SS-5061低比重及灌封胶硅橡胶.doc

SS-5061(有需要看分享者)低比重的灌封胶Low Specific Gravity Encapsulant Gel产品描述Product DescriptionSS-5061是一种混合比为1:1的双组分室温固化的弹性硅橡胶。它适用于对硅胶产品有低比重要求的情形。经室温下1小时固化，或于150下15分钟内固化后，所形成的弹性体可抵御气候、臭氧、潮湿、紫外线、高温。SS-5061 is a room temperature curing silicone RTV gel developed for applications requiring a low specific gravity silicone gel product. SS-5061 is a two part, 1:1 mix ratio silicone. Room temperature mixing of SS-5061 results in a cure time of 1 hour. SS-5061 can also be heat cured at 150C to yield a cure time of less than 15 minutes. When cured, the elastomer resists weathering, ozone, moisture, UV and high temperatures. 产品特点Product Features加成固化 Addition cure liquid优异的模压性能，可敷形于塑料、金属和玻璃材质 Excellent moldability and conformation to plastic, metal and glass parts混合比1:1，使用方便 Convenient 1:1 mix ratio典型应用Typical Applications电子元件减振、隔震或隔热 Electronic component vibration, shock and thermal insulation灌封 Potting and encapsulation防尘、防潮Dust and moisture protection电绝缘Dielectric insulation颜色：浅蓝色（可根据需求定制为其他颜色）Color: Light blue(Custom colors available upon request)固化机理Chemical cure system铂催化下的加成固化反应Platinum catalyzed, addition Cure System混合说明Mixing Instructions 最佳混合方式是手工按体积比1:1混合并进行脱气处理。也可使用自动设备进行混合及涂覆。The preferred method of mixing and application of SS-5061 is by hand using a 1:1 mix ratio by volume and then degassing. SS-5061 can also be mixed and dispensed through automatic equipment. 性能参数Typical Properties固化前 组分A 组分B黏度（厘泊）： 1,000 1,000比重： 0.76 0.76粘稠性（混合后）： 轻质液体釜中寿命（分，室温）： 3090%固化时间（分，室温）： 45表干时间（小时，室温）： 1表干时间（分，150）： 15UNCURED Part A Part BViscosity, cps 1,000 1,000Specific Gravity 0.76 0.76Consistency mixed: light liquidPot-life R.T.: 30 minutes90% cure R.T. 45 minutesCure time R.T.: 1 hourCure time 150 C 15 minutes固化后绝缘强度（千伏/毫米）： 10介电常数： 2.8耗散因数： 0.001体积电阻率： 1.0x1015热膨胀系数： 1.0x10-3Dielectric Strength, KV/mm 10Dielectric Constant 2.8Dissipation Factor 0.001 Volume Resistivity 1.0x1015Coefficient of Thermal Expansion 1.0x10-3固化深度与时间的关系Depth of cure vs time1小时内即可实现任意深度的完全固化。In 1 hour, any depth of application filled with this product will be cured and fully encapsulated. 温度范围Service Temperature -45至250-45 to 250固体成分Solids98%，不含溶剂成分。98% solids, contains no solvents操作注意Handling precautions 与以下物质接触不利于固化过程：锡催化体系的橡胶组分、含硫化合物、叠氮化合物、亚胺化合物、乳胶手套、胺类化合物等Avoid contact with tin cured RTVs, sulphur compounds, azides, imides, latex rubber gloves, and amines as cure system can be deactivated附着力Adhesion对塑料、金属和常见基底的直接附着力低。This product offers minimal primerless adhesion to plastics, metals and typical substrates.使用限制 Limitations不可使用于汽缸盖垫片及燃油或溶剂浸泡的环境下。待完全固化后再使用工件。Do not use product on head gaskets, fuel or solvent immersion applications. Allow to fully cure before putting assembly into service. 包装规格PackagingSS-5061采用两支装。有50毫升、453克（1磅）、5.44千克（12磅）、27.22千克（60磅）等规格。SS-5061 is available in 50 ml.dual syringes, one pound, 12 lb. and 60 lb. kits. 操作及安全Handling and safety 暂不使用时将容器密封以延长保存期。避免孩童接触。未固化的产品对眼睛和皮肤有刺激作用。参考安全技术说明书（MSDS）。For maximum shelf life, keep containers sealed when not in use. Keep out of the reach of children. Uncured sealant irritates eyes and skin. Refer to MSDS.适用标准Applicable standards 符合GM（通用汽车制造公司标准）低挥发物要求。Conforms to GM low volatility requirements.保质期Shelf-life自发货日起，厂家承诺密封条件下1年的保质期。 请在低于22（70F）且干燥环境下贮存。Sealed containers are guaranteed for 1 year from the ship date when stored in a cool dry area below 70 F.有限承诺Limited warranty 此处提供的表述、技术数据及推荐意见信息是根据我们的测定如实提供的，并相信是准确且可靠的。但由于使用本公司产品的条件和方法非我们所能控制，因此本信息不能取代客户进行的操作，以承诺产品是安全、有效、并完全满足于特定的最终用途。用户应根据自身情况及试验来判断产品是否达到使用效果，并自行承担产品的使用责任及风险。我们所提供的使用建议，不得被视为侵犯任何专利的误导。我们的唯一保证，是产品在发货时满足的销售规格及剂量。如果该保证不能兑现，您所能获得的补偿仅限于退还被保证产品的购货价款或重新更换。特别声明，对于其它特别用途或商品的任何明示或暗示的适用性不作任何保证。我们对买家或第三方的任何事故或由此引起的损失不负任何责任。我们对在本文中未作出陈述的其他书面说法也不作承诺保障。All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as warranty, either expressed or applied. User shall rely on his own information and tests to determine suitability of the product for the intended use, and the user assumes all risk and liability resulting from the use of this product. Manufacturers sole responsibility shall be to replace that portion of product of the manufacturer proves to be defective. Manufacturer shall not be liable to the buyer or any third party for injury, loss or damage directly or indirectly resulting from the use of, or inability to use, the product. Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding by the manufacturer.该产品并未经过黏膜组织、破损皮肤、血液、或植入人体内等领域的测试，也不推荐使用于以上领域。This product has not been tested for, and is ther