岗位讲述 -电工和电气技术员 中英文.doc

电气技术员岗位讲述(模板三：基层技术岗位) 尊敬的各位领导，你们好:欢迎莅临本岗位检查指导工作，我叫XXX，XXXXX（自选项：可简单介绍工作时间和毕业院校），岗位是电气技术员本岗位主要职责是：1、贯彻执行国家和上级的各项技术政策、法令法规、规范和标准。2、制定技术管理工作计划并组织实施，整理归档技术资料。3、按照有关标准的要求，负责产品施工（生产） 全过程的技术管理。4、负责施工图会审，参与技术交底和施工组织设计的编制。5、负责协调解决现场随时出现的技术问题，掌握工程进度信息，对现场工人进行技术指导。本岗位涉及的主要技术标准及规范是： 电气装置安装工程电缆线路施工及验收规范 GB 50168-96 电气装置安装工程低压电气施工及验收规范 GB 50254-96 电气装置安装工程电气设备交接试验标准 GB 50150-06电气装置安装工程旋转电机施工及验收规范 GB 50170-96我的岗位讲述完毕，谢谢。Electrical technician post presentationDear leaders, Welcome to inspect and guide the work of mine, my name is XXX, I am the electrical technician of the Electrical & instrumentation branch company.My basic responsibilities are:1. Carry out the technology policy, rules and regulations, norms and standards of the country and superior.2. Draw up a plan of technology management work and enforce, collating and archiving technology information.3. In accordance with the requirements of the relevant standards, responsible for the technical management of the whole process of construction (production).4. Responsible for construction drawing joint hearing, participate in technical disclosure and the preparation of construction organization design.5. To coordinate and solve technical problems at any time in the site. Grasp the project progress information and Technical guidance to the site workers.The main risk and control measures of this post areRisk: quality riskControl measures: Strict implementation of technical standards in the electrical engineering, control of construction quality, check out the construction equipment timely, strengthen QHSE management work on the construction site, to prevent the emergence of three illegal behaviors.The main technical standards and norms which this position is involved are:1. Electrical equipment installation project cable line construction and acceptance standard GB 50168-96(2) Low voltage electrical equipment installation project construction and acceptance standard GB 50254-96(3) Electrical equipment installation project electrical equipment commissioning test standard GB 50150-06(4) Rotary motor electrical equipment installation project construction and acceptance standard GB 50170-50170Thats all, thank you.电工岗位讲述尊敬的各位领导，你们好：欢迎莅临本岗位检查指导工作，我叫XXX，岗位是电工。本岗位主要职责是：1、严格按照操作规程操作，杜绝违章操作。2、及时制止电气维修中发现的乱接电源现象。3、负责业务范围内的供电线路、照明器具和电气设备的维修、保养，保证设备正常工作。4、定期巡视设备及供电电路运行状况，发现事故苗头和隐患及时排除，防止事故发生。5、按照施工组织设计及文明施工要求，落实安全用电保护工作。本岗位安全操作规程是：工作前应详细检查自己所用工具是否安全可靠，穿戴好必须的防护用品，以防工作时发生意外。电气装置或线路在未经检测前，一律视为“有电”。维修线路时，在开关手把上或线路上悬挂“有人工作、禁止合闸”的警告牌，防止他人中途送电。作业结束后，送电前认真检查并和有关人员联系好，方能送电。工作结束后，对作业现场进行清理，做到工完料净场地清。本岗位主要风险及控制措施是：风险：触电控制措施：正确穿戴和使用合格的安全防护用品，严格遵守作业安全规程和设备机具安全操作规程，坚持作业前安全分析和二人工作制。我的岗位讲述完毕，谢谢！Electrician post presentationDear leaders, Welcome to inspect and guide the work of mine, my name is XXX, I am the electrician of the Electrical & instrumentation branch company.My basic responsibilities are:1In accordance with the rules strictly and operations and put an end to illegal operation.2. Stop the phenomenon which is found that random access power in the electrical maintenance.3. Responsible for business within the power lines, lighting fixtures and electrical equipment repair and maintenance, to ensure that the device is working properly.4. Regularly inspect equipment and power supply circuit operation conditions, promptly eliminate the accident symptom and hidden danger which is found, prevent accidents.5. According to the construction organization design and civilized construction requirements, ensure the implementation of the protection of the safe use of electricity.The safe operating procedures of this position are:1.Before work we should check own tools carefully and make sure theyre reliable, wear necessary protective equipment in case of an accident at work.2.Electrical device or circuit before test shall be regarded as electricity.3.When maintain the lines, hang on a warning sigh which said “someone is at work, please no switching” on the switch hand or a line to prevent someone to delivery of current.4.After the operation, check them carefully and contact related personnel in order to power transmission.5.After the operation, clean up the working site; make sure the material and the work site all clean after work.The main risk and control measures of this post areRisk: electric shockControl measures: Properly wear and use the security products, strict compliance with the