1044高速转接套齿样件检验报告.doc

dabg-zb-91注：粗线框内由东安动力填写，本报告一式四联。区 分样品种类送检日期： 年 月 日判定日期： 年 月 日样件检验报告新开发件半 成 品设计变更件成 品工程变更件改进产品关键重要一般 更改单日期： ；更改单编号： ；图面版本号：供方：重庆市江汇机械有限责任公司 (第 1 次送样)样品数量：5件 试生产产量：机型：dabs10-4 件号：bs10-4-1701044 件名：高速转接套齿 样品重量： 146 g报告内容：尺寸检验 材质报告 性能试验 耐久试验 统计资料 外观件报告 其它送审理由：新开发件样件标识方法及编号使用材料核准审核填表粉末冶金smf5040-jis z 2550-1983东安综合判定核准审核填表合格判定内容：条件合格不合格简图及说明：按规范要求项目所作成之材料、成分、物性、性能试验等报告难以记载本报告以任意格式附纸于后。粗线框内由da填写。检 验 报 告（续页）dabg-zb-91注：粗线框内由东安动力填写机型：dabs10-4 件号：bs10-4-1701044 名称：高速转接套齿序号检验项目规 格12345678910判定1距离20.50.120.5420.5620.5420.5620.4620.4620.5420.5620.5620.5620.5340.001442宽度5.60.055.585.585.545.625.625.545.545.605.565.605.5780.000923宽度54.985.024.984.985.025.005.025.024.984.984.9980.000364深度77.067.066.986.987.07.06.966.987.047.047.010.001225厚度200.2520.1219.8420.1419.8420.2020.2019.9019.9019.8420.2020.0180.024766端面粗糙度ra3.23.03.02.92.93.03.02.92.92.62.62.880.02167跳动0.10.080.090.080.090.080.080.080.090.090.090.0850.000038内花键大径粗糙度ra6.35.65.45.65.66.25.25.45.25.45.25.480.08169距离0.50.150.400.540.540.520.520.400.460.460.520.540.490.0028210端面粗糙度ra1.6（两侧）1.221.21.241.361.361.261.221.221.241.361.2680.0038611端面跳动0.10.090.070.080.090.070.080.080.070.090.080.080.0000612厚度160.0516.0315.9715.9716.0316.0116.0115.9716.0115.9816.0115.9990.0005313直径50.353.4653.5253.4653.4653.5853.5853.5053.5253.4653.5253.5060.00214油槽深度1.5（两侧）1.51.51.481.481.521.481.501.51.481.521.4960.0002215油槽宽度6（两侧）6.045.965.966.046.006.05.965.966.026.025.9960.0010216油槽过渡圆弧r5（两处）5.024.985.004.985.025.005.025.024.985.005.0020.0002817斜角20（3处）20.219.819.819.820.020.219.820.220.019.819.960.030418距离18（3处）18.0417.9618.0018.0017.9817.9618.0418.1418.0018.0218.0140.0024819宽度7（3处）6.847.006.906.846.847.026.906.987.047.006.9360.00582检 验 报 告（续页）dabg-zb-91：粗线框内由东安动力填写机型：dabs10-4 件号：bs10-4-1701044 名称：高速转接套齿序号检验项目规 格12345678910判定20角度20（3处）19.620.219.819.820.220.219.820.220.019.619.940.056421圆弧r1.2（六处）1.141.181.261.041.261.201.181.041.261.161.1720.0060222倒角c0.5 (六处)0.500.480.480.520.560.500.500.420.440.500.490.0013823外花键大径57.657.5857.5657.5857.5257.5657.5257.5657.5857.5657.5657.5580.0004424外花键小径53.252.9853.1052.9853.1053.0653.1053.1052.9853.0853.1053.0580.0027625公法线长度22.4922.47522.4522.4822.48522.4522.47522.4522.4822.47522.48522.47050.0001926外花键综合公差0.050.030.040.040.030.040.030.040.030.040.040.0360.0000227内花键大径2827.96527.98027.98527.97527.96027.98027.96527.96527.98027.96527.9720.0000728内花键小径2626.0826.1026.0826.1226.0626.0826.1226.1226.0626.1226.0940.0005629内花键跨棒距24.06824.08524.10524.1024.12524.0924.08524.0924.11524.10524.11524.10150.0001830内花键综合公差0.050.030.030.040.040.030.030.040.030.030.040.0340.0000231材料组成fec0.30.8cu13ni 28其它132材料密度6.8g/cm33高频淬火深度20.3检 验 报 告（续页）dabg-zb-91：粗线