


全文预览已结束
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
颚式破碎机的维修规则和保养颚式破碎机广泛运用于矿山、冶炼、建材、公路、铁路、水利和化工等行业中各种矿石与大块物料的中等粒度破碎。被破碎物料的最高抗压强度为320Mpa。颚式破碎机的维修,无论什么机器维修保养都是很重要的 1. 颚式破碎机润滑 (1) 经常注意并及时做好摩擦面得润滑工作,可确保机器的正常运转和延长其使用寿命。 (2) 颚式破碎机所采用润滑脂应根据使用的地点、气温条件下而定,一般情况下采用钙基、钠基和钙那基润滑脂。 (3) 加入轴承座内的润滑脂为其空间容积的50%左右、每36个月更换一次。换油时应用洁净的汽油或煤油清洗滚柱轴承的滚道。 (4) 颚式破碎机开动前,推力板与推力板支座之间应注入适量的润滑脂。 2. 颚式破碎机维修 为保证颚式破碎机的正常工作,处正确操作外,必须进行计划性维修,其中包括日常维护检查,小修、中修和大修。 (1) 小修 主要内容包括检查并修复调整装置,调整排料口间隙,对磨损的衬板调头或更换。检查传动部分、润滑系统及时跟换润滑油等。小修的周期为13个月左右。 (2) 中修 处进行小修的工作外,还包括更换推力板、衬板、检查并修复轴瓦等。中修的周期一般为12年左右。 (3) 大修 处进行中修的工作外,还包括和更换车削偏心轴和鄂心轴,浇铸连杆头上部的巴氏合金,更换或修复个磨损件。大修的周期一般为5年左右。自公司成立以来,企业以先进的现代化管理体系精工制作,自主创新,汇集了一批科技精英,公司长期与国内外科研单位合作,引进了具有国内外先进技术及工艺,现已形成破碎机、制砂机、碎石机、振动筛、给料机、球磨机、回转窑等系列产品,高技术含量、高可靠性、低使用维护成本,使我们的产品一直处于领先水平,目前已出口到俄罗斯、中东、非洲、东南亚等多个国家。Jaw crusher maintenance rules and maintenanceJaw crusher is widely used in mining, metallurgical industry, building material, highway, railway, water conservancy and chemical industries all kinds of ores and materials of the medium size and broken. Being broken material of the highest compressive strength for 320 Mpa. Jaw crusher maintenance, no matter what the machine maintenance is very important1The jaw crusher lubrication(1) often note and the friction surface to make timely, ensure the machine work lubrication of the normal operation and prolong the service life.(2) the jaw crusher grease according to the place, should be used under the condition of temperature and decide, usually with calcium and sodium, calcium, and the grease.(3) to join in the bearing grease of the volume of space for about 50%, every 3 6 months change again. Change the oil use clean gasoline or kerosene cleaning roller bearing the groove.(4) jaw crusher, thrust board before start with thrust bearing plate should be adequate grease injection of between.2. Jaw crusher maintenanceTo guarantee the normal work of the jaw crusher, place the correct operation, must be planned repair, including maintenance, repair and minor repairs, check the overhaul.(1) minor repairs main content including inspection and repair, adjust the adjustment device discharging mouth gap, to wear the liner switching or replacement. Check the transmission part, lubrication system with in time for lubricating oil etc. Minor repairs the cycle of 1 3 months or so.(2) in the minor repairs to repair the work outside, still including change thrust board, foils, inspection and repair bearings, etc. The cycle of repair is generally from 1 to 2 years or so.(3) overhaul in the work to repair the outside, still include and replace turning partiality axis and hubei heart axis, casting connecting rod head of the department of babbitt, change or repair a wear parts. Overhaul cycles are usually for 5 years.Shanghai Esong mining machinery Co., LTD. Wilson, since the company was founded, enterprises with advanced modern management system seiko produced, the independent innovation, collected a batch of technology elite, the company long-term and the domestic and foreign research unit cooperation, has introduced the domestic and international advanced technology and process, has been formed crusher, the sand machine, hammer, vibrating screen, feeding machine, the ball mill, the rotary kiln, etc. Series of products, high technology content, high reliabil
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
评论
0/150
提交评论