10GE3/0/4 up 10GE1/0/4 up-8. 保存堆叠系统配置。说明：在检查堆叠已成功建立后，建议用户立即使用save命令保存堆叠系统配置。 saveWarning: The current configuration will be written to the device. Continue? Y/N:

21、y配置文件 堆叠系统的配置文件 # sysname SwitchA # stack # stack member 1 domain 10 stack member 1 priority 150 # stack member 2 domain 10 stack member 2 priority 120 # stack member 3 domain 10 stack member 3 priority 90 # interface Stack-Port1/1 # interface Stack-Port1/2 # interface Stack-Port2/1 # interface Stac

22、k-Port2/2 # interface Stack-Port3/1 # interface Stack-Port3/2 # interface 10GE1/0/1 port mode stack stack-port 1/1 port crc-statistics trigger error-down # interface 10GE1/0/2 port mode stack stack-port 1/1 port crc-statistics trigger error-down # interface 10GE1/0/3 port mode stack stack-port 1/2 port crc-statistics trigger error-down # interface 10GE1/0/4 port mode stack stack-port 1/2 port crc-statistics trigger error-d