铝电解规格书.doc

Aluminum Electrolytic Capacitors CS SERIES 1. ScopeThis specification covers “CS Series” V-chip aluminum electrolytic capacitors.2. Reference StandardJapanese industrial Standard JIS C-5141 characteristics W and JIS C-5102 except as specified in this specification.3. Environmental Protection StandardComply with the EU directive 2002/95/EC.4. Operating Temperature Range-40C +85C5. Voltage Range4 100V6. Capacitance Range0.1 1500mF7. Capacitance Tolerance20% at 120Hz, 20C8. Leakage Current1 0.01 CV or 3 (mA) whichever is greater (after 2 minutes)9. Tan dMeasurement frequency: 120Hz, Temperature: 20CRated Voltage (V)46.3101625355063100Tan d (max.)0.500.300.240.200.160.140.140.120.1210. Stability at Low TemperatureMeasurement frequency: 120HzRated Voltage (V)46.3101625355063100Impedance RatioZT/Z20 (max.)Z-25C /Z+20C743222222Z-40C /Z+20C158644333311. Load Life After 2000 hours application of rated voltage at 85C, capacitors meet the characteristics requirements listed.Capacitance ChangeWithin 20% of initial value(Within 25% of initial value for 4V)Tan d200% or less of initial specified valueLeakage CurrentInitial specified value or lessAluminum Electrolytic Capacitors CS SERIES 12. Shelf LifeAfter leaving capacitors under no load at 85C for 1000 hours, they meet the specified value for load life characteristics listed above.13. Resistance to Soldering HeatAfter reflow soldering according to Reflow Soldering Condition (see page 5) and restored at room temperature, they meet the characteristics listed.Capacitance ChangeWithin 10% of initial valueTan dInitial specified value or lessLeakage CurrentInitial specified value or less14. MarkingCapacitors shall be legibly marked with the following:1) Manufactures mark2) Rated voltage and nominal capacitance (6.3 voltage shall be marked with 6 voltage)3) Negative polarity4) Marking: BlackcsSeriesCapacitanceRated Voltage15. Drawing (Unit: mm)(46.3) (8, 10)Aluminum Electrolytic Capacitors CS SERIES 16. Dimensions (Unit: mm)DL45.455.46.35.46.37.7810.51010.512.513.512.5161616.5A1.82.12.42.42.93.24.74.75.5B4.35.36.66.68.310.313.013.017.0C4.35.36.66.68.310.313.013.017.0E1.01.32.22.23.14.54.44.46.7L5.45.45.47.710.510.513.516.016.517. Taping SpecificationsApplicable standard JIS C0806(CS, CK, SC, CN, KP, LZ, KZ, FZ, EL, KL, KH, HU series)Carrier Tape17.1. Drawing 1 (for 4 10) DimensionSeriesCS, CK, SC, CN, KP, LZ, KZFZ, EL, KL, KHCS, CK, CN, LZ, KZ, FZ, EL, KL, KHDL45.455.46.35.445.855.865.86.37.7810.51010.5W12.012.016.012.012.016.016.024.024.0P8.012.012.08.012.012.012.016.016.0F5.55.57.55.55.57.57.511.511.5A5.06.07.05.06.07.07.08.710.7B5.06.07.05.06.07.07.08.710.7T25.85.85.86.36.36.38.411.011.017.2. Drawing 2 (for 12.5 16)Dimension (Unit: mm)DL12.513.512.516W0.332.032.0P0.124.024.0F0.114.214.2A00.214.014.0B00.214.014.0T20.214.016.5S0.128.428.4Aluminum Electrolytic Capacitors CS SERIES 17.3. ReelPackage quantityDLQty./Reel45.5/5.82000 pcs.5, 6.35.4/5.81000 pcs.6.37.71000 pcs.8, 1010.5500 pcs.12.513.5200 pcs.12.516150 pcs. D456.38, 1012.5A1414182634 18. Lead-free Reflow Soldering Condition A. Recommended Conditions for Reflow Soldering(1) A thermal condition system such as infrared radiation (IR) or hot blast should be adopted, and vapor heat transfer systems (VPS) are not recommended.(2) Reflow soldering should be performed one time. If the capacitor has to be reflowed twice, 30 minutes must be layout between each time.(3) For lead-free type reflow soldering, please observe proper conditions below:a) The time of preheating from 150C to 200C shall be within maximum 180 seconds;b) The time of soldering temperature at 217C measured on capacitors top shall not exceed tL (second);c) The peak temperature on capacitors top shall not exceed Tp(C), and the time within 5C of actual peak temperature shall not exceed tp (second).B. Classification Reflow ProfileTp Ramp-up *1tpCritical Zone217C to Tp217200tL150Preheat 180 sec Max.Ramp-down *225 25C to Peak *3Time (sec.) 時間（秒）Temperature 温度 (C)*1. Average ramp-up rate is 3/second max.*2. Ramp-down rate is 6/second max.*3 .Time from 25 to peak temperature is 8 minutes max. Aluminum Electrolytic Capacitors CS SERIES C. Allowable Range of Peak TemperatureSize Thickness (mm)Tp(C)tL (second)tp (second)46.32.525009040810.5L2.5240090301010.5L2.52350603012.5/162.5230030 (20*)20Re: (20*) is special for mid-to-high voltage which is HU series.D. Recommended Land Size (Unit: mm)SizeXYa41.62.61.051.63.01.46.31.63.52.1810.5L2.53.53.01010.5L2.54.04.012.513.5/163.05.74.01616.5/21.53.56.56.0YYaX19. The Raw Materials of Lead WireNameMaterialPercentageTPCSFe71.35%Cu20%Sn8.65%20. Explanation of Part Number1 2 3 4 5 6 7 8 9 10 11 12 13 14SeriesVoltage (WV)Capacitance (mF)Cap. Tol. (%)Type_LeadProcessDia. ()Length (mm)Example: CS 1C 221 M - C R E 77Length (7.7mm)Case Diameter (6.3mm)Lead Process (Taping & Reel)Type (Chip)DashCapacitance Tolerance (20%)Capacitance (220mF)Voltage (16V)Series (CS)Aluminum Electrolytic Capacitors CS SERIES 21. ConstructionElectrolytic paperBase plateAluminum caseAluminum foil (Anode & cathode foil)Rubber sealLead wireElectrolyte22. Frequency Coefficient of Allowable Ripple CurrenFrequency50Hz120Hz300Hz1kHz10kHzCoefficient0.701.001.171.361.5023 Dimensions & Maximum Permissible Ripple CurrentWVmF46.3101625SIZER.C.SIZER.C.SIZER.C.SIZER.C.SIZER.C.4.74x5.4174x5.419104x5.4254x5.4205x5.428154x5.4285x5.434224x5.4314x5.4284x5.4285x5.4355x5.4355x5.4396.3x5.452334x5.4265x5.4395x5.4435x5.4406.3x5.4634X5.4314X5.4326.3x5.4575X5.442474x5.4344x5.4366.3x5.4595x5.4446.3x5.4685x5.4475X5.4436.3x5.468564x5.4395x5.4466.3x5.4576.3x5.4746.3x5.482685x5.4456.3x5.4626.3x5.4726.3x5.4806.3x5.4945X5.4521005x5.4615x5.4556.3x5.4766.3x5.4866.3x7.71306.3x5.4718X6.22008X6.2911506.3x5.4746.3x5.4786.3x5.4886.3x7.71358x10.52006.3X7.71302206.3x5.4826.3x5.4956.3x7.71506.3x7.71508x10.52508X6.22508X6.21358X10.52153306.3x7.71506.3x7.71508x10.52808x10.52808x10.53108X6.230010x10.53404706.3x7.71508x10.53008x10.53008x10.533010x10.54006.3X7.715010X10.532010X10.54206808x10.53008x10.530010x10.538010x10.545010X13.555010008x10.53308X10.533010x10.545010x10.549012.5X13.582010X10.543010X13.555012.5X13.5710150010x10.545010X10.545010X13.565012.5X13.575012.5X16100010X13.5650Aluminum Electrolytic Capacitors CS SERIES WVmF46.3101625SIZER.C.SIZER.C.SIZER.C.SIZER.C.SIZER.C.220010X13.562012.5X13.589012.5X13.596016X16.5115016X16.5125010X10.548010X13.572012.5X161000333010X13.570012.5X16100016X16.5130016X16.5135012.5X13.590012.5X161050470012.5X13.585016X16.5140016X16.51450680016X16.5135012.5X16900 WV mF355063100SIZER.C.SIZER.C.SIZER.C.SIZER.C.0.14x5.41.04x5.41.00.224x5.42.34x5.42.30.334x5.43.54x5.43.50.474x5.45.04x5.45.014x5.4104x5.4104x5.4101.54x5.4124x5.4126.3x5.4152.24x5.4154x5.4156.3x5.4203.34x5.4184x5.4185x5.4206.3x5.4286.3X7.7458X6.2504.74x5.4204x5.4195x5.4236.3x5.4305x5.4236.3X7.7506.3X5.4308X6.250105x5.4305x5.4276.3x5.4346.3x7.7506.3x5.4348X6.2504X5.4206.3X7.7558X10.5110226.3x5.4546.3x5.4606.3x7.7708x10.51208X6.21208X6.23510X10.51808X10.5140336.3x5.4606.3x7.7856.3x7.78510x10.51908X6.21308X6.2658X10.5160476.3x5.4706.3x7.7908x10.51708X6.21658X10.511010X10.523010X10.5130566.3x7.7806.3x7.71108x10.5250686.3x7.71108x10.517010x10.52601006.3x7.71208x10.520010x10.528012.5X13.54408x10.517510X13.529010X10.524012.5X13.53801508x10.522010x10.524010X13.531022010x10.531010x10.532010X13.533016X16.57008X10.527010X13.540012.5X13.558033010x10.535012.5X13.560016X16.582010X13.542012.5X1672047012.5X13.560016X16.585016X16.595010X13.553012.5X1674010X10.540068012.5X13.575016X16.595010X13.5560100016X16.5110012.5X16800Aluminum Electrolytic Capacitors CS SERIES Allowable ripple current (mA rms) at 85 120Hz24. General Information for ApplicationThe following precautions must be observed when using electrolytic capacitors.A) Circuit Design1) Please make sure that the environmental and mounting conditions to which the capacitor to be exposed are within the conditions specified in this catalogue.2) Operating temperature and applied ripple must be within the specifications.3) Appropriate capacitors, which comply with the life requirement of the products, should be selected when designing the circuit.4) Aluminum electrolytic capacitors are polarized. Do not apply reserve voltage or AC voltage. Please use non-polarized capacitors for a circuit that can possibly see reserved polarity.Note: Non-polarizes capacitors cannot be used for AC voltage application.5) Do not use aluminum electrolytic capacitors in a circuit that requires rapid and very frequent charge or discharge. In this type of circuit, it is necessary to use special design capacitors with extended life characteristics.6) Do not apply excess voltage.j Pleased pay attention so that the peak voltage, which is DC voltage overlapped by ripple current, should not exceed the rated voltage.k In the case where more than two aluminum electrolytic capacitors are used in series, please make sure that applied voltage should be lower than rated voltage should be applied to each capacitor equally using a balancing resistor in parallel with the capacitor.7) Outer sleeved of the capacitor is not guarantee as an electrical insulator. Do not use standard sleeve on a capacitor in applications that require electrical insulation. When the application requires special insulation, please contact our sales office for details.8) Capacitors must not be used under following conditions:j (a) Capacitors must not be exposed to water (including condensation), brine or oil.(b) Ambient conditions that include toxic gases such as hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonium, etc.(c) Ambient conditions that expose the capacitor to ozone, ultraviolet ray and radiation. k Severe vibration and physical shock conditions that exceed our specification. Vibration test condition: Vibration frequency range: 105510Hz Sweep rate : 105510Hz per minute Sweep method : logarithmic Amplitude or acceleration: 1.5 (max. acceleration is 10G) Direction of vibration : X, Y, Z direction Testing time : 2 hours per each directionAluminum Electrolytic Capacitors CS SERIES Shock is not applicable normally. If a particular condition is required, please contact our sales office.9) When designing a circuit board, please pay attention to the following:j Make the pad spacing on the PC board matching with the lead space of the capacitor.k There should not be any circuit pattern or circuit wire above the capacitor safety vent.10) The main chemical solution of the electrolyte and the separator paper in the capacitor are combustible. The electrolyte is conductive. When it comes in contact with the PC board, there is a possibility of pattern or short circuit between the circuit pattern, which could result in smoking or fire. Do not locate any circuit pattern beneath the capacitor end seal.11) Do not design a circuit board so that heat generating components are placed near an aluminum electrolytic capacitor or reserve side of PC board (under the capacitor).12) Please refer to the pad size layout recommendations in our catalogue when designing in surface mount capacitors.13) Electrical characteristics may vary depending on changes in temperature and frequency. Please consider the variation when you design circuits.14) When you install more than 2 capacitors in parallel, consider the balance of current following in to the capacitor.B) Mounting1) Once a capacitor has been assembled in the set and power applied, do not attempt to re-use the capacitor in other circuits or application.2) Electric potential between positive and negative terminal may exist as a result of returned electromotive force, so please discharge the capacitor using 1KW resistor.3) Leakage current of the parts that have stored for long period may increase. When leakage current has increased, please perform a voltage treatment using a 1KW resistor.4) Please confirm rating and polarity before installing capacitor on the PC board.5) Be careful not to deform the capacitor during installation.6) Please confirm that the lead spacing of the capacitor matches the pad spacing of the PC board prior to installation.7) Please pay attention to the mechanical shock to the capacitor by suction nozzle of the automatic insertion machine or automatic mounted, or by product checker, or by centering mechanism.8) Reflow soldering: please see “Lead free Reflow Soldering Condition”.9) Do not tilt, lay down or twist the capacitor body after the capacitors are soldered to the PC board.10) Do not carry the PC board by grasping the soldered capacitor.11) Please do not allow anytime to touch the capacitor after soldering. If PC board are stored in stack, please make sure PC board or the other components do not touch the capacitor. The capacitor shall not be effected by any radiated heat from the soldered PC board or other components after soldering.Aluminum Electrolytic Capacitors CS SERIES 12) Cleaningj Do not clean capacitors with halogenated cleaning agent. However, if it is necessary to clean with halogenated cleaning agent, please contact our sales office. k Recommended cleaning method: Applicable : Any type, any ratings Cleaning agents : Pine Alpha ST-100S, cleaning through 750H/750L/710M, Sanelek B-12, Aqua Cleaner 210SEP, Techno Care FRW1417, Isopropyl Alcohol. Cleaning condition: Total cleaning time shall be within 5 minutes by immersion, ultrasonic or other method. Temperature of the cleaning agent shall be 60C or lower. After cleaning, capacitors should be dried using hot air for minimum of 10 minutes along with the PC board. Hot air temperature should be below the maximum operating temperature of the capacitor. Insufficient dry after water rinse may cause appearance problems, sleeve shirk, bottom- plate bulge and such. Avoid using ozone destructive substance for cleaning agents to concern about global environment. Please consult us regarding other cleaning agents or cleaning methods.C) In The Equipment1) Do not directly touch terminal by hand.2) Do not short between terminal by conductor, nor spill conductible liquid such as alkaline or acidic solution on or near the capacitor.3) Please make sure that the ambient conditions where the set is installed will be free from spilling water or oil, direct sunlight, ultraviolet rays, radiation, poisonous gases, vibration or mechanical shock.D) Maintenance and InspectionPlease periodically inspect the aluminum capacitors that are installed in industrial equipment. The following Items should be checked:Appearance: Remarkable abnormality such as vent operation, leaking electrolyte etc.Electrical characteristic: Ca