Alcatel产品可靠性检验标准.doc

产品质量测试标准常规性能测试项目及标准序号试验项目试验目的试验方法或条件判定标准备注1关机电流测试测试手机在关闭状态下内部电路消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V一般情况下0.1mA。2待机电流测试手机开机并完成自检的全过程（2至3分钟）后，手机处于睡眠（3秒）和检测广播信道（1秒）的交替工作状态时所消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V待机电流10mA3开机通话电流测试在手机建立呼叫连接，通话时，手机所消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V按设计要求进行4背光灯电流测试测试手机在待机或测试模式下打开背光灯（LCD背光和键盘背光）时背光灯自身所消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V200mA，或根据背光灯性质、型号、种类的不同而有所不同。5蜂鸣器电流测试测试铃声或音乐声设置为最大音量（响度）时，蜂鸣器发音时所消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V按设计要求进行6振动电流测试测试手机在振动时内部小电机转动时所消耗的电流正常温湿条件： 温度为: 15 35,相对湿度：20%75% ；极限温湿条件： 温度：-10 +55测试过程中，被测设备的电源由测试电源代替。测试电源的供电电压为待测设备标称工作电压。高压：4.2V；低压：3.6V；常压：3.8V90mA，或根据电机型号、种类和驱动电路的不同而略有差异7接收信号强度测试测试手机接收微弱信号的能力取手机RF接口或双工输出端，并与综测仪连接，调节综测仪广播控制信道的BS/RX LEV，观察手机信号显示条，并使手机的信号显示条从高到低依此递减，记录每格信号条时的手机接收电平，即可得出手机接收信号强度如果无某格信号条或BCCH Level异常，则为不合格。8电池电量测试测试手机电池在充放电情况下容量在额定值（MA/H）之间的变量将高速可编程电源输出电压调4.2V，并给假电池供电，然后再用假电池给手机提供工作电源，并由高到低调节高速可编程电源的输出电压，观察手机电池显示条，记录电池显示条依此递减时每格显示条的电压，以检验电压和显示条是否相符电压和显示条相符（注：标准电压3.7V时手机电量格数应为1-2格）9振铃声级测试检验手机的振铃声级电平是否达到规范标准和设计要求手机的铃声分贝测试一般随机选取5台手机在一个安静的环境中进行测试。测试时，手机插上SIM卡处在待机状态，来电提示要设为响铃模式，响铃音量调至最大、合上翻盖，放置在硬木板上。声级计与手机在同一直线上，相距30CM，且与手机所在的平面成45度角。用另一手机呼叫待测试手机，在待测试手机响铃时，观察声级计上的读数，即为该手机在此种铃声下的铃声分贝值。测试每一手机的每一种铃声的分贝值75dBA10 MP3/MP4响度测试检验手机的MP3/MP4电平是否达到规范标准和设计要求1、被测手机播放测试信号。测试信号为指定的音乐文件（如：TCT拥有版权的“想唱就唱.MP3”和“希望.MP3”）。2、使用满足IEC651 Type0/1要求的测量麦克风沿最大声强方向距离被测手机30CM固定。3、在整个信号周期内进行音频信号采样，采样频率为48KHz。4、使用音频分析仪对信号加Hanning窗并进行4096点FFT，Overlad为75。5、 使用A计权对200Hz3500Hz范围内的信号进行计算。想唱就唱（筱筱）.MP3 大于：70dB20Pa(A) 希望（江堰）.MP3 大于：65dB20Pa(A) 11FTA测试全面检测手机的射频和协议性能1、测试设备：英国Anite公司生产的RAMS和SAT（A）4。2、测试项目：依据GCF-CC要求的测试项目。3、测试方法及要求：依据3GPP TS 51.010-1提供的测试方法和要求。依据3GPP TS 51.010-1提供的标准进行判定。可靠性实验标准 Reliability Test Standard序号No.实验项目Test Item实验目的Test Purpose实验方法及实验条件Test Method and Condition样品数Sample判定标准Judgement Standard备注Remark模拟测试 Simulation test1待机时间测试 Idle time test测试手机开机并完成自检的全过程（2至3分钟）后，手机处于睡眠（3秒）和检测广播信道（1秒）的交替工作状态时电池电量下降至手机自动关机时所用的时间。After the handset power on and all the self test(about 23minutes),alternated Idle 3 seconds and broadcast channel test 1 sencond,measure the time when the battery declined to the a电池在额定容量下，手机开机并完成自检后，分别置于移动网、联通网及白卡，至到自动关机为止。记录各自手机的待机时间，5台平均即为手机待机时间；要求翻/滑盖手机，处于合盖状态，关闭其它设置，网络信号在-65-85dBm范围内。The battery with rate capacity. After the handset power on and all the self test, Mobile Card, Unicom Card and White Care division of idle tim5PCS推荐大于200小时（具体按产品定义）Commended more than 200 hrs (According to the product SPEC)移动网、联通网要求待机时间150小时。白卡测试结果供参考。2通话时间测试Communication time test测试手机在通话时，电池在额定容量下维持手机通话的最长时间.The battery with rate capacity, Inspect the max time to communicate with the handset.电池在额定容量下，将手机听筒音量开到最大，分别在移动网和联通网，手机呼叫建立通话联系后，至到自动关机为止。记录各自手机的通话时间，5台平均即为手机通话时间；要求手机关闭其它设置，网络信号在-65-85dBm范围内.The battery with rate capacity, the volume set the max.Mobile Card and Unicom Card division of communication. Record each set the longest commun5PCS推荐大于120分钟（具体按产品定义）Commended more than 120 minutes (According to the product SPEC)3温升实验Temperature rise test验证手机在通话过程中，手机温度是否会升高并超过标准要求.Inspect the temperature variety of handset during communicating.最大功率发射。并工作于CH62。装入低电电池，开机、充电状态下将手机与模拟基站建立连接，持续通话90分钟。持续通话中，听筒音量开到最大，实时测量手机表面（按键、电池表面）、听筒部分的温度值；分别以90分钟内测量到的手机表面及听筒部分的最高温度值为最终实验温度。The handsets with the max transmit power in channel 62, Low electrical voltage, power on and charge. Communicate with the2PCS通话过程中不能出现掉话现象，试验后功能、性能正常。手机表面温度上升不超过15，听筒部分不能超过12.Interrupted exception is not allowed during the test. The function and performance is normal after test. The surface temperature variety is not more than 15. The receiver temperature variety is not mor环境试验 Environment Test4高低温贮存Hot/Cold test in storage验证手机在高低温环境条件下贮存的适应性Validate the capacity of the handset to be stored in low and high temperature conditions.被测样机不包装、不通电状态放进具有20的试验箱内。使试验箱在30分钟内温度达到-253，温度稳定后持续48小时,然后在30分钟内又使温度回到20;在30分钟内使试验箱内温度达到702，温度稳定后持续48小时，再在30分钟内使试验箱内温度回复到20，放置期满，被测样机进行试验后检查。Put the unpacked and power off samples in the test box in 20 temperature.The room temperature reduce to10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.5高低温工作Hot/Cold test in operation验证手机在高低温环境条件下使用的适应性Validate the capacity of the handset to be operation in low and high temperature conditions.被测样机不包装、处于通电待机状态，放进具有20的试验箱内。使温度在30分钟内达到-203，温度稳定后持续16时，然后在30分钟内又使温度回到20；再使试验箱在30分钟内温度达到+552，温度稳定后持续16小时，再在30分钟内使试验箱内温度回复到20，持续期满。立即进行被测样机试验后检查。Put the unpacked and switched on samples in the test box in 20 temperature.The room temperature reduc10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.6恒定湿热Damp Heat test验证手机在恒定湿热环境条件下使用的适应性.Inspect the performance of the handset under high temperature and high humidity.被测样机不包装、处于通电待机状态，以翻盖打开位置放进试验箱内。使温度达到+402，湿度达到95%（+2%/-3%），稳定后持续96小时，持续期满。立即进行被测样机试验后检查。put the unpacked, power on and folder opened samples into the constant temperature box. When the temperature arrive retentively +402 and humidity is 95（+2%/-3%）10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.7温度冲击实验Thermal shock test验证手机经受环境温度迅速变化的能力.Inspect the performance of the handset under the vertiginous temperature.被测样机不包装、不带电池状态，以正常位置放进试验箱内。高温为+702，稳定温度保持时间2h；低温为403，稳定温度保持时间2h；转换时间不大于5分钟；循环次数为12次（1个循环周期为4小时5分钟）。循环期满，在正常大气条件下放置2h。放置期满，被测样机进行试验后检查。put the unpacked and power off 5pcs QC pASSED samples into the Thermal Shock Box. High temperature is 702, keep t10PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.8结露实验Dew test验证手机在结露环境下的适应性.Validate the performance of the handset under the dew environment.待机状态下，按照+202/95%（+2%/-3%）湿度放置2h；-203放置30min；转换时间40min设置进行试验，共连续进行5个循环；试验结束后立即进行测试。The samples idle, Do the test as the temperture is 202 and the humidity is 95%（+2%/-3%） for 2h; then the temperture is -203 for 30minutes, conversion time in 40minu5PCS通过基本功能、性能测试；外观和结构正常Base function and performance test is OK; Appearance and structure are normal.9污物混入实验Filth interfuse test验证手机结构密闭性.Validate the frame obturation of the handset.将电池装在手机上，关机状态下放入装有300目滑石粉的袋子中，上下振荡200次，左右振荡200次，前后振荡200次，共计600次。完成后取出观察主屏、副屏进尘程度。put the power off and with battery samples in the bag with talcuum powder 300 mesh, surge up and down 200 times, surge around 200 times, surge front and back 200 times, 605PCS污物不得进入LCD内，手机功能正常。LCD havent any filth. The function is normal.10极限温度充电实验Limit temperature Charge Test验证手机在极限温度条件下的充电性能Validate the performance of the handset to charge under the limit temperature condition.分别在-53及+452温度下，在手机达到环境温度并且稳定后充电30分钟，电池电压能够上升。Under the temperture -53 and +452, Alternate charge the handset for 30minutes, the battery voltage must rise.5PCS手机充电指示正常（即充电指示灯点亮，充电图标跑动）；在手机达到环境温度并且稳定后充电30分钟，电池电压能够上升。The charge is show normal(the charge LED is light, charge ico is running); The battery voltage has risen after chargeing 30 minutes.11盐雾实验Salt mist test验证手机产品抗盐雾腐蚀的能力 Validate the resistance of the handset in the salt mist.溶液含量为5%的氯化钠溶液。将手机关机放在盐雾试验箱内(箱内温湿度分别为+352，90%（+2%/-3%）RH)，样机.竖直放置24h、正面放置10h、反面面放置10h，以免溶液喷洒不均或有的表面喷不到，样机需立即被放入测试箱。实验期满。取出样机，清水擦拭后烘干，进行试验后检查。put 5% NaCI liquor into the tester. put the power off samples in the salt mist test box(the room temperture is +3PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.12随机振动Random Vibration Test验证手机经受规定严酷等级的随机振动的能力Validate the performance of the handset under asperity vibration athletics.被测样机不包装、处于通电待机状态。牢固固定在试验台上。试验参数：+6dB/oct，频率范围10-20Hz ；频率范围20-500Hz，功率频谱密度0.05 g2/Hz。轴向：三个轴向。持续时间：每方向1小时，共3小时。持续时间结束，取出被测样机进行试验后检查。Fixup the unpacked and power on samples on the test table. Test parameter: +6dB/oct，frequency is from 5 to 20Hz and from 203PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.13正弦振动Sinusoidal vibration test模拟手机在运输过程中产生的振动。Simulate the transport vibration, and validate the handsets reliabilty.样机不包装、处于插卡通电待机状态，在振幅1.5mm，频率范围5-10Hz ；在加速度为3g，频率范围10-200Hz ；以1 oct/mn扫频速度进行X、Y、Z三个方向，每个方面各振动1小时，共3个小时，试验结束后进行试验后检测；The samples in unpacked and power on with SIM card. Frequency from 5 to 10Hz, swing is 1.5mm; Frequency from 10 to 200Hz, acceleration is5PCS通过基本功能、性能及外观测试Base function, performance and appearance test is ok.14包装振动packaging vibration endurance Test检验手机包装材料对手机产品的保护作用及手机结构配合、机壳材料的耐磨性、部件焊接质量等Validate the protect ability from the wrapper, structure inosculate of the product, wearability of the shell material and solder quality of the components etc.被测样机包装好放于试验台上。试验参数：频率5-200Hz ，振幅15-20mm，在X、Y、X三个正弦方向各振动1小时，共3小时。持续时间结束，取出被测样机进行试验后检查。put the packed samples on the test table. Test parameter：Frequency from 5 to 200Hz, swing from15 to 20mm, every axis vibrate for 1h, sum up 3h. Duration over,take out an1箱1box样机及手机配件通过基本功能、性能及外观测试；The handset and fittings can pass base function,performance and appearance.15包装跌落packaging drop endurance Test检验手机包装材料对手机及附件的年外观、功能等的保护作用Validate the protect ability of the appearance and function from the wrapper.以包装出货的整箱手机按一角三边六面各跌一次，试验后结样机及配件进行全检。跌落标准如下：当产品毛重G10kg时，进行1M高度跌落；当产品毛重10kgG20kg时，进行80CM高度跌落；当产品毛重G20kg时，则进行60CM高度跌落；The handset packed with case waiting for shipment, drop 1 time of 1 angle, 3 edges, 6 faces. Final check of the samples and fittings1箱1box样机及手机配件通过基本功能、性能及外观测试；允许不多于2个（含2个）的内部包装破裂、损伤。The handset and fittings can pass base function,performance and appearance; Allow the inner packing and destroy crack 2 boxes at the most.161M跌落实验1M drop test验证手机及电池抗多次跌落于地上的能力Validate the capacity of the handsets and battery to resist being dropped repeatedly onto concrete.被测样机不包装、处于插卡通电待机状态。从1m高度（屏幕小于2.4,或不超过屏本身所在面积的40%)，初速度为0并自由跌落于光滑混凝土地面上，6个面、4条边，每面跌落2次,每条边跌1次，共计16次。每4次对样机外观、功能进行全检，试验结束，对样机进行全面检查。配套电池跌落：6个面、上方左右2条边各跌一次，共计8次，每2次对进行检查，试验结束，对电池进行全面检查。The samples unpacked and power on with SIM card, then drop from 1 mete10PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or abnormity.该项待有手机实物时，再进行实际测量，若屏幕超过屏本身所在面积的40%，则改做0.5m跌落实验17滚筒跌落Barrel Test确定手机频繁跌落到硬表面时，经受重复跌落的适应性Confirm the capacity of the handsets to resist being dropped repeatedly onto rigidity face.频率：5转/分钟，即手机跌落10次/分钟；次数：旋转500转，即手机跌落1000次；每跌落200次，进行外观检查，有无部件松脱，可复原装回再进行下一次试验；每跌落200次进行基本功能测试，记录外观结构损伤地方和功能异常项目。试验结束检查按外观结构检查基本功能测试RF测试开壳检查顺序进行。Frequency: 5 circles/minute, namely the handsets dropped 10 times/minute; Time: 500 circles, namely the ha5PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or abnormity.1810CM微跌10CM Mini-drop Endurance Test验证手机在使用中产生轻微撞击的适应性Validate the capacity of the handsets to resist being light strike in the using手机插卡开机，合翻盖待机状态下从10cm的高度自由跌落至812mm厚的铝板上，顺序按底面2500次正面500次左侧面500次右侧面500次，跌落完毕为一个循环，共跌4个循环，每完成一个循环检查一次被测样机的外观及基本功能；跌落次数要求16000次；试验速率：15次/分 The handsets power on with SIM card and close the floder to free falls from 10cm high and onto the aluminium board5PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or abnormity.寿命测试 Life test19按键寿命实验Keypad lifetime test验证手机按键的使用寿命及长期按键对周围器件的影响Validate the keypad lifetime of the handset and the influence of the around components after test.被测样机不包装、处于通电待机状态。以5060次/分的速度、3.5N的力度均匀地按键，按下、松开为一次。每2小时进行基本功能测试，记录外观结构损伤地方和功能异常项目，总次数10万次。试验结束后结被测样机按键弹性、表面颜色、字符和功能进行检查，并开壳检查内部结构。The samples unpacked and power on, press the key 5060cycles per minute, and the strength is 3.5N; Do function test，record2PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or abnormity.20按键耐压强度实验Keypad press endurance test验证手机按键经受一定的力度按压较短时间的能力。validate the handsets capacity to withstand a certain number of forces for less times将手机装上电池，关机状态下，使用5mm的金属棒加载98N的静负荷，按压各键1分钟。The handsets power off and with battery, press the key with 5mm metal club in 98N for 1 minute.3PCS外壳不能破损、变形；手机功能正常。The shell cant be damageand or distortion; the function must be normal.21侧按键寿命实验Side keys endurance test验证手机侧按键的使用寿命及长期按键对周围器件的影响Validate the side keys lifetime of the handset and the influence of the around components after test.被测样机不包装、处于通电待机状态。以5060次/分的速度、3.5N的力度均匀地按键，按下、松开为一次。每2小时进行基本功能测试。总次为10万次。The samples unpacked and power on, press the key 5060cycles per minute, and the strength is 3.5N; 100000 times in all.2PCS通过基本功能测试、性能测试，未有明显的裂纹/破损，内部未见零件松动及异常pass base function, performance test: No obviously crack / damage, no inner-components loose or abnormity.22触摸屏测试Touch screen test点击测试dot hit test验证手机触摸屏的使用寿命Validate the use lifetime of the touch screen用与被测样机相配套的POM笔，加载250g力，每秒2次点击用户正常使用触摸屏，点笔可触及的区域（整机屏幕边缘），进行100万次。With the match POM pen to hit the touch screen in 250g for 2 times/second in the touchable area (including the brim of the screen), 1000000 times in all.2PCS表面无损伤，线性度小于1.5Face cant damnify, Linearity less than 1.5%.23划线测试Lineation test验证手机触摸屏的使用寿命Validate the use lifetime of the touch screen用与被测样机相配套的POM笔，加载250g力，每秒1次在用户正常使用触摸屏点笔可触及的区域（整机屏幕边缘），进行10万次划线测试。With the match POM pen to line on the touch screen in 250g for 1time/second in the touchable area (including the brim of the screen), 100000 times in all.2PCS表面无损伤，线性度小于1.5Face cant damnify, Linearity less than 1.5%24人手插拔实验manual insertion-extraction endurance test1.点笔插拔实验Touchpen Endurance Test验证点笔的使用寿命Validate the use lifetime of the touchpen.1、对手写笔与手机进行外观检查并进行配合检查，并测量点笔的拔脱力。2、将手写笔插入手机壁管再拔出，插拔为一次；速率：30次/分钟，试验次数：15000次，实验完成后，再次测量点笔的拔脱力。1.Inspect touchpen and the handset assort. Measure the force of pull out touchpen.2.Insert and pull the touchpen from the samples. Insert and pull as one time3PCS不允许机壳掉漆、手写笔内管与外管变形、漏润滑油、插入壁管内松、紧等不良现象。Do not allow the defects that shell fell off paint, inner or outer pipe distortion, leak lube, lube leak,insert inside pipe loose or tighten etc.2.耳机插拔实验Earphone endurance test验证手机长期插拔耳机对相关器件的影响。 Inspect the earphone endurance effect to the relation component.将耳机垂直方向插入耳机孔之后，再以垂直方向拔出，如此反复插拔。按外观结构检查耳机话音通信检查顺序进行。每200次检查其耳机发受话功能，至3500次时，再以每50次检查其耳机发受话功能，试验次数：5000次。Insert and unplug the earphone vertically, check the samples as appearance & structurethe tone of the earphone, inspect the voice sending and receivi3PCS必须通过耳机话音通信测试；外观和结构正常Voice sending and receivingis of the earphone must normal. Appearance and strucure are OK.3.耳机塞/mini SD塞/I/O口塞插拔实验Earplug/mini SD stopple/and I/O stopple endurance test验证耳塞/mini SD塞/I/O口塞外观及紧固程度Validate the tighten and appearance of the earplug /mini SD stopple/and I/O stopple.1.5Kg0.2Kg，拉伸10秒；正常插拔5000次1.5kg0.2kg,stretch 10 second, 5000times in all.3PCS耳塞/mini SD塞/I/O口塞拔不出，无破损Earplug/mini SD stopple/and I/O stopple cant be pulled out, no disrepair.4.电池插拔实验Battery Connector Endurance Test验证手机长期插拔电池对相关器件的影响。Validate the influence of the correlation parts under the handset to insert and unplug the battery .按正常步骤，装上电池，然后取下电池，如此反复安装，按外观结构检查开机功能测试顺序进行。每插拔100次检查开机是否正常，至1500次时每50次检查开机是否正常。试验次数：3000次。Insert and unplug battery as one cycle, repeat do this operation,check the samples as appearance & structurefunction test.Switch on the handset to inspect the app3PCS试验后电池推纽弹性良好，电池连接器无明显变形，电池无掉漆等外观不良After test,the elasticity of the battery knob must be OK, battery connector no obvious distortion, battery no clumpy paint fell off, and no the same appearance defects；5.SIM卡插拔实验 SIM Card Endurance Test验证手机长期插拔SIM卡对相关器件的影响。Validate the influence of the correlation parts under the handset to insert and unplug SIM Card long-term.按正常步骤，插入SIM卡，然后取下SIM卡，如此反复安装。然后，每插拔100次，按外观结构开机功能测试顺序进行检查。至1500次时，每50次检查一次。试验次数：2000次。Insert and unplug battery as one cycle, repeat do this operation,check the samples as appearance & structurefunction test every 100 times, and every 50 times to inspe3PCS试验后SIM卡扣无变形松动，SIM卡触片无下陷及变形等外观不良After test, the SIM card button no distortion, SIM card connctor no sink and distortion and no the same appearance defects.6.I/O充电口插拔实验Charger I/O Endurance Test验证手机长期插拔充电器对相关器件的影响。Validate the charger I/O endurance effect to the relation components.被测样机不包装、处于通电待机状态，按正常步骤，插拔充电器插头。按外观结构检查充电功能测试顺序进行。每插拔100次检查充电功能是否正常，试验次数：3000次。The samples unpacked and power on, As normal steps to insert and unplug the charger. Inspect order as: appearance & structurecharge function; Inspect the charge function whet3PCS插拔寿命至少为3000次，必须通过充电功能测试。插头、插座无变形、无损伤，无接触不良.Insert and unplug 3000 cycles at least, Charger function test is OK. plug and socket no distortion, damage and any contact NG.7.USB数据线插拔实验USB data cable Endurance Test验证手机长期插拔USB数据线对相关器件的影响。 Inspect the USB data cable endurance effect to the relation component.被测样机不包装、处于通电待机状态，按正常步骤，插拔USB数据线。每插拔100次检查下载功能是否正常，试验次数：3000次。The samples unpacked and power on, As normal steps to insert and unp