解码板英文说明书.doc

Aptitude Instruction Aptitude Decoder of aptitude HW-2013 Instruction 2004-8CONTENTCHAPTTER 1 SummarizationCHARPTER 2 Panel introductionCHARPTER 3 Technical specificationsCHARPTER 4 Connection decoder with SystemCHARPTER 5 Connection decoder with DVRCHARPTER 6 Connection decoder with PTZ and camera Connection diagram of decoder and PTZ (AC24V), camera Lens (DC12V):CHARPTER 7 Address settingCHARPTER 8 communication protocol, Baud rate settingCHARPTER 9 PTZ and Camera Lens auto check itselfCHARPTER 10 Equipment InstallationCHARPTER 11 FAQCHARPTER 1SUMMARIZATION The decoder of aptitude is a type of front equipment with DVR. The DVR will control the PTZ, Camera Lens, Auxiliary switch and so on through the decoder of aptitude. The decoder of aptitude can assemble all kinds of multi-protocol DVR. Without setting a protocol, it will decode code automatic quickly according to inner code of protocol then it will control the front equipments. The simple decoder of aptitude has a group of function that controls every group of power of camera, brush, lamplight and so on. The decoder of aptitude is unsuitable for the place flammable and explosive. Be careful to select the suitable working voltage for PTZ and Camera Lens when the decoder connects them.CHARPTER 2 PANEL INTRODUCTIONNONameSpecification1CODE/POWERCommunication/power indicator light2RS-485The port of RS-485 communication3CAMERAIDDecimal address coding switch (The number of camera)4UP/DOWN/LEFT/RIGHTPan/tilt up/down/left/right5AUTOPan/tilt auto6P/T-COMPan/tilt com7P/T VOLTAGEPan/tilt voltage (AC24V)8ZOOM/FOCUS/IRIS/9LNES COM/10DC12V/END/11AUX IN/OUTWireless auxiliary switch in common12AC24VINPUT/13POWER ON/OFFPower switch14AC220V 50Hz/CHARPTER 3 Technical specificationsInput voltage : 24VAC10%Pan/tilt voltage: 24VAC/1.0ACamera voltage: 2-15VDC/250MaAuxiliary switch: 275VAC/7AControl signal type : Two core shield twisted linesCHARPTER 4 Connection decoder with system The decoder of aptitude adopts communication of RS-485 Bus-mastering. DATA+ is a port of 485+ sign; DATA- is a port of 485- sign. GND earth. The standard RS-485 equipment connects the decoder of aptitude with two core shield twisted lines. The line is not over 1500m.The farthest decoder should be a 120ohm of shunt between 485+ and 485- when several decoders connect each other. The diagram of connection as follows: CHARPTER 5 Connection decoder with DVR Connect terminal DATA+ to 485+, DATA- to 485-, GND to GND in correspondence between Rs232 / 485 converter and decoder. The diagram0 of connection as follows:CHARPTER 6 Connection decoder with PTZ and CameraConnection diagram of decoder and PTZ (AC24V), camera Lens (DC12V):Specification:1. Select value to be consistent with pan/tilt working voltage AC24V/AC220V through (P/T VOLTAGE)2. Auxiliary, lamplight and brush control switch is NO., user may adopt according to actual needs.CHARPTER 7 Address setting In order to distinguishing different decoders, we use different address coding. Coding switch consists of 6 switches. In address coding switch and camera number compared table as follows:(for 1 set switch to on; for 0 set switch to off)Camera Address coding switchCamera Address coding switchNumber1 2 3 4 5 6Number1 2 3 4 5 611 0 0 0 0 0331 0 0 0 0 120 1 0 0 0 0340 1 0 0 0 131 1 0 0 0 0351 1 0 0 0 140 0 1 0 0 0360 0 1 0 0 151 0 1 0 0 0371 0 1 0 0 160 1 1 0 0 0380 1 1 0 0 171 1 1 0 0 0391 1 1 0 0 180 0 0 1 0 0400 0 0 1 0 191 0 0 1 0 0411 0 0 1 0 1100 1 0 1 0 0420 1 0 1 0 1111 1 0 1 0 0431 1 0 1 0 1120 0 1 1 0 0440 0 1 1 0 1131 0 1 1 0 0451 0 1 1 0 1140 1 1 1 0 0460 1 1 1 0 1151 1 1 1 0 0471 1 1 1 0 1160 0 0 0 1 0480 0 0 0 1 1171 0 0 0 1 0491 0 0 0 1 1180 1 0 0 1 0500 1 0 0 1 1191 1 0 0 1 0511 1 0 0 1 1200 0 1 0 1 0520 0 1 0 1 1211 0 1 0 1 0531 0 1 0 1 1220 1 1 0 1 0540 1 1 0 1 1231 1 1 0 1 0551 1 1 0 1 1240 0 0 1 1 0560 0 0 1 1 1251 0 0 1 1 0571 0 0 1 1 1260 1 0 1 1 0580 1 0 1 1 1271 1 0 1 1 0591 1 0 1 1 1280 0 1 1 1 0600 0 1 1 1 1291 0 1 1 1 0611 0 1 1 1 1300 1 1 1 1 0620 1 1 1 1 1311 1 1 1 1 0631 1 1 1 1 1320 0 0 0 0 164CHARPTER 8 Communication protocol, Baud rate setting Coding switch possess 4 switches, they divide into protocol coding switch and Baud rate coding switch. Protocol coding switch consists of 1-2, changes the coding for select different protocol. Baud rate coding switch consists of 3-4.changes the coding for select different Baud rate. The setting of protocol diagram as follows: Coding switchBaud rate9600480024001200 The setting of Baud rate diagram as follows:Coding switchprotocolAUTOPELCO-DPANASONICHT-600NOProtocolRecommendatoryBaud rateRemark1CCR-20G4800PICASO2PELCO-SP9600PICO20003KTD-3129600PICO4PELCO-D96005PELCO-D240024006HT60048007PELCO-P96008PANASONIC96009RM110960010KTE-301RX9600KODICOM11KALATEL CYB9600GV-80012PICO2400480013YAAN480014HY960015PELCO-P4800MATRIX/CONTROL16KALATEL4800CHARPTER 9 PTZ and Camera Lens auto check itselfThe decoder of aptitude can check itself and can control PTZ, Camera Lens through coding switches. Power off. Coding switch 3,4 set ON, the others setOFF.Power on .The Len checks itself, the light works.FunctionAddress coding switchCode switch1234561234FOCUS+1000000011FOCUS-0100000011IRIS+0010000011IRIS-0001000011ZOOM+0000100011ZOOM_0000010011 Power off, all coding switch set OFF.Power on, the PTZ checks itself, the light works.FunctionAddress coding switchCode switch1234561234Auto 1000000000Up 0100000000Down0010000000Left 0001000000Right 0000100000Auxiliary 0000010000CHARPTER 10Equipment Installation1. Fix the decoder firmly on a suitable place2. Set correct address coding according to