Q5001-2007出口欧洲用铝及铝合金板带材.doc

Q/SWA50012007Q/SWA西南铝业(集团)有限责任公司企业标准Q/SWA50012007（修改采用EN485 ）出口欧洲用铝及铝合金板、带材2007-09-28实施2007-09-28发布西南铝业(集团)有限责任公司 发布前 言本标准在欧共体EN485铝及铝合金板、带材的基础上起草，其主要技术指标等同EN485。本标准的力学性能完全等同EN485铝及铝合金板、带材标准。本标准的尺寸偏差等同EN485铝及铝合金板、带材标准。本标准中的试验方法引用我国国家标准。按欧共体EN485标准订货的板、带材，可按本标准组织生产、检验和验收。本标准由西南铝业（集团）有限责任公司负责起草。本标准水平等同EN485铝及铝合金板、带材。本标准的附录A、附录B为规范性附录。本标准主要起草人：张 钰 李 瑞 山本标准审核（会签）人：王 正 安本标准批准人：尹 晓 辉III出口欧洲用铝及铝合金板、带材1 范围本标准规定了出口欧洲用铝及铝合金板、带材的要求、试验方法、检验规则、标志、包装、运输、贮存等。本标准适用于采用欧共体EN485标准或相当欧共体EN485标准订货的铝及铝合金板、带材产品。2 规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注年代的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本标准。然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注年代的引用文件，其最新版本适用于本标准。GB/T 228 金属材料 室温拉伸试验方法GB/T 231 金属布氏硬度试验方法 GB/T 3190 变形铝及铝合金化学成分 GB/T 3199 铝及铝合金加工产品包装、标志、运输、贮存 GB/T 3246.1 变形铝及铝合金制品显微组织检验方法GB/T 3246.2 变形铝及铝合金制品低倍组织检验方法 GB/T 6519 变形铝合金产品超声波检验方法GB/T 6987（所有部分） 铝及铝合金化学分析方法GB/T 20975（所有部分） 铝及铝合金化学分析方法GB/T 7999 铝及铝合金光电(测光法)发射光谱分析方法GB/T 12966 铝合金电导率涡流测试方法 GB/T 16865 变形铝、镁及其合金加工制品拉伸试验用试样GB/T 17432 变形铝及铝合金化学成分分析取样方法GB/T3880（所有部分） 一般工业用铝及铝合金板、带材 3 要求3.1 产品分类3.1.1 铝及铝合金划分为A、B两类，如表1所示。表1牌号系列铝或铝合金类别AB1XXX所有2XXX所有3XXXMn的最大规定值不大于1.8%，Mg的最大规定值不大于1.8%，Mn的最大规定值与Mg的最大规定值之和不大于2.3%。A类外的其他合金4XXXSi的最大规定值不大于2%。A类外的其他合金5XXXMg的最大规定值不大于1.8%，Mn的最大规定值不大于1.8%，Mg的最大规定值与Mn的最大规定值之和不大于2.3%。A类外的其他合金6XXX所有7XXX不可热处理强化的合金可热处理强化的合金8XXX不可热处理强化的合金可热处理强化的合金3.1.2 板、带材的牌号、相应的铝或铝合金类别、状态及厚度规格应符合表2规定。与厚度对应的宽度和长度应符合表3规定。表2牌号类别状态板材厚度规格/mm带材厚度规格a/mm1080AAl99.8(A)AF2.525.02.58.0H1126.025.0O、H111、H12、H14、H22、H240.212.50.26.0H16、H260.24.00.24.0H180.23.00.23.01070AAl99.7AF2.525.02.58.0H1126.025.0O、H1110.225.00.26.0H12、H14、H22、H240.212.50.26.0H16、H260.24.00.24.0H180.23.00.23.01050AAl99.5AF2.5150.02.58.0H1126.080.00、H1110.280.00.26.0H120.240.00.26.0H22、H240.212.50.26.0H140.225.00.26.0H16、H260.24.00.24.0H18、H28、H190.23.00.23.01200Al99.0AF2.5150.02.58.0H1126.080.0O、H1110.280.00.26.0H120.240.00.26.0H22、H240.212.50.26.0H140.225.00.26.0H16、H260.24.00.24.0H18、H190.23.00.23.02014AlCu4SiMgBO0.425.0T30.46.0T4、T4510.4100.0T6、T6510.4100.02014AAlCu4SiMg(A)BO0.26.0T4、T4510.280.0T6、T6510.2100.02017AAlCu4MgSi(A)BO0.425.0T4、T4510.4100.02024AlCu4Mg1BO0.425.0T40.46.0T3、T3510.4100.0T8、T8510.440.03003AlMn1CuAF2.580.02.58.0H1126.080.0O、H1110.250.00.26.0H120.240.00.26.0H22、H14、H240.225.00.26.0H16、H260.24.00.24.0H18、H28、H190.23.00.23.0表2（续）牌号类别状态板材厚度规格/mm带材厚度规格a/mm3103AlMn1AF2.580.02.58.0H1126.080.0O、H1110.250.00.26.0H120.240.00.26.0H22、H240.212.50.26.0H140.225.00.26.0H160.28.00.26.0H26、0.24.00.24.0H18、H28、H190.23.00.23.03004AlMnMg1AF2.580.02.58.0O、H1110.250.00.26.0H12、H22、H32、H14、0.26.00.26.0H160.24.00.24.0H18、H24、H34、H26、H360.23.00.23.0H28、H38、H190.21.50.21.53005AlMn1Mg0.5AF2.580.02.58.0O、H1110.26.00.26.0H12、H22、H14、0.26.00.26.0H160.24.00.24.0H18、H24、H26、H280.23.00.23.0H190.21.50.21.53105AlMn0.5Mg0.5AF2.580.02.58.0O、H111、H12、H22、H14、H24、H16、H26、H18、0.23.00.23.0H28、H190.21.50.21.54006AlSi1FeAF2.56.02.56.0O0.26.00.26.0H12、H14、0.23.00.23.0T40.26.00.26.04007AlSi1.5MnAF2.56.02.56.0O、H1110.212.50.26.0H120.23.00.23.04015AlSi2MnBO、H1110.23.00.23.0H12、H14、H16、H180.23.00.23.0H18、H38、H19、H390.20.50.20.55005AlMg1(B)5005AAlMg1(C)AF2.580.02.58.0O、H1110.250.00.26.0H12、H22、H32、H14、H24、H340.212.50.26.0H16、H26、H360.24.00.24.0H18、H19、H28、H380.23.00.23.05040AlMg1.5MnBH24、H340.81.8H26、H361.02.05049AlMg2Mn0.8BF2.5100.0H1126.080.0O、H1110.2100.0H12、H22、H320.240.0H14、H24、H340.225.0H16、H26、H360.26.0H18、H28、H380.23.05449AlMg2Mn0.8（B）BO、H111、H22、H24、H26、H280.53.0表2（续）牌号类别状态板材厚度规格/mm带材厚度规格a/mm5050AlMg1.5（C）AF2.580.0H1126.080.0O、H1110.250.0H12、H18、H28、H380.23.0H14、H22、H32、H24、H34、0.26.0H16、H26、H360.24.05251AlMg2BF2.580.0O、H1110.250.0H12、H22、H320.225.0H14、H24、H340.212.5H16、H26、H360.24.0H18、H28、H380.23.05052AlMg2.5BF2.580.0H1126.080.0O、H1110.280.0H12、H22、H320.240.0H14、H24、H340.225.0H16、H26、H360.26.0H18、H28、H380.23.05154AAlMg3.5(A)BF2.580.0H1126.080.0OH1110.250.0H12、H22、H320.240.0H14、H24、H340.225.0H26、H360.26.0H18、H28、H380.23.0H190.21.55454AlMg3MnBF2.5150.0H1126.0100.0O、H1110.280.0H12、H22、H320.240.0H14、H24、H340.225.0H26、H360.26.0H28、H380.23.05754AlMg3BF2.5150.0H1126.080.0O、H1110.2100.0H12、H22、H320.240.0H14、H24、H340.225.0H16、H26、H360.26.0H18、H28、H380.23.05182AlMg4.5Mn0.4BF2.580.0O、H1110.23.0H190.21.55083AlMg4.5Mn0.7BF2.5150.0H1126.0100.0O、H1110.2100.00.54.0H116b1.580.0H12、H22、H320.240.0H14、H24、H340.225.0H16、H26、H360.24.0表2（续）牌号类别状态板材厚度规格/mm带材厚度规格a/mm5383AlMg4.5Mn0.9BH1126.080.0O、H1110.2100.00.54.0H116 b1.580.0H22、H320.240.0H24、H340.225.05086AlMg4BF2.5150.0H1126.080.0O、H1110.2100.00.54.0H116 b1.550.0H12、H22、H320.240.0H14、H24、H340.225.0H16、H26、H360.24.0H180.23.06016AlSi1.2Mg0.4BT4、T60.43.06061AlMg1SiCuBO0.425.00.46.0T4、T4510.480.0T6、T6510.4100.06082AlSiMgMnBO0.425.0T4、T4510.480.0T6、T6510.4100.0T61 b、T6151 b0.4100.07020AlZn4.5Mg1BO、T4、T4510.412.5T6、T6510.4100.07021AlZn5.5Mg1.5BT61.56.07022AlZn5Mg3CuBT6、T6513.0100.07075AlZn5.5MgCuBO0.475.0T6、T6510.4100.0T76、T76511.512.5T73、T73511.5100.08011AAlFeSi(A)AF2.580.0O、H111、H14、H240.212.50.23.0H16、H260.24.0H18、H22、0.23.0a 无带材规格的合金订购带材时，应双方协商。b 订购H116、T61、T6151这些状态的产品时，应双方协商。表3 单位为毫米板、带材厚度板材的宽度和长度规格带材的宽度和内径规格a板材的宽度板材的长度带材的宽度带材内径带材外径0.200.505001660100040001660405、505、500、510、605、610、75019200.500.80500200010001000020000.801.20500220010001000022001.208.00500240010001000024001.20150.005002400100010000a 需要其他规格的卷径或带材是否带套筒及套筒材质，由供需双方商定后在合同中注明。3.1.3 标记示例产品标志按产品名称、合金牌号、供应状态、规格及标准编号的顺序表示。标记示例如下：示例1：用3003合金制造的、供应状态为H22、厚度为2.0 mm，宽度为1200mm，长度为2000mm的板材，标记为：板 3003-H22 2.012002000 Q/SWA50012007示例2：用5052合金制造的、供应状态为0、厚度为1.0 mm，宽度为1050mm、内径为610mm的带材，标记为：带 5052-O 1.01050610 Q/SWA500120073.2 化学成分1080A、4006、4007、4015、5005A、5040、5049、5449、5383、6016、7021、8011A合金的化学成分应符合表4规定，其他牌号的产品化学成分应符合GB/T 3190的规定。表4牌号质量分数/%SiFeCuMnMgCrNiZnTi其他杂质aAl b单个合计1080A0.150.150.030.020.02-0.06Ga：0.030.020.0299.8040060.801.200.500.800.100.050.010.20-0.05-0.050.15余量40071.001.700.401.000.200.801.500.200.050.250.150.700.10Co：0.050.100.050.15余量40151.402.200.700.200.601.200.100.50-0.20-0.050.15余量5005A0.300.450.050.150.701.100.10-0.20-0.050.15余量50400.300.700.250.901.401.001.500.100.30-0.25-0.050.15余量50490.400.500.100.501.101.602.500.30-0.20-0.100.050.15余量54490.400.700.300.601.101.602.600.30-0.30-0.100.050.15余量53830.250.250.200.701.004.005.200.25-0.40Zr：0.200.150.050.15余量60161.001.500.500.200.200.250.600.10-0.20-0.150.050.15余量70210.250.400.250.101.201.800.05-5.006.00Zr：0.080.180.100.050.15余量8011A0.400.800.501.000.100.100.100.10-0.10-0.050.050.15余量a 其他杂质指表中未列出或未规定数值的金属元素。b 铝的质量分数为100与等于或大于0.010的所有金属元素总和的差值，求和前各元素数值要表示到0.0X%。3.3 力学性能产品的室温拉伸力学性能应符合表5的规定。表5牌号状态厚度/mm抗拉强度Rm/MPa规定非比例延伸强度Rp0.2/MPa断后伸长率/%弯曲半径a硬度/HBWaA50mmA5.6518090不 小 于1080AAl99.8（A）Fa2.525.060O、H1110.20.5609015260t0t180.51.5609015280t0t181.53.0609015310t0t183.06.0609015350.5t0.5t186.012.5609015350.5t0.5t18H1126.012.5702012.525.07020H120.20.5801205550.5t0t260.51.5801205560.5t0t261.53.0801205570.5t0.5t263.06.0801205591.0t266.012.58012055122.0t26H140.20.51001407040.5t0t320.51.51001407040.5t0.5t321.53.01001407051.0t1.0t323.06.01001407061.5t326.012.51001407072.5t32H160.20.51101509021.0t0.5t360.51.51101509021.0t1.0t361.54.01101509031.0t1.0t36H180.20.512510521.0t400.51.512510522.0t401.53.012510522.5t40H220.20.5801205080.5t0t260.51.5801205090.5t0t261.53.08012050110.5t0.5t263.06.08012050131.0t266.012.58012050152.0t26H240.20.51001406050.5t0t310.51.51001406060.5t0.5t311.53.01001406071.0t1.0t313.06.01001406091.5t316.012.510014060112.5t31H260.20.51101508030.5t350.51.51101508031.0t351.54.01101508041.0t35 表5（续）牌号状态厚度/mm抗拉强度Rm/MPa规定非比例延伸强度Rp0.2/MPa断后伸长率/%弯曲半径a硬度/HBWaA50mmA5.6518090不 小 于1070AAl99.7Fa2.525.060O、H1110.20.5609015230t0t180.51.5609015250t0t181.53.0609015290t0t183.06.0609015320.5t0.5t186.012.5609015350.5t0.5t1812.525.06090153218H1126.012.570202012.525.07020H120.20.5801205550.5t0t260.51.5801205560.5t0t261.53.0801205570.5t0.5t263.06.0801205591.0t266.012.58012055122.0t26H140.20.51001407040.5t0t320.51.51001407040.5t0.5t321.53.01001407051.0t1.0t323.06.01001407061.5t326.012.51001407072.5t32H160.20.51101509021.0t0.5t360.51.51101509021.0t1.0t361.54.01101509031.0t1.0t36H180.20.512510521.0t400.51.512510522.0t401.53.012510522.5t40H220.20.5801205070.5t0t260.51.5801205080.5t0t261.53.08012050100.5t0.5t263.06.08012050121.0t266.012.58012050152.0t26H240.20.51001406050.5t0t310.51.51001406060.5t0.5t311.53.01001406071.0t1.0t313.06.01001406091.5t316.012.510014060112.5t31H260.20.51101508030.5t350.51.51101508031.0t351.54.01101508041.0t35表5（续）牌号状态厚度/mm抗拉强度Rm/MPa规定非比例延伸强度Rp0.2/MPa断后伸长率/%弯曲半径a硬度/HBWaA50mmA5.6518090不 小 于1050AAl99.5Fa2.5150.065O、H1110.20.5659520200t0t200.51.5659520220t0t201.53.0659520260t0t203.06.0659520290.5t0.5t206.012.5659520351.0t1.0t2012.580.06595203220H1126.012.57530202312.580.070252022H120.20.5851256520.5t0t280.51.5851256540.5t0t281.53.0851256550.5t0.5t283.06.0851256571.0t1.0t286.012.5851256592.0t2812.540.08512565928H140.20.51051458521.0t0t340.51.51051458521.0t0.5t341.53.01051458541.0t1.0t343.06.01051458551.5t346.012.51051458562.5t3412.525.010514585634H160.20.512016010010.5t390.51.512016010021.0t391.54.012016010031.5t39H180.20.514012011.0t420.51.514012022.0t421.53.014012023.0t42H190.20.51501301450.51.51501301451.53.0150130145H22 0.20.5851255540.5t0t270.51.5851255550.5t0t271.53.0851255560.5t0.5t273.06.08512555111.0t1.0t276.012.58512555122.0t27H240.20.51051457531.0t0t330.51.51051457541.0t0.5t331.53.01051457551.0t1.0t333.06.01051457581.5t1.5t336.012.51051457582.5t33H260.20.51201609020.5t380.51.51201609031.0t381.54.01201609041.5t38H280.20.514011021.0t410.51.514011022.0t411.53.014011033.0t41表5（续）牌号状态厚度/mm抗拉强度Rm/MPa规定非比例延伸强度Rp0.2/MPa断后伸长率/%弯曲半径a硬度/HBWaA50mmA5.6518090不 小 于1200Al99.0Fa2.5150.075O、H1110.20.57510525190t0t230.51.57510525210t0t231.53.07510525240t0t233.06.07510525280.5t0.5t236.012.57510525331.0t1.0t2312.580.075105253023H1126.012.58535162612.580.080301624H120.20.5951357520.5t0t310.51.5951357540.5t0t311.53.0951357550.5t0.5t313.06.0951357561.0t1.0t316.012.5951357582.0t3112.540.09513575831H140.20.51151559521.0t0t370.51.51151559531.0t0.5t371.53.01151559541.0t1.0t373.06.01151559551.5t1.5t376.012.51151559062.5t3712.525.011515590637H160.20.513017011510.5t420.51.513017011521.0t421.54.013017011531.5t42H180.20.515013011.0t450.51.515013022.0t451.53.015013023.0t45H190.20.51601401480.51.51601401481.53.0160140148H220.20.5951356540.5t0t300.51.5951356550.5t0t301.53.0951356560.5t0.5t303.06.09513565101.0t1.0t306.012.59513565102.0t30H240.20.51151559031.0t0t370.51.51151559041.0t0.5t371.53.01151559051.0t1.0t373.06.01151559071.5t376.012.51151559092.5t36H260.20.513017010520.5t410.51.513017010531.0t411.54.013017010541.5t41表5（续）牌号状态厚度/mm抗拉强度Rm/MPa规定非比例延伸强度Rp0.2/MPa断后伸长率/%弯曲半径a硬度/HBWaA50mmA5.6518090不 小 于2014AlCu4SiMgO0.41.5220140120.5t0t551.53.0220140131.0t1.0t553.06.0220140161.5t556.09.0220140162.5t559.012.5220140164.0t5512.525.0220-1055T30.41.5395245141111.56.040024514-112T4T4510.41.5395240143.0tb3.0tb1101.56.0395240