英文说明书-圣上照明.doc

Dongguan Xianglong Energy Technology Co., Ltd Sensun Lighting Integrated Single High Power LED Street Light Instruction Manual Xl10-SL100w2k178wXl10-SL100w2k178wInstruction manualThe information contained in this manual is the property of Dongguan Fly Dragon Energy Technology Co., Ltd and may not be changed, copied or distributed either in part or in whole without the permission of Dongguan Fly Dragon Energy Technology Co., Ltd .The information contained in this manual is subject to change without a prior notice.SenSun Lighting is registered trademarks of Dongguan Fly Dragon Energy Technology Co., LtdDongguan Xianglong Energy Technology Co., LtdAddress: The second industrial area in Huangang Village, Houjie Town, Dongguan City, Guangdong Province, China.Tel: 0086-769-38872988 0086-769-8558 8479 Fax: 0086-769-8558 0759E-mail: Web: Utilization of used lamps: LED lamps must be disposed of in accordance with current regulations concerning environmental protection. Used lamps should be returned to the applicable collection point, where they will be accepted free of charge. Proper utilization of equipment enables preserving valuable environmental resources and avoiding adverse impacts on health and the environment, which may be threatened by inappropriate waste handling.Legal notice:Although we do our best to calculate SenSun street lamp operating parameters properly, Dongguan Fly Dragon Energy Technology Co., Ltd takes no responsibility for SenSun street lamp operating parameters accuracy. Dongguan Fly Dragon Energy Technology Co., Ltd stipulates that the SenSun stree lamp operating parameters is no subject to claims. If irregularities are detected, please contact us.Contents1.Introduction.42.Technical data.52.1. Basic technical parameters of CLEVEO lamp.52.2. CLEVEO lamp drawing.62.3. Characteristics of the CLEVEO lamp.72.4. Special features of CLEVEO lamps .72.5. LED light sources lifetime.82.6. Light characteristics of CLEVEO lamp.93. Available accessories.103.1. External LED Lights Interface.103.2. Signal cable.103.3. Power cable.104. Configuration and control of CLEVEOs operation.114.1. Lamp parameters configured by the user.114.1.1. Luminous Flux.114.1.2. Internal Dim Mode.114.1.3. External Dim.124.1.4. Aging compensation.125. Installation of the lamp.125.1. Safety regulations.125.2. Proceedings with the LED lamp.135.3. Assembly procedures.145.3.1 Installing the power cord.145.3.2. Setting the lamp inclination angle.155.3.3 Installation of the lamp on post.166. Service.171. IntroductionSenSun LED street light is own-patented single Integrated module but with super high power. It is an intelligent and economical lamp with a versatility of applications and very good technical parameters. By combining a unique and patented photometric distribution and heat dissipation technical system, the LED street light fixtures are high luminous efficiency over 80lm/w, also with other much high electronic data. With many patents in this field, we achieved an innovative product with high performance and unique functionality. SenSun lamps are environmentally friendly. They are characterized by low demand for electrical energy and made of safe materials.Advantages of SenSun LED street lights: Tremendous energy saving with high brightness LED light source, saving energy up to 60%-80% than the conventional sodium and mercury lamps ; Simple maintenance for special structure & design with three years warranty from us; Patented heat dissipation technique solving concentrate heat from chips; Automatic on & off function and adjustable brightness; Embedded intelligent driver without flickering; Over 50,000 hours (about 10 year) LED lamp life; Low installation costs without trenches and cables;Applications: illumination of freeways, streets and roads illumination of parking lots, squares, parks, gas stations illumination of pedestrian areas illumination of industrial and residential zones2.Technical data2.1. Basic technical CLEVEO lamp parameters Table 1: Light source parametersLight SourcePower LEDSWhite BalanceCool whiteNatural whiteWarm whiteColor Temperature6500k4500k3500kOutput light flux for Power of 40w*3000lm2400lm2250lmOutput light flux for Power of 65w*4200lm3350lm3150lmOutput light flux for Power of 90w*5500lm4400lm4100lm* Actual output light flux/ Given values consider the losses in the optical system as well as thermal losses of the LED. The LED power can be widely adjusted by the user.Table 2: Basic lamp parametersModelXl10-SL100w2k178wInput VoltageAC170260V/DC53VGrequency Range5060HZPower Factor(PF)0.95Total Harmonic Distortion(THD)88%LED Power Consumption100WConsole Power Consumption110WLED Luminous Efficiency80Lm/WLED Initial Luninous Flux8000LmLumiare Efficiency (%)90%Uniformity of Illuminance0.6Correlated Color Temperature 4000K5500KColor-rendering Index(CRI)Ra75Distribution Curve FluxBat-wing/SquarenessJunction Temperature (Tj)50000 HoursMaterialAluminium alloyNet weight10.8KGPackage Size60L*36W*20H(CM)2.2. SenSun LED Street Lamp Drawing 2.3. Characteristics of the SenSun street light Tremendous Energy Saving: Used the super high power, high brightness LED light source, together with automatic adjustment for illumination, SenSun light can save energy up to 60%-80% than conventional sodium and mercury lamps; Unique Supper High Power: Used self-developed high-grade LED chip and creative patented packaging technique, SenSun LED street lights have super power from 60w to 200w of single chip with high luminous efficiency, high reliability and balance electrical parameters Patented heat dissipation Technology: Aluminium alloy lamp holder combined with radiator can fully solve heat dissipation problems special for heat concentrated caused by integrated luminous crystal and protect LED life. Long Lifespan: Over 50,000 hours working time, which is 5-10 times than traditional sodium or mercury lamp. (Working for 10 hours a day, can be used for over 13 years) Simple Maintenance: Speical structure & design of LED Lights for lowest cost maintenance, three years warranty and five years of maintenance are provided. No Strobe Flashing: Working under DC, eliminate the tireless which caused by the traditional strobe flashing; Environmental Protection: No lead, no mercury, no environmental pollution, less line loss. Power factor 0.95, THD15%. EMI with the global universal index reduce power loss and line loss to avoid contamination of high frequency interference. Impact Resistance: Shock-proof; Ultraviolet (UV) & water proof and Infrared Radiation (IR). The level of protection (lp) is more than 65. No filament and glass frames are to avoid traditional lamp break for harmless to human body. Multiple Color Temperature Options: Color temperature to meet different needs of different occasion could make observers feel more comfortable. SenSun lights have high brightness efficiency up to 100 lm/w, various color temperatures and good CRI(color rendering index). Unique & Elegant Shape: Special appearance design with proprietary optical and heat dissipation technology provide not only unique and elegant shape but also meet the heat dissipation requirements of concentrate heat from chip.SenSun lights are not only pretty but also much functional. 2.5. LED light sources lifetime.Based on temperature measurements of the LEDs and the LED manufacturers data, it is possible to estimate the lifetime of the light sources installed in the Sensun street lamp.Lifetime is referred to the time after which the lamp brightness decreases by 30% compared to the initial brightness (often expressed as life time L70). Estimated life time of particular Sensun street lamp can be read by LED Lights Interface which is available as on option.These estimates are determined assuming the lamp operation at the average annual air temperature equal to 15 degrees Celsius. If the average annual temperature is lower than 15C, expected life time will increase according to the specified value.If the average annual temperature is higher than 15C, expected life time will decrease according to the specified value.Electric power W60100150180200Expected life time L70 hThe above values are determined on the basis of temperature measurement of LEDs junctions and statistics provided by the manufacturer of LEDs, and in the specific conditions of the lighting system they may differ from the above values.These life times do not relate to other elements of the lamp (power supply, controller, cooling system), which may require periodic maintenance or replacement. However, these elements are chosen to go along with the long lifetime of the LEDs.2.6. Light characteristics of CLEVEO lamp5. Installation of the lamp 5.1. Safety regulations1. Installation of the lamps may only be carried out by qualified personnel, with permits appropriate to ones country.2. During the installation of lamp every precaution should be kept adequately to location and method of assembly.3. During the installation of the lamps mains power should be disconnected. Installation of lamps when power is on poses a risk of electric shock or damage of the lamp.4. LED lamp must be connected to a power source with all the guidelines targeting the interests of safety.5. Before connecting, you should always check the electrical connections and their compliance with relevant standards and make sure that the power source is of appropriate electrical parameters.5.2. Proceedings with the LED lamp SenSun street lamp is constructed in a manner which ensures high durability and resistance to external conditions. SenSun street lamp has an IP 65, level of protection against external conditions. This means that the sealed lamp can work in almost any weather conditions and with a large dust rate. To ensure long and reliable operation of the lamps, one should follow instructions on the lamp assembly and service of LED lamps described later in this manual.Handling with the LED lamp1. During the assembly, transportation or any other operations related to the LED lamp, avoid strong shocks, impacts and any other mechanical strokes.2. Do not immerse LED lights in water as well as other liquids.3. Avoid contact of the LED lights with liquids, solvents, penetrating substances or any other substances which could permanently damage or pollute the casing of the lamp or penetrate the inside of the lamp.4. You should avoid opening the LED lamps. LED lamp can be opened only during the installation (if it is necessary to connect the cables) and during the service work. Opening of LED lights and all the work in its interior can be exercised only by properly trained persons.5. It is recommended that the opening of the lamp takes place indoors. If you work outside, the opening of the lamp is possible only on days on which there is no rainfall. Water that gets into the lamps may have an impact on shortening the life of LEDs or their damage. It is recommended to perform installation of LED lights on sunny days.6. Installation and set up the lamp on a high level of humidity (above 60%) days are notrecommended. This may lead to shortening the life of LEDs, and in extreme cases, damaging the LEDs or the electronic circuits inside the lamp.7. Connecting the LED lamps to the electricity grid can be made only with power switched off.8. Shinesun street lamp has a protection switching off power supply in case of the opening of theenclosure. However, it is recommended that the work inside the frame took place when the power is off.5.3. Assembly procedures 5.3.1 Installing the power cord Prepare LED lamp and an insulated star screwdriver with PH1 ending and 22mm wrench. Prepare a section of power cable with appropriate length and parameters: Round cable: 3 x 1.52.5 mm2 (3 x AWG 1316), External cable diameter 1014 mm, Place the lamp on the table or other flat and stable surface. Open the lamp unlocking the latch. Put the cable through the bushing and fixing sleeve leaving inside the lamp approx. 10 cm of cable. The power cord terminals remaining inside the lamp should be fixed to the screw terminal in the following order (from the housing edge): live, PE,neutral. Screw the cable bushing using a 22mm wrench. The bushing should bescrewed strongly enough so that the cable is not loose. Check the correctness of the connection. Close the housing tightly. Locking the latch should require some force and should be ended with a loud click. If closing of the housing requires excessive force, check the positioning of the seal placed along the edge connecting both halves and check if the cable is not squeezed. Visually check the correctness of closing. Both halves should be aligned evenly on the whole circumference of the lamp. Connect the lamp to power supply in order to check if it works correctly.5.3.2. Setting the lamp inclination angle Shinesun street light is equipped with a fixing element with adjustable angle. Thus the light can be installed on posts ended vertically and horizontally. Shinesun lamp in standard enables adjustment of angle in two ranges: -5o to 20o and 70o to 95o. Other adjustment ranges are available on request. Prepare the lamp and a 17 mm wrench. Place the lamp on a table or any other flat and stable surface. Open the lamp unlocking the latch. Using 17mm wrench, loosen the locking screw. For large changes in the angle of the lamp you will need to completely unscrew the screws. Set the mounting sleeve in a given position. On the body casing, next to the screw there is pitch to facilitate the setting specified angle. Screw the locking screw until it stops, so that the blocking pad located underneath comes equally between the pitch teeth. Close the housing tightly. Locking the latch should require some force and should be ended with a loud click. If closing of the housing requires excessive force, check the positioning of the seal placed along the edge connecting both halves and check if the cable is not squeezed. Optically check the correctness of closing. Both halves should be aligned evenly on the whole circumference of the lamp.5.3.3 Installation of the lamp on post Lamp is suited for mounting on pole or arm, which end has a diameter of 60 mm and length at least 120 mm. Prepare an LED lamp and Allen wrench 5 mm. Make sure LED lamp is equipped with cable and set the angle of the lamps in accordance with the instructions contained in sections 5.3.1. and 5.3.2. Lead the power cable inside the post. Slightly remove the lock screws. Mount LED lamp on the end of a column or a boom. Tighten both lock screws. Connect the power supply. Check the correctness on the parameters of power and accuracy of connections. Turn on the power and verify the operation of the lamp.6. Sensun Lamp Main Parts Diagram.1) Predominant Heat-removal Capability According to the conduction, radialization and convection heat-removal design, when the temperature is 35, the LED junction temperature is less than 75.2) Scientific Optical Design Completely fit for the road lighting standard and the reflector technology. The light efficiency rate is more than 95%.3) High Efficiency Power Supply Power supply operate from a 75275 Vac input range. They are designed to be highly efficient and highly reliable. Features include lighting protection, over voltage protection, over current protection, short circuit protection and over temp