外文原文.pdf_第1页
外文原文.pdf_第2页
外文原文.pdf_第3页
外文原文.pdf_第4页
全文预览已结束

外文原文.pdf.pdf 免费下载

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

Research on the Dual Meshing Silent Chain Drive Xue Yunna1 Shen Xuehui1 Wang Yong2 1 Department of Mechanical Engineering Shandong Institute of Light Industry 2 Department of Mechanical Engineering Shandong University xueyunna shenxuehui sd meywang Abstract In order to reduce the polygon action the dual meshing silent chain is presented and this kind of silent chain mechanism is designed which comprises the dual meshing silent chain and new kind of sprockets with modified involute tooth profile At the beginning of a meshing circle the inner tooth profile meshes with the sprocket tooth profile At the middle of a meshing circle both sides of the silent chain contact with the sprocket tooth profile At last the dual meshing silent chain depends on its outer tooth profile to wind around the sprocket The meshing theory of the dual meshing silent chain drive and the modified method of the involute sprockets are researched The polygon action of the dual meshing silent chain drive and the conventional silent chain drive is compared The result shows that the amplitude of polygon action of the dual meshing silent chain mechanism reduces 94 percent and the dual meshing silent chain drive basically eliminates the influence of the polygon action Keywords dual meshing silent chain modified involute olygon action I INTRODUCTION In conventional silent chain drive the sprocket tooth profile is straight In the meshing progress of silent chain and sprockets only the single side of tooth profile meshes with the straight tooth profile of the sprocket to transmit the movement and the power When the link plate meshes with the sprocket engagement contact happens once a time In the following meshing process there is not relevant movement between the link plate and the sprocket Then when the next link plate meshes with the sprocket the engagement contact happens again 1 In the recent years the involute tooth profile of sprockets is more widely used because of the small engagement contact and the conjugate engagement compared with the conventional sprockets The change of the link plate structure and the study of new link plate profile were also presented in order to reduce the polygon action and meshing impact 2 Zhang investigated a new silent chain mechanism with rocker pins 3 Meng and Feng built a parametric simulation model by ADAMS 4 However the change of the link plate structure results in the complexity of the processing technique Not only in the conventional silent chain drive but also in the silent chain drive with the conventional chain and the involute tooth profile sprockets the center line of the chain tight side is alternately tangential and secant to the pitch circle So the up and down movement of tight side develops the polygon action and the transverse vibration Further more the meshing impact at the meshing moment is large Thus the dual meshing silent chain drive is put forward which can reduce the polygon action and the meshing impact The dual meshing silent chain mechanism is composed of the dual meshing silent chain and the new kind of sprockets with the modified involute tooth profile In the dual meshing silent chain drive at the beginning of a meshing circle the inner straight tooth profile of the silent chain engages with the sprocket profile With the continuing of the meshing progress both sides of the silent chain contact with the sprocket profile In the end the dual meshing silent chain depends on its outer tooth profile to wind around the sprocket II DUAL MESHING SILENT CHAIN A Reduction of the polygon action When the conventional silent chain meshes with the conventional sprocket or the involute sprocket the distance between the tight side of the chain and the sprocket center is alternately changing with the continuing of the meshing process The reason of the position variation is that the tight side is tangential and secant to the sprocket pitch circle Then if the secant state is avoided and the tangential state exits in the whole meshing process the polygon action can be avoided or reduced Based on the idea the dual meshing silent chain is put forward Fig 1 shows the theory of reducing the polygon action about the dual meshing silent chain As shown in the Fig 1 a the hidden line denotes the tight side of the conventional silent chain and the real line denotes the tight side of the dual meshing silent chain The left tooth profile of the sprocket tooth 3 meshes with the right tooth profile of the joint A In the conventional silent chain the right tooth profile of the joint A is the outer tooth profile of the link 1 But in the dual meshing silent chain the right tooth profile of the joint A is the inner tooth profile of the link 2 Because the inner tooth profile of link plate is profiled to parallel and project outward of the outer tooth profile as the dual meshing silent chain is stretched into a line So in the dual meshing silent chain drive the tight side of the chain can still be tangential to the sprocket pitch circle at the position shown in the Fig 1 a by defining the special relation about the inner and outer tooth profile The special relation can be shown in the Fig 1 b rdi denotes the radius of the locating circle of the inner tooth 2010 International Conference on Computing Control and Industrial Engineering 978 0 7695 4026 9 10 26 00 2010 IEEE DOI 10 1109 CCIE 2010 188 281 2010 International Conference on Computing Control and Industrial Engineering 978 0 7695 4026 9 10 26 00 2010 IEEE DOI 10 1109 CCIE 2010 188 280 profile and rd denotes that of the outer tooth profile rd subtracted from rdi gives f which is related to the amplitude of the polygon action Because of the static characteristics of chain drive the position of joint A is influenced by that of joint B Thus the parameter f is also related to the movement distance of the tight side when the center of the joint A keeps on the line tangential to the sprocket pitch circle 5 So the parameter f may be satisfied with some condition to make the inner tooth profile and the outer tooth profile all mesh with the sprocket tooth Fig 1 Theory of reducing the polygon action B Link plate of dual meshing silent chain The tooth profile of the dual meshing link plate is shown in Fig 2 The inner tooth profile is completely under the line through the two joint center of the link plate The angle of the tooth profile is still equal to 60 The normal space f between the inner tooth profile and the symmetrical line of the outer tooth profile can be calculated as 2 cos 2 sin lhf 1 Where h is the amplitude of the polygon action and l is defined as l l1 l2 2 Where l1 is the moving distance of the tight side when the chain winds around the sprocket l2 is that of the tight side when the chain does not wind around the sprocket but move along the line tangential to the sprocket pitch circle in the process when the sprocket rotates a half of the pitch angle The coordinate of the link plate is shown in Fig 2 where the axis of abscissa and the rack midline of the outer tooth profile are along a same line The rack midline of the inner tooth profile is underneath that of the outer tooth profile and the distance h is defined as 2 sin fh 3 Fig 2 Link plate of dual meshing silent chain C Amplitude of the polygon action In the conventional silent chain drive as the chain tight side is tangential to the sprocket the vertical distance between the central line of the chain tight side and the sprocket center is the radius of the pitch circle When the sprocket rotates about a half of the pitch angle as the chain tight side is secant to the sprocket pitch circle the vertical distance is the radius of the addendum circle So in the whole drive process the distance is alternately changing between the radius of the pitch circle and that of the addendum circle In the conventional silent chain drive the amplitude of the polygon action is as follows 2 2 2sin 180 2tan 180 a hdd pp zz 4 Where d is the diameter of the pitch circle and da is that of the addendum circle p is the pitch of the silent chain drive and z is the tooth number of the sprocket Thus when the conventional chain meshes with the conventional or the involute sprocket the fluctuation value of the up down movement of the chain tight side is not greater than h D Moving distance of the tight side When the dual meshing silent chain meshes with the conventional sprocket the engaging link is rooted on and rotates with the sprocket at last So the engaging link is not in a same line with the next link Then as the chain does not wind around the sprocket but keeps moving the silent chain drive is same to the gear and rack drive The gear rotation drives the rack moving The relation between the sprocket rotating angle and the rack moving distance is linear Otherwise the relation is not linear because the chain is needed to wind around the sprocket In the process when the sprocket rotates about the angle 2 it is supposed that the engaging joint A is always on the line tangential to the sprocket pitch circle and the moving distance of the joint A is p l The relationship of the moving parameter about two 282281 joints center A and B of the engaging link from the position A1B1 to the position A2B2 is shown in Fig 3 r x y x l 1 B 2 B r 2 1 2 A p l 1 A p Fig 3 Moving parameter about two joints center A and B In Fig 3 in order to satisfy the requirement that the tight side is always tangential to the sprocket pitch circle and the chain can wind around the sprocket the motion type of joint A and joint B is different The joint B rotates with the sprocket from the position B1 to the position B2 The joint A moves along the line tangential to the sprocket pitch circle from the position A1 to the position A2 In the process the rotation angle of the sprocket is equal to 2 The distance of the point A1 and the point A2 is defined as lp The distance of the point B1 and the point B2 is defined as lx The angle between the line A1B1 and the line A2B2 is defined as 1 The parameter relationship of the distance lx and lp the angle 1 and the abscissa of point A2 is as follows 2 12 212 2 sin 2 arcsinsin 2 coscos 2 x x Ax pA ld lp xpl lpx 5 When the chain does not wind around the sprocket but keep moving along the line tangential to the sprocket pitch circle the meshing type of the chain and the sprocket is conjugate and the moving distance lp1 can be expressed as 12px lr 6 Where rx is the radius of the tangential circle When 2 is equal to the a half of the pitch angle the distance lp is equal to l1 and the distance lp1 is equal to l2 From equation 1 5 and 6 l can be defined as 31901 cos arcsin tan 222 x lppr Z 7 III NEW TYPE OF SPROCKET The involute sprocket can reduce the meshing impact When the dual meshing silent chain meshes with the involute sprocket the engaging link may interfere with the addendum of the involute sprocket So in order to avoid the interference the involute sprocket must be modified to correctly mesh with the dual meshing silent chain The modified method can be got by the envelope theory 6 Based on the envelope theory the sprocket tooth profile can be achieved according to the inner tooth profile and its law of motion The function of the movement distance and the sprocket rotation angle can be derived from equation 5 The pitch angle of the sprocket is equally divided and the corresponding position of the inner tooth profile can be received A number of the position of the inner tooth profile is shown in Fig 4 In Fig 4 the heavy line denotes the original involute tooth profile and the hatching denotes the sprocket tooth Fig 4 Modification of the involute sprocket As shown in the Fig 4 in the position 0 the inner tooth profile is tangential to the sprocket involute tooth profile When the inner tooth profile reaches position 1 it interferes with the sprocket tooth profile and cuts a part of the sprocket tooth The inner tooth profile is more close to the addendum interference part is larger In position 0 cutting rate is equal to zero and in the last position mn cutting rate fmn is largest The largest cutting rate fmn that is the maximum modification is a function of the sprocket tooth number and the pitch When p 6 35mm the maximum modification fmn of different tooth number is shown in Table 1 When z 20 the maximum modification fmn of different pitch is shown in Table 2 From Table 1 and Table 2 the result shows that the maximum modification is increased with the tooth number decreasing and the pitch increasing Table 1 Maximum modification when p 6 35mm Teeth number 20 30 40 50 60 70 80 mn f um 4 2 1 9 1 1 0 7 0 5 0 4 0 3 Table 2 Maximum modification when z 20 Sprocket Pitch mm 9 525 12 7 15 875 19 05 mn f um 6 3 8 4 10 5 12 7 Sprocket Pitch mm 25 4 31 75 38 1 mn f um 17 0 21 2 25 4 dedendum addendum n m 1 0 m n f 283282 IV REDUCTION OF POLYGONG ACTION The special position of the dual meshing silent chain drive in the meshing progress is illustrated in Fig 5 In the figure the smallest circle denotes the meshing point of the link and the sprocket In Fig 5 a the tight side is tangential to the sprocket pitch circle and the inner and outer tooth profile of the joint B are all meshing with the left side of the sprocket tooth 2 Then the joint B rotates with the sprocket The tight side of the chain falls down with the joint B until the inner tooth profile of the joint A meshes with the left side of the sprocket tooth 1 that is the chain and the sprocket meshes on the position shown in Fig 5 b At that time the amplitude of polygon action is largest and the tight side does not fall down but moves up by the continuing meshing with the sprocket Later in Fig 5 c the tight side is tangential to the sprocket pitch circle again Fig 5 Special position of the dual meshing silent chain drive Thus the amplitude of the polygon action of the dual meshing silent chain drive is the vertical distance between the tight side and the sprocket center Through the analysis the amplitude of the dual meshing silent chain drive is 0 01mm and that of the conventional silent chain drive is 0 178mm when 35 6 p mm and 28 Z The amplitude comparison of the polygon action of the two silent chain drives is shown in Fig 6 in a meshing circle Fig 5 Amplitude comparison of polygon action when p 6 35 and z 28 between two silent chain drives V CONCLUSION In the paper the tooth profile of silent chain to reduce po

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论