M74HC4052.pdf

1/12July 2001 ILOW POWER DISSIPATION: ICC = 4A(MAX.) at TA=25C ILOGIC LEVEL TRANSLATION TO ENABLE 5V LOGIC SIGNAL TO COMMUNICATE WITH 5V ANALOG SIGNAL ILOW “ON“ RESISTANCE: 70 TYP. (VCC - VEE = 4.5V) 50 TYP. (VCC - VEE = 9V) IWIDE ANALOG INPUT VOLTAGE RANGE: 6V IFAST SWITCHING: tpd = 15ns (TYP.) at TA = 25 C ILOW CROSSTALK BETWEEN SWITCHES IHIGH ON/OFF OUTPUT VOLTAGE RATIO IWIDE OPERATING SUPPLY VOLTAGE RANGE (VCC - VEE) = 2V TO 12V ILOW SINE WAVE DISTORTION: 0.02% at VCC - VEE = 9V IHIGH NOISE IMMUNITY: VNIH = VNIL = 28 % VCC (MIN.) IPIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4052 DESCRIPTION The M74HC4052 is a dual four-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology and it is pin to pin compatible with the equivalent metal gate CMOS4000B series. It contains 8 bidirectional and digitally controlled analog switches. A built-in level shifting is included to allow an input range up to 6V (peak) for an analog signal with digital control signal of 0 to 6V. VEE supply pin is provided for analog input signals. It has an inhibit (INH) input terminal to disable all the switches when high. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND. A and B control inputs select one channel out of four in each section. All inputs are equipped with protection circuits against static discharge and transient excess voltage. M74HC4052 DUAL 4-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER PIN CONNECTION AND IEC LOGIC SYMBOLS ORDER CODES PACKAGETUBET derate to 300mW by 10mW/C from 65C to 85C RECOMMENDED OPERATING CONDITIONS SymbolParameterValueUnit VCCSupply Voltage-0.5 to +7V VCC - VEESupply Voltage -0.5 to +13V VIControl Input Voltage-0.5 to VCC + 0.5 V VI/OSwitch I/O VoltageVEE -0.5 to VCC + 0.5V ICKControl Input Diode Current 20mA IIOKI/O Diode Current 20mA ITSwitch Through Current 25mA ICC or IGNDDC VCC or Ground Current 50mA PDPower Dissipation500(*)mW TstgStorage Temperature-65 to +150C TLLead Temperature (10 sec) 300C SymbolParameterValueUnit VCCSupply Voltage 2 to 6V VEESupply Voltage-6 to 0V VCC - VEESupply Voltage2 to 12V VIInput Voltage0 to VCC V VI/OI/O VoltageVEE to VCC V TopOperating Temperature-55 to 125C tr, tf Input Rise and Fall TimeVCC = 2.0V0 to 1000 nsVCC = 4.5V0 to 500 VCC = 6.0V 0 to 400 M74HC4052 4/12 DC SPECIFICATIONS SymbolParameter Test ConditionValue Unit VCC (V) VEE (V) TA = 25C-40 to 85C-55 to 125C Min.Typ.Max.Min.Max.Min.Max. VIHCHigh Level Input Voltage 2.01.51.51.5 V4.53.153.153.15 6.04.24.24.2 VILCLow Level Input Voltage 2.00.50.50.5 V4.51.351.351.35 6.01.81.81.8 RONON Resistance4.5GNDVI = VIHC or VILC VI/O = VCC to VEE II/O 2mA 85180225270 4.5-4.555120150180 6.0-6.050100125150 2.0GND VI = VIHC or VILC VI/O = VCC or VEE II/O 2mA 150 4.5GND70150190230 4.5-4.550100125150 6.0-6.04580100120 RONDifference of ON Resistance between switches 4.5GNDVI = VIHC or VILC VI/O = VCC or VEE II/O 2mA 10303545 4.5-4.55121518 6.0-6.05101215 IOFFInput/Output Leakage Current (SWITCH OFF) 6.0GNDVOS = VCC or GND VIS = GND or VCC VI = VILC or VIHC 0.06 0.6 1.2 A 6.0-6.0 0.1 1 2 IIZSwitch Input Leakage Current (SWITCH ON, OUTPUT OPEN) 6.0GNDVOS = VCC or GND VI = VIHC or VILC 0.06 0.6 1.2 A 6.0-6.0 0.1 1 2 IIInput Leakage Current 6.0GNDVI = VCC or GND 0.1 0.1 1 A ICCQuiescent Supply Current 6.0GND VI = VCC or GND 44080 A 6.0-6.0880160 M74HC4052 5/12 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the ICs internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC SymbolParameter Test ConditionValue Unit VCC (V) VEE (V) TA = 25C-40 to 85C-55 to 125C Min.Typ.Max.Min.Max.Min.Max. I/OPhase Difference Between Input and Output 2.0GND25607590 ns 4.5GND6121518 6.0GND5101315 4.5-4.54 tPZL tPZH Output Enable Time 2.0GND RL = 1K 64225280340 ns 4.5GND18455668 6.0GND15384858 4.5-4.518 tPLZ tPHZ Output Disable Time 2.0GND RL = 1K 100250315375 ns 4.5GND33506370 6.0GND28435464 4.5-4.529 SymbolParameter Test ConditionValue Unit VCC (V) VEE (V) TA = 25C-40 to 85C-55 to 125C Min.Typ.Max.Min.Max.Min.Max. CINInput Capacitance5.05101010pF CI/O Common Terminal Capacitance 5.0-5.019404040pF CI/O Switch Terminal Capacitance 5.0-5.07151515pF CIOS Feed Through Capacitance 5.0-5.00.85222pF CPDPower Dissipation Capacitance (note 1) 5.0GND71pF M74HC4052 6/12 ANALOG SWITCH CHARACTERISTICS (GND = 0V; TA = 25C) (*) Input COMMON Terminal, and measured at SWITCH Terminal (*) Input SWITCH Terminal, and measured at common Terminal NOTE: These characteristics are determined by the design of the device. SymbolParameterTest ConditionValueUnit VCC (V) VEE (V) VIN (Vp-p) Typ. Sine Wave Distortion 2.25-2.254 fIN = 1 KHz RL = 10 K, CL = 50 pF 0.025 %4.5-4.580.020 6.0-6.0110.018 fMAXFrequency Response (Switch ON) (*) 2.25-2.25Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50, CL = 10 pF, fIN = 1KHz sine wave 120 MHz4.5-4.5190 6.0-6.0200 fMAXFrequency Response (Switch ON) (*) 2.25-2.25Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50, CL = 10 pF, fIN = 1KHz sine wave 70 MHz4.5-4.5110 6.0-6.0140 Feedthrough Attenuation (Switch OFF) 2.25-2.25VIN is centered at (VCC - VEE)/2 Adjust input for 0 dBm RL = 600, CL = 50 pF, fIN = 1KHz sine wave -50 dB 4.5-4.5-50 6.0-6.0-50 Crosstalk (Control Input to Signal Output) 2.25-2.25Adjust RL at set up so that IS = 0A. RL = 600, CL = 50 pF, fIN = 1KHz square wave 60 mV 4.5-4.5140 6.0-6.0200 Crosstalk (between any two Switches) 2.25-2.25Adjust VIN to obtain 0dBm at input RL = 600, CL = 50 pF, fIN = 1KHz sine wave -50 dB4.5-4.5-50 6.0-6.0-50 M74HC4052 7/12 SWITCHING CARACTERISTICS TEST CIRCUIT CROSSTALK (control to output) BANDWIDTH AND FEEDTHROUGH ATTENUATIONCROSSTALK BETWEEN ANY TWO SWITCHES M74HC4052 8/12 SWITCHING CHARACTERISTICS WAVEFORM CHANNEL RESISTANCE (RON) ICC (Opr.) M74HC4052 9/12 DIM. mm.inch MIN.TYPMAX.MIN.TYP.MAX. a10.510.020 B0.771.650.0300.065 b0.50.020 b10.250.010 D200.787 E8.50.335 e2.540.100 e317.780.700 F7.10.280 I5.10.201 L3.30.130 Z1.270.050 Plastic DIP-16 (0.25) MECHANICAL DATA P001C M74HC4052 10/12 DIM. mm.inch MIN.TYPMAX.MIN.TYP.MAX. A1.750.068 a10.10.20.0030.007 a21.650.064 b0.350.460.0130.018 b10.190.250.0070.010 C0.50.019 c145 (typ.) D9.8100.3850.393 E5.86.20.2280.244 e1.270.050 e38.890.350 F3.84.00.1490.157 G4.65.30.1810.208 L0.51.270.0190.050 M0.620.024 S8 (max.) SO-16 MECHANICAL DATA PO13H M74HC4052 11/12 DIM. mm.inch MIN.TYPMAX.MIN.TYP.MAX. A1.20.047 A10.050.150.0020.0040.006 A20.811.050.0310.0390.041 b0.190.300.0070.012 c0.090.200.0040.0089 D4.955.10.1930.1970.201 E6.26.46.60.2440.2520.260 E14.34.44.480.1690.1730.176 e0.65 BSC0.0256 BSC K0808 L0.450.600.750.0180.0240.030 TSSOP16 MECHANICAL DATA cE b A2A E1 D 1 PIN 1 IDENTIFICATION A1 L K e 0080338D M74HC4052 12/12 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which