cisco-动态路由配置.docx

精品文档cisco 动态路由配置路由0配置Routerenable /进入特权模式Router#configure terminal /全局模式Router(config)#interface f0/0 /进入f0/0端口Router(config-if)#ip address 10.1.1.1 255.255.255.0 /配置端口ipRouter(config-if)#no shut /开启端口Router(config-if)#exit /退出全局模式Router(config)#interface s1/0 /进入s1/0端口Router(config-if)#ip address 192.168.0.1 255.255.255.0 /配置端口ipRouter(config-if)#clock rate 64000 /设置时钟频率Router(config-if)#no shut /开启端口Router(config-if)#exit Router(config)#router rip /创建rip路由进程Router(config-router)#version 2 /配置发送版本Router(config-router)#network 10.1.1.0 /定义关联网络 与路由相连的网络Router(config-router)#network 192.168.0.0 /定义关联网络 与路由相连的网络Router(config-router)#exit/查看ip routRouter#show ip routCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masksR 10.0.0.0/8 120/1 via 192.168.0.2, 00:00:11, Serial1/0C 10.1.1.0/24 is directly connected, FastEthernet0/0C 192.168.0.0/24 is directly connected, Serial1/0R 192.168.1.0/24 120/1 via 192.168.0.2, 00:00:11, Serial1/0路由1配置Routerenable Router#configure terminal Router(config)#interface f0/0Router(config-if)#ip address 10.2.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#interface s1/0Router(config-if)#ip address 192.168.0.2 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#interface s1/1Router(config-if)#ip address 192.168.1.1 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutRouter(config-if)#exit Router(config)#router ripRouter(config-router)#network 192.168.0.0Router(config-router)#network 192.168.1.0Router(config-router)#network 10.0.0.0 /network 直连主类网络 Router(config-router)#version 2Router(config-router)#exitRouter#show ip routCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masksR 10.0.0.0/8 120/1 via 192.168.0.1, 00:00:24, Serial1/0 120/1 via 192.168.1.2, 00:00:22, Serial1/1C 10.2.1.0/24 is directly connected, FastEthernet0/0C 192.168.0.0/24 is directly connected, Serial1/0C 192.168.1.0/24 is directly connected, Serial1/1路由2配置Routerenable Router#configure terminal Router(config)#interface f0/0Router(config-if)#ip address 10.3.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#interface s1/0Router(config-if)#ip address 192.168.1.2 255.255.255.0Router(config-if)#no shutRouter(config)#exitRouter(config)#router rip Router(config-router)#version 2 Router(config-router)#network 10.0.0.0Router(config-router)#network 192.168.1.0 Router(config-router)#exitRouter#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masksR 10.0.0.0/8 120/1 via 192.168.1.1, 00:00:01, Serial1/0C 10.3.1.0/