模具专业英语.docx

模具專業英語模具專業英語一、入水：gate進入位：gate location水口形式：gate type大水口：edge gate細水口： pin-point gate水口大小：gate size轉水口：switching runner/gate唧嘴口徑：sprue diameter二、流道: runner熱流道：hot runner,hot manifold熱嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圓形流道：round(full/half runner流道電腦分析：mold flow analysis流道平衡:runner balance熱嘴：hot sprue熱流道板：hot manifold發熱管：cartridge heater探針: thermocouples插頭：connector plug插座： connector socket密封/封料： seal三、運水：water line喉塞：line lpug喉管：tube塑膠管：plastic tube快速接頭：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold邊釘/導邊：leader pin/guide pin邊司/導套：bushing/guide bushing中托司：shoulder guide bushing中托邊L：guide pin頂針板：ejector retainner plate托板：support plate螺絲： screw管釘：dowel pin開模槽：ply bar scot內模管位：core/cavity inter-lock頂針：ejector pin司筒：ejector sleeve司筒針：ejector pin推板：stripper plate縮呵：movable core,return core core puller扣機（尼龍拉勾）：nylon latch lock斜頂：lifter模胚（架）： mold base上內模：cavity insert下內模：core insert行位（滑塊）： slide鑲件：insert壓座/斜雞：wedge耐磨板/油板：wedge wear plate壓條：plate撐頭: support pillar唧嘴： sprue bushing擋板：stop plate定位圈：locating ring鎖扣：latch扣雞：parting lock set推杆：push bar栓打螺絲：S.H.S.B頂板：eracuretun活動臂：lever arm分流錐：spure sperader水口司:bush垃圾釘：stop pin隔片：buffle彈弓柱：spring rod彈弓:die spring中托司：ejector guide bush中托邊：ejector guide pin鑲針：pin銷子：dowel pin波子彈弓：ball catch喉塞: pipe plug鎖模組：lock plate斜頂：angle from pin斜頂杆：angle ejector rod尼龍拉勾：parting locks活動臂：lever arm復位鍵、提前回杆：early return bar氣閥：valves斜導邊：angle pin術語：terms承壓平面平衡：parting surface support balance模排氣：parting line venting回針碰料位：return pin and cavity interference模總高超出啤機規格：mold base shut hight頂針碰運水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用鑲件： Do not use (core/cavity) insert用鈹銅做鑲件： use beryllium copper insert初步（正式）模圖設計：preliinary (final) mold design反呵：reverse core彈弓壓縮量：spring compressed length穩定性好：good stability,stable強度不夠：insufficient rigidity均勻冷卻：even cooling扣模：sticking熱膨脹：thero expansion公差：tolorance銅公(電極）：copper electrodedowel pin 定位梢draft 拔模錐度draw bead 張力調整杆drive bearing 傳動軸承ejection pad 頂出襯墊ejector 脫模器ejector guide pin 頂出導梢ejector leader busher 頂出導梢襯套ejector pad 頂出墊ejector pin 頂出梢ejector plate 頂出板ejector rod 頂出杆ejector sleeve 頂出襯套ejector valve 頂出閥eye bolt 環首螺栓filling core 椿入蕊film gate 薄膜形澆口finger pin 指形梢finish machined plate 角形範本finish machined round plate 圓形範本fixed bolster plate 固定側範本flanged pin 帶凸緣銷flash gate 毛邊形澆口flask 上箱floating punch 浮動沖頭gate 澆口gate land 澆口面gib 凹形拉緊楔goose neck 鵝頸管guide bushing 引導襯套guide pin 導梢guide post 引導柱guide plate 導板guide rail 導軌head punch 頂頭沖孔headless punch 直柄沖頭heavily tapered solid 整體模蕊盒hose nippler 管接頭impact damper 緩衝器injection ram 壓射柱塞inlay busher 嵌入襯套inner plunger 內柱塞inner punch 內沖頭insert 嵌件insert pin 嵌件梢king pin 轉向梢king pin bush 主梢模具生產相關英文.difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head掛鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓衝子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線衝子air-cushion eject-rod氣墊頂杆spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊capability能力parameter參數factor係數phosphate皮膜化成viscosity塗料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping衝壓molding成型spare parts=buffer備品coordinate座標dismantle the die折模auxiliary fuction輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除鏽機degate打澆口dryer烘乾機induction感應induction light感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=peuet=grain細粒grit maker抽粒機cushion緩衝magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane刨grind磨drill鑽boring鏜blinster氣泡fillet鑲;嵌邊through-hole form通孔形式voller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸augular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸)draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting衝壓鉚合side stretch側衝壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號)shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印衝壓名稱類extension dwg展開圖procedure dwg工程圖die structure dwg模具結構圖material材質material thickness料片厚度factor係數upward向上downward向下press specification衝床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves=spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套範本類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上範本lower plate下範本die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)stripping plate內外打(脫料板)outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件)deburring punch壓毛邊衝子groove punch壓線衝子stamped punch字模衝子round punch圓衝子special shape punch異形衝子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂杆trimming punch切邊衝子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋衝子reel-stretch punch卷圓壓平衝子guide plate定位板sliding block滑塊101個熱處理常用英文辭彙1. indication 缺陷2. test specimen 試樣3. bar 棒材4. stock 原料5. billet 方鋼，鋼方坯6. bloom 鋼坯,鋼錠7. section 型材8. steel ingot 鋼錠9. blank 坯料，半成品10. cast steel 鑄鋼11. nodular cast iron 球墨鑄鐵12. ductile cast iron 球墨鑄鐵13. bronze 青銅14. brass 黃銅15. copper 合金16. stainless steel不銹鋼17. decarburization 脫碳18. scale 氧化皮19. anneal 退火20. process anneal 進行退火21. quenching 淬火22. normalizing 正火23. Charpy impact text 夏比衝擊試驗24. fatigue 疲勞25. tensile testing 拉伸試驗26. solution 固溶處理27. aging 時效處理28. Vickers hardness維氏硬度29. Rockwell hardness 洛氏硬度30. Brinell hardness 布氏硬度31. hardness tester硬度計32. descale 除汙，除氧化皮等33. ferrite 鐵素體34. austenite 奧氏體35. martensite馬氏體36. cementite 滲碳體37. iron carbide 滲碳體38. solid solution 固溶體39. sorbite 索氏體40. bainite 貝氏體41. pearlite 珠光體42. nodular fine pearlite/ troostite屈氏體43. black oxide coating 發黑44. grain 晶粒45. chromium 鉻46. cadmium 鎘47. tungsten 鎢48. molybdenum 鉬49. manganese 錳50. vanadium 釩51. molybdenum 鉬52. silicon 矽53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷55. nitrided 氮化的56. case hardening 表面硬化，表面淬硬57. air cooling 空冷58. furnace cooling 爐冷59. oil cooling 油冷60. electrocladding /plating 電鍍61. brittleness 脆性62. strength 強度63. rigidity 剛性,剛度64. creep 蠕變65. deflection 撓度66. elongation 延伸率67. yield strength 屈服強度68. elastoplasticity 彈塑性69. metallographic structure 金相組織70. metallographic test 金相試驗71. carbon content 含碳量72. induction hardening 感應淬火73. impedance matching 感應淬火74. hardening and tempering 調質75. crack 裂紋76. shrinkage 縮孔，疏鬆77. forging 鍛（件）78. casting 鑄（件）79. rolling 軋（件）80. drawing 拉（件）81. shot blasting 噴丸（處理）82. grit blasting 噴鋼砂（處理）83. sand blasting 噴砂（處理）84. carburizing 滲碳85. nitriding 滲氮86. ageing/aging 時效87. grain size 晶粒度88. pore 氣孔89. sonim 夾砂90. cinder inclusion 夾渣91. lattice晶格92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性93. spectrum analysis光譜分析94. heat/thermal treatment 熱處理95. inclusion 夾雜物96. segregation 偏析97. picking 酸洗，酸浸98. residual stress 殘餘應力99. remaining stress 殘餘應力100. relaxation of residual stress 消除殘餘應力101. stress relief 應力釋放機械類常用英語：衝壓模具-零件類punch沖頭insert入塊(嵌入件)deburring punch壓毛邊衝子groove punch壓線衝子stamped punch字模衝子round punch圓衝子special shape punch異形衝子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂杆trimming punch切邊衝子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋衝子reel-stretch punch卷圓壓平衝子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂杆spring-box eject-plate彈簧箱頂板bushing bolck襯套cover plate蓋板guide pad導料塊各式模具分類用語英漢對照landed plunger mold 有肩柱塞式模具burnishing die 擠光模landed positive mold 有肩全壓式模具button die 鑲入式圓形凹模loading shoe mold 料模式模具center-gated mold 中心澆口式模具loose detail mold 活零件模具chill mold 冷硬用鑄模loose mold 活動式模具clod hobbing 冷擠壓制模louvering die 百葉窗沖切模composite dies 複合模具manifold die 分歧管模具counter punch 反凸模modular mold 組合式模具double stack mold 雙層模具multi-cavity mold 多模穴模具electroformed mold 電鑄成形模multi-gate mold 複式澆口模具expander die 擴徑模offswt bending die 雙折冷彎模具extrusion die 擠出模palletizing die 疊層模family mold 反套製品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通氣性模具duplicated cavity plate 複板模positive mold 全壓式模具fantail die 扇尾形模具pressure die 壓緊模fishtail die 魚尾形模具profile die 輪廓模flash mold 溢料式模具progressive die 順序模gypsum mold 石膏鑄模protable mold 手提式模具hot-runner mold 熱流道模具prototype mold 雛形試驗模具ingot mold 鋼錠模punching die 落料模lancing die 切口模aising(embossing) 壓花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 無流道冷料模具sectional die 對合模具segment mold 組合模semi-positive mold 半全壓式模具shaper 定型模套single cavity mold 單腔模具solid forging die 整體鍛模split forging die 拼合鍛模split mold 雙並式模具sprueless mold 無注道殘料模具squeezing die 擠壓模stretch form die 拉伸成形模sweeping mold 平刮鑄模swing die 振動模具three plates mold 三片式模具trimming die 切邊模unit mold 單元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 軛型模注塑模部分中英文對照塑膠成形模具 mould for plastics 熱塑性塑膠模 mould for thermoplastics 熱固性塑膠模 mould for