用十字螺丝刀进行操作.pdf

MEC 9003 Compact Desktop Wall mounted Embedded Box PC Version A0 Announcement What contained in this User Manual does not represent the commitments of EVOC Company EVOC Company reserves the right to revise this User Manual without prior notice and will not be held liable for any direct indirect intended or unintended losses and or hidden dangers due to installation or improper operation EVOC is a registered trademark of EVOC Intelligent Technology Co Ltd All trademarks registered trademarks and trade names used in this User s Guide are the property of their respective owners EVOC Intelligent Technology Co Ltd 2009 Copyright Reserved No part of this manual may be reproduced in any form or by any means such as in electronic or mechanical way without permission in writing from EVOC Safety Instructions 1 Please carefully read the users manual before handling the product 2 Before inserting removing or re configuring the boards please firstly disconnect the AC power or unplug the AC power cable from the power source to prevent damage to the product and ensure your personal safety 3 Before removing this product please firstly unplug the AC cable from power source 4 When inserting or removing boards please firstly unplug the AC power cable from power sources 5 Before connecting or disconnecting any signal cable make sure all power cables are unplugged in advance 6 To avoid unnecessary damage caused by turning on off computer frequently wait at least 30 seconds before re turning on the computer 7 All the operations such as upgrade remove or installation shall be implemented on the ESD worktable because some exactitude components are sensitive to electrostatic discharge ESD 8 If there s no ESD worktable please take the following steps to prevent damage from electrostatic discharge ESD a Wear a antistatic wrist strap and connect it with the metal part of the corresponding product b Always touch the metal chassis or frame before touching any components c Keep part of your body in contact with the metal chassis to discharge the static while handling components d Avoid all unnecessary movement e Hold the components especially the boards by the edges f Place the components on a grounded static free operating platform Use a conductive foam pad if available not the component wrapper g Do not let the components slide on the operating platform 9 Use cross head screwdriver to operate A magnetic screwdriver is recommended magnet helps to collect screws Do not leave any tools or screws inside the chassis 10 Assure abundant cooling and ventilation ContentsContents Chapter 1 Product Introduction 1 Overview 1 Main Functions 1 Main Performance 3 Requirements of Transportation and Storage 4 Troubleshooting 4 Chapter 2 Installation 5 Product Outline 5 Product Dimension Drawing 6 External IO Interface 7 Assembly Explanation 8 Critical Part Installation 9 Chapter 3 BIOS Setup 11 Chapter 4 Installation of Drivers 12 Chapter 1 Product Introduction MEC 9003 1 Chapter 1 Product Introduction Overview MEC 9003 is a sort of compact desktop wall mounted embedded original box PC with single board structure it could support 9 motherboard of EVOC all the I O interfaces are front installed on the chassis and supports chassis with four PCI expansion slots The whole chassis adopts high quality steel board which enables the PC possesses capabilities like dust proof heat dissipation and EMC Its motherboard adopts Intel GM945G ICH7 chipset supports LGA775 encapsulated with Pentium D and Core TM 2 Duo FSB 800 1066MHz processors on board chipset integrates GM950 graphic processing core supports dual display sharing memory with independent video memory above 128M and supports dual VGA independent dual display function This product is another embedded original box PC of MEC 9000 series which could be widely used in industries like TVM machine of metro AFC system ATM industrial control and building automation system Main Functions CPU Intel Core TM 2 Duo E4300 Intel Core TM 2 Duo E6400 System Chipset Intel GM945G Intel ICH7 R chipset System Storage The motherboard provides two standard DDR 400 533 667MHz memory slots with memory capacity up to 4GB Chapter 1 Product Introduction 2 MEC 9003 LAN Function One 10 100 1000Mbps Ethernet controller providing with high speed and stable network platform selection Video Function Graphic controller integrates in Intel 945 chipset and its display memory shared with system memory Possess Adopt Intel 4 th generation graphic engine with 400MHz operating frequency and the maximum resolution is 2048 1536 Adopt DVMT which allocates display memory according to requirement with maximum sharing memory up to 256MB Two VGAinterfaces supporting dual display Audio Function Support Intel HD Audio high definition audio output which provides excellent sound effect Expansion Bus Provide three PCI slots and one PCI E X1 slot directly and is convenient to expand devices I O Interface Eight USB2 0 interfaces Ten RS 232 interfaces among which COM2 supports RS 485 RS 422 mode Two VGAinterfaces Chapter 1 Product Introduction MEC 9003 3 Aset of audio interfaces One PS 2 keyboard and mouse interface One 10 100 1000Mbps LAN port One high speed parallel port supporting SPP EPP ECP specification Power 350W ATX power Main Performance Mechanical Dimension Weight and Environment Dimensions 410 00 mm W x 170 00 mm H x 353 00mm D Weight Net Weight 10 90Kg Operating Temperature 10 55 Operating Humidity 40 RH 90 Non operating Temperature 20 70 EMC Limit of radio disturbance is compliant with GB9254 1998 class A Harmonic Current is compliant with GB T 17626 7 1998 Immunity to disturbance is compliant with GB T 17626 5 1998 level 2 Reliability MTBF 50000h MTTR 0 5h Safety Meet the requirement of GB 4943 Chapter 1 Product Introduction 4 MEC 9003 Environmental and Mechanical Adaptability Anti vibration amplitude 5 200Hz 1 0mm acceleration 1 0g Anti shock acceleration 10g duration 11ms Requirements of Transportation and Storage Transportation Well packaged products suit for transportation by truck ship and plane During transportation products should not be put in open cabin or carriage When transshipping in route products should not be stored in the open without protection from the atmospheric conditions Products should not be transported together with inflammable explosive and corrosive substances and are not allowed to be exposed to rain snow and liquid substances and mechanical force Storage Products should be stored in package box when it is not used And the warehouse temperature should be 0 C 40 C and relative humidity is 20 85 In the warehouse there shall not be harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box should be over ground at least 10cm height and 50cm away from wall thermal source and vent Troubleshooting Please refer to Common Trouble Analysis and Treatment of Industrial Control Computer for a detailed description of the troubleshooting Chapter 2 Installation MEC 9003 5 Chapter 2 Installation Product Outline Chapter 2 Installation 6 MEC 9003 Product Dimension Drawing 170 00 353 00 310 00 21 50 418 06 425 06 154 00 6 94 410 00 418 06 154 06 9 00 R2 50 Unit mm Chapter 2 Installation MEC 9003 7 External IO Interface 1 Mouse Keyboard Interface 2 VGAInterface 3 Parallel Port 4 VGAInterface 5 2USB LAN Compound Interfaces 6 4 USBs 7 Audio Interface 8 CD ROM 9 Power Switch 10 19 COMs 20 2 USBs Chapter 2 Installation 8 MEC 9003 Assembly Explanation 1 Chassis 2 Fixed Bracket 1 3 I O Bracket 4 Fixed Bracket 2 5 Motherboard 6 LED Board 7 CD ROM Bracket 8 Dust proof Bracket 9 Switch 10 CD ROM 11 Cover 12 Power 13 Hard Disk Components 14 Fan Components 15 Batten Chapter 2 Installation MEC 9003 9 Critical Part Installation 1 Installation of Motherboard After installing the CPU radiator on to the motherboard fix the motherboard onto the fixation studs with screws according to the screw holes on the motherboard As shown in the figure 2 Installation of Power Fix the power through the chassis with screws interiorly adopt screws to fix the power on to the internal studs within the chassis Chapter 2 Installation 10 MEC 9003 3 Installation of CD ROM and Hard Disk 1 Adopt M4 sunk header screws to fix the hard disk shock absorption pad onto the CD ROM bracket 2 Fix the CD ROM within the CD ROM bracket 3 Fix the hard disk within the hard disk bracket 4 Fix the hard disk bracket with hard disk onto the hard disk shock absorption pad Pay attention to the installation direction of CD ROM and hard disk and the direction of the interfaces Chapter 3 BIOS Setup MEC 9003 11 Chapter 3 BIOS Setup For more information about BIOS setup please refer to our AMI BIOS Setup Guide Chapter 4 Installation of Drivers MEC 9003 12 Chapter 4 Installation of Drivers Regarding the installation of the driver program of the product please refer to the CD of associated PC Please visit for more information 声明声明 本手册包含的内容并不代表本公司的承诺 本公司保留对此手册更改的权 利 且不另行通知 对于任何因安装 使用不当而导致的直接 间接 有意或无 意的损坏及隐患概不负责 EVOCEVOC 是研祥智能科技股份有限公司的注册商标 本手册所涉及到的其他商 标 其所有权为相应的产品厂家所拥有 研祥智能科技股份有限公司 2009 版权所有 违者必究 未经许可 不得 以机械 电子或其它任何方式进行复制 安全使用小常识安全使用小常识 1 产品使用前 务必仔细阅读产品说明书 2 为避免人体被电击或产品被损坏 在每次对板卡进行拔插 重新装配或配 置前 须先关闭交流电源或将交流电源线从电源插座中拔掉 3 在需对产品进行搬动时 务必先将交流电源线从电源插座中拔掉 4 当产品需增加 减少板卡时 务必先拔掉交流电源 5 当需连接或拔除任何信号线前 须确定所有的电源线事先已被拔掉 6 为避免频繁开关机对产品造成不必要的损伤 关机后 应至少等待 30 秒后 再开机 7 如果要进行升级或拆装等动作 须在静电放电工作台上完成所有操作 因 为有些精密器件对静电放电 ESD 很敏感 8 如果没有静电放电工作台 可通过以下方法降低 ESD 可能造成的危害 a 戴上一条防静电腕带并与相应产品的金属部分相连 b 在触摸产品部件前 先触摸相应产品机箱上的金属壳 c 当插拔部件时 身体最好与产品的金属机箱保持接触 以释放静电 d 避免不必要的走动 e 拿产品部件 尤其是板卡 时仅拿住边缘 f 将产品部件置于一个接地的无静电的操作平台上 如果可能的话 使 用一块导电泡沫垫 非部件的包装材料 g 不要让部件在操作平台上滑动 9 用十字螺丝刀进行操作 最好是强力螺丝刀 带磁性 避免螺丝遗留在机 箱内 要注意的是 一定不要将工具或零件遗漏在机箱内 10 保证系统良好的散热与通风 目 录目 录 第一章 产品介绍 1 简介 1 主要功能介绍 1 主要性能指标 3 运输与贮存要求 4 常见故障处理 4 第二章 安装说明 5 产品外形图 5 产品安装尺寸图 6 外部 IO 接口 7 装配图 8 关键部件装配说明 9 第三章 BIOS 功能简介 11 第四章 驱动程序安装说明 12 第一章 产品介绍 MEC 9003 1 第一章 第一章 产品介绍 产品介绍 简介简介 MEC 9003 是一款采用单板架构紧凑桌上型 壁挂式嵌入式原装整机 可支持 研祥 9 寸主板 机箱前置所有的 I O 接口 支持 4 个 PCI 扩展槽的机箱 箱体采 用优质的金属钢板 整体具有良好的防尘 散热 EMC 性能 主板采用 Intel GM945G ICH7 芯片组 支持 LGA775 封装 Pentium D Core TM 2 Duo FSB 800 1066MHz 处理器 在板视频芯片组集成 GM950 图形处理核心 支 持双显示共享内存 128M 以上独立显存 支持双 VGA 的独立双显示功能 此款产品作为我公司 MEC 9000 系列中又一款嵌入式原装整机 可广泛应用 于地铁 AFC 系统的 TVM 机 银行 ATM 机 工业控制 楼宇自动化等行业 主要功能介绍 主要功能介绍 微处理器微处理器 Intel Core TM 2 Duo E4300 Intel Core TM 2 Duo E6400 系统芯片组系统芯片组 Intel GM945G Intel ICH7 R 芯片组 系统存储器系统存储器 主板提供两条标准DDR 400 533 667MHz 内存插槽 最大内存容量达4GB 网络功能网络功能 一个 10 100 1000Mbps 以太网控制器 为您提供高速稳定的网络平台选择 第一章 产品介绍 2 MEC 9003 显示功能显示功能 Intel 945G 芯片组内集成图形控制器 显示内存和系统内存共享 具有 采用Intel第四代图形引擎 400MHz工作频率 最大分辨率为2048 1536 采用动态显示内存管理技术 DVMT 根据需要分配显示内存 最大可共享 256MB 两个VGA接口 支持双显示 音频功能音频功能 支持 Intel HD Audio 高清音频输出 提供优质的声音效果 扩展总线扩展总线 直接提供三个 PCI 插槽和一个 PCI E X1 插槽 方便扩充设备 I OI O 接口 接口 八个 USB2 0 接口 十个RS 232 接口 其中COM2可支持RS 485 RS 422模式 两个 VGA 接口 一组音频接口 一个 PS 2 键盘鼠标接口 一个 10 100 1000Mbps 网口 一个高速并行接口 支持SPP EPP ECP 标准 电源电源 350W ATX 电源 第一章 产品介绍 MEC 9003 3 主要性能指标 主要性能指标 机械尺寸机械尺寸 重量与环境 重量与环境 外形尺寸 410 00 mm 宽 x 170 00 mm 高 x 353 00mm 深 重量 净重 10 90Kg 工作温度 10 55 湿热工作 40 RH 90 储存要求 20 70 电磁兼容性 电磁兼容性 无线电骚扰限值符合 GB9254 1998 标准中规定的 A 级 谐波电流符合 GB T 17626 7 1998 抗扰度符合 GB T 17626 5 1998 中规定的 2 级 可靠性 可靠性 平均无故障工作时间 MTBF 50000h 平均维修时间 MTTR 0 5h 安全性安全性 产品的安全性满足 GB 4943 的基本要求 机械环境适应性 机械环境适应性 抗振动 抗振动 5 200Hz 1 0mm 振幅 1 0g 加速度 抗冲击 10g 加速度 11ms 周期 第一章