在以下的小节是在描述如何设定cisco.doc_第1页
在以下的小节是在描述如何设定cisco.doc_第2页
在以下的小节是在描述如何设定cisco.doc_第3页
在以下的小节是在描述如何设定cisco.doc_第4页
在以下的小节是在描述如何设定cisco.doc_第5页
已阅读5页,还剩3页未读, 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

Configuring the CISCO 2500在以下的小節是在描述如何設定cisco 2500 routerBooting the Router Configuring the Ethernet Interface Configuring the Serial Port for Synchronous Communication Configuring the Serial Port for Asynchronous Communication Saving the Configuration Checking the Configuration Settings Booting the Router將盒中所附的8 pin的console線裝在cisco 2500 router的console port上,另一端的線頭則裝在盒中所附的 com port的轉接頭上 , 然後再接到PC的com1或com2上 .在PC上執行TERMINAL(終端機)或TELEX並設定com port和9600的連接速率 .將cisco 1600 router的電源線接上和把10-Base T的網路線接上 .Using the System Configuration Dialogusing the System Configuration Dialog的router設定,請照以下的步驟 : 步驟一 : 將cisco 2500的開關打開 , cisco 2500 console port連線的初始值為 9600 baud, 8 data bits, no parity, and 1stop bits, none flowcontrol .步驟二 : 開機30秒後 , PC的螢光幕上會出現以下的訊息 , 如果有 , router便啟動完成 .System Bootstrap, Version 11.0(10c), SOFTWARECopyright (c) 1986-1996 by cisco Systems2500 processor with 2048 Kbytes of main memoryNotice: NVRAM invalid, possibly due to write erase.F3: 5280396+64388+262188 at 0x3000060 Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706Cisco Internetwork Operating System SoftwareIOS (tm) 2500 Software (C2500-D-L), Version 11.2(10), RELEASE SOFTWARE (fc1)Copyright (c) 1986-1997 by cisco Systems, Inc.Compiled Mon 10-Nov-97 17:28 by ckralikImage text-base: 0x0302B3D0, data-base: 0x00001000cisco 2500 (68030) processor (revision N) with 2048K/2048K bytes of memory.Processor board ID 06929255, with hardware revision 00000000Bridging software.X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)32K bytes of non-volatile configuration memory.8192K bytes of processor board System flash (Read ONLY)Notice: NVRAM invalid, possibly due to write erase. - System Configuration Dialog -At any point you may enter a question mark ? for help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets .Would you like to enter the initial configuration dialog? yes: 步驟三 : 開始設定程序 , 請按Enter或按Yes鍵 步驟四 : 接下來系統會問你是否要看一些介面的資訊 , 請按Enter或按Yes鍵 First, would you like to see the current interface summary? yes: yes Any interface listed with OK? value NO does not have a valid configurationInterface IP-Address OK? Method Status ProtocolEthernet0 unassigned NO not set up upSerial0 unassigned NO not set down down步驟五 : 設定路由器名稱 , 初始值為 routerConfiguring global parameters: Enter host name Router: lan_a下一個 , 將選擇輸入一個 enable secret password. 要輸入下列兩種password : enable secret password (a very secure, encrypted password) enable password (a less secure, nonencrypted password) 接著輸入一個 enable secret password : The enable secret is a one-way cryptographic secret used instead of the enable password when it exists. Enter enable secret: ciscoThe enable password is used when there is no enable secretand when using older software and some boot images. 接著輸入一個 enable password : Enter enable password: class Enter virtual terminal password: ciscoConfigure SNMP Network Management? yes: no 在你的router上設定適當的協定 , 例如 : AppleTalk, IPX, or IP. 以下的例題就是在表示router 如何去設定AppleTalk routing: Configure AppleTalk? no: no Multizone networks? no: no 以下的例題就是在表示router 如何去設定 IPX routing: Configure IPX? no no 如果你使用 IP routing , 你必須要設定一個 IP routing協定 . 有兩種 routing protocols分別是 : Interior Gateway Routing Protocol (IGRP) 或 Routing Information Protocol (RIP) 以下的例題就是在表示router 如何去設定 IP and IGRP routing: Configure IP? yes: yes Configure IGRP routing? yes: no Your IGRP autonomous system number 1: 15 Configure RIP routing? no: yesConfiguring the Ethernet InterfaceEthernet interface的router設定,請照以下的步驟 :步驟一 : 設定 Ethernet 0, 請按Enter或按Yes鍵 : Configuring interface parameters: Configuring interface Ethernet0: Is this interface in use? yes: yes步驟二 : 設定 Ethernet interface的 IP routing , 以下是這些結果 : Configure IP on this interface? yes: yes Configure IP unnumbered on this interface? no: no IP address for this interface: Subnetmask for this interface: (參考)步驟三 : 設定 AppleTalk routing在Ethernet port上 , 以下是這些結果 : Configure AppleTalk on this interface? no: yes Extended AppleTalk network? no: yes AppleTalk starting cable range 2: 2 AppleTalk ending cable range 2: 2 AppleTalk zone name myzone: salesIf applicable, enter an additional zone name. Each time you enter a zone name, you will be prompted to enter an additional zone name. When you have finished entering zone names, press Return. AppleTalk additional zone name: marketing AppleTalk additional zone name:(參考)步驟四 : 設定 IPX routing在Ethernet port上 , 以下是這些結果 : Configure IPX on this interface? no: yes IPX network number 1: 1Configuring the Serial Port for Synchronous Communicationserial port在synchronous communication下的router設定,請照以下的步驟 :步驟一 : 設定 Serial 0 , 請按Enter或按Yes鍵 : Configuring interface Serial0: Is this interface in use? yes: yes步驟二 : 設定 synchronous serial port的 IP routing , 以下是這些結果 : Configure IP on this interface? yes: yes configure IP unnumbered? no: no IP address for this interface: Subnetmask for this interface: 步驟三 : 設定 IGRP routing在asynchronous serial port 上 , 以下是這些 結果 :Configure IGRP routing? yes: no Your IGRP autonomous system number 1: 1 Configure RIP routing? no: yes(參考)步驟四 : 設定 AppleTalk routing在synchronous serial port 上 , 以下是這些 結果 :Configure AppleTalk on this interface? no: yes Extended AppleTalk network? yes yes AppleTalk starting cable range 2: 3 AppleTalk ending cable range 2: 3 AppleTalk zone name myzone: zzserial AppleTalk additional zone name: (參考)步驟五 : 設定 IPX routing在synchronous serial port , 以下是這些結果 : Configure IPX on this interface? no: yes IPX network number 2: 2Saving the Configuration以上的環境都設定好後 , 系統會把ROUTER的設定值重新再顯示一變 , 此時便可檢查設定是否正確 , 以下是這些結果 : The following configuration command script was created: hostname lab_aenable secret 5 $1$7gA0$sLxUbQPZMKXe6oxU.le7M0enable password classline vty 0 4password cisco!interface Ethernet0 ip address !interface Serial0 ip address !interface Serial1 no ip address shutdown!router rip network network !endUse this configuration? yes/no: yes#use the enabled mode configure command to modify this configuration.You have now completed the initial configuration.如果正確請按YES鍵即可 .Checking the Configuration Settings完成設定後router會reboot, 當你看到 press enter to get start!時,按enter鍵則會出現lab_a,在lab_a輸入enable然後按enter鍵,會出現password:, 輸入之前設定的enable screct password, 就完成了login的動作.lan_a enablePassword: lan_a #如想查看現有設定, 請打Show running-configure:Router # sh run如果要查看IOS 的版本 , 就請打show version , 以下是這些結果 :Router show version Cisco Internetwork Operating System SoftwareIOS (tm) 1600 Software (C1600-Y-L), Version 11.1(12)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)Copyright (c) 1986-1997 by cisco Systems, Inc.Compiled Mon 09-Jun-97 14:20 by krunyanImage text-base: 0x0801A214, data-base: 0x02005000ROM: System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)ROM: 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)Router uptime is 5 minutesSystem restarted by power-onSystem image file is flash:c1600-y-l.111-12.AA, booted via flashcisco 1603 (68360) processor (

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

最新文档

评论

0/150

提交评论