深圳市德普特光电显示技术有限公司.doc

Shen Zhen DPT-TOUCH Co.,LtdDIGITAL TOUCH PANEL PRODUCT SPECIFICATIONCustomer : Customer No : Part No: Issue date: Design: Tan ling ling Approve : Customer Accept: Approve: Accept Date: Add: 4th Floor, 5th building JinMeiwei lst industrial park Xinye West Road HeYi village Shajing Town.Baoan Tel: 86-755-33807200 33807202Fax: 86-755-33807205Email:Http:/ Shen Zhen DPT-TOUCH Co.,LtdRevision sheetRevision No.ReworkNo.Date Revision ReasonSig.Remark：Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationIndex1Index 012Apply to specification 023Dimension appendix4Optical Performance 035Electrical performance036Trust test 467Appearance inspection standard 078Precautions in use 08Page :1 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationApply to specification1 Suitability This specification suit analog resistance touch panel, Which used in LCD module.2 Apply to specification 2.1 Surface Hardness：2H 2.2 Optical Clarity：70% 2.3Operation Voltage：DC 35V 2.4On resistance: 5K 2.5 Faceplate Surface：ITO Film 2.6Operation Force：3N 2.7Operating environment： 0 +50 %90 RH2.8Storage environment：-20 +70 %90 RH 2.9Message Noise：10M DC25V 3.Structure; 3.1Up Circuit: ITO Film 3.2 Down Circuit: ITO Glass: 1.1mm 3.3 Tail Type: FPC(Tinning)4.Dimension Size：please reference appendix drawing file Page :2 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationOptical & Electrical 5Optical performance Light transparency should keep above 83% under the visible wave when the wave length is 550 nm.6 Electrical performance：6.1 Connector resistance 10M DC25V6.3 Electrostatics EnduranceNo abnormal appearance after 10KV，100，250PF electrostatic used.6.4 Operation Voltage3V5V DC6.5 Operation Current 5mA。 Page :3 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationReliability test7Relialility test：7.1 High temperature testafter putting panel at 70 for 96 hours, then leaving for 2 hours at room temperatureu Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance :not have air bubbles, breakage and so on. 7.2 Low temperature testafter putting panel at -20 for 96 hours ,then leaving for 2 hours at room temperatureu Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance:not have air bubbles, breakage and so on.7.3 Temperature and humidity testafter putting panels at 50，90% for 96 hours ,then leaving for 2 hours at room temperatureu Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance:not have air bubbles, breakage and so on. Page :4 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationReliability test7.4 Repetition of high and low temperature testafter putting panels at the condition of -20 for 30 min and then 70 85%RH for 30minand this process is repeated by 20 cycles, then leaving for 24 hours at room temperature.u Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance:not have air bubbles, breakage and so on.70 85%RH -20 -20 1 Cycle 30 min 30 min 30 min 30 min 7.5 Punching TestPunching 1,000,000 times with the D2.0mm silicon rubber Pencil force:60g , speed:5/secu Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance:not have air bubbles, breakage and so on.7.6 Operation life More than 1,000,000 timesPage : 5 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationReliability test76.6Impact testNo damage when 9mm 5.5 gram steel ball is dropped on the touch panel surface from 30 9mmCM height at 1 time. 30CMu Operation Force：1Nu Connector resistance :10M DC25Vu Bear voltage: AC. 25V (50Hz 0.5mA)u Appearance:not have air bubbles, breakage and so on. Page : 6 of 8Shen Zhen DPT-TOUCH Co.,LtdDigital touch panel product specificationAppearance inspection standard 8Appearancecheck anble 8.1 Inspection condition：8.11 The lightness of place : 500LUX60 min60 min8.12 The distance of eyeshot : 30 CM (the panel must be checked under the light transparency condition) 8.13 The angle of eyeshot : 60 8.14 The light source of place :natural sunlight8.2 InspectionItemSpecificationAccept numberSpot ,otherness（B/W Spot）0.1mmIgnorance0.15mm0.3mm20.4mm0Spot sameness （Contrast Spot）0.1mmIgnorance0.15mm0.3mm30.4mm0Cicatrices （Line）L3mm W0.03mmIgnoranceL5mm&W0.08mm2L5mm&W0.1mm08.3 Quality inspection standardAdapt to JIS-Z0915 general standard AQL Cr 0.00% Broken seriously (otherness ,scrape)AQL Ma 0.25% Obvious (otherness ,scrape)AQL Ma 0.65 % Not obvious (otherness ,scrape)Page : 7 of 8Shen Zhen DPT-TOUCH Co.,Ltd4 wire touch panel product specification9. Precautions in useIn order to prevent accidental use and performance deterioration, please keep the following precautions and inhibited points.9.1 Cautions for storageStore the products at the temperature and humidity mentioned in the specification in a state storage of package with care not to expose the products to the direct-sunlight or stresses.9.2 cautions for handlingTransparency is an important factor for the product. So ,please wear clean fingertip, gloves and mask to protect the products from fingerprint or stain attach ,and also hold the portion outside the view area when handling the panel.Please use fingertip or gloves to avoid injuries by sharp edges when handling the Film-glass type touch panel because of the glass edges are not chamfered.Do not handle the product by holding the flexible pattern portion in order to assure the reliability.10.0 Cautions for installing and assembling:1) Do not give excessive strain to the product. Because flexible pattern cable is connected to the body by heat-seal (thermal pressure) method. So ,do not apply excessive forces to the flexible pattern2) Do not add an excessive force to a FPC (Flex tail)that makes peeling off of the FPC from the product .3) Do not fix ,adhere or mount any additional goods on the FPC such as additional film/plate on the FPC. Because such additional goods emphasizes a stress applied at the tip of FPC and it works tearing off the root of FPC from touch panel.4) The transparent touch panel is provided with an air groove . therefore please design the structure not to store any liquid or any fine particles near it .5) In order to not apply load o the surface of the touch panel , please keep a clearance of 0.2mm-0.5mm between touch panel and case.6) We recommend to design a case that it covers the boundary of the active area inside in order to prevent an operation at outside of the active area which can not gua