几种猫路由设置方法.doc

几种猫路由设置方法合勤 P642首先P642是TELNET模式，所以首先在运行里输入TELNET 确定后开启TELNET！然后点击“连接”“远程系统”在主机名里添入192.168.1.1这是P642默认IP！然后连接出现Password：在后面输入默认的密码1234回车后进入下面的设置界面 Copyright (c) 1994 - 2000 ZyXEL Communications Corp. Prestige 642R Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. SUA Server Setup 99. Exit 这些都是各功能界面按前面的数字和回车来进入各界面！ 下面进入1. General Setup 界面，只要输入“1”回车即可，以此类推！我只登出需要更改的界面！ - Menu 1 - General Setup System Name= p642 （随便起名） Location= Contact Persons Name= Route IP= Yes （要开启路由这里必须改成YES） Route IPX= No Bridge= No （这里必须NO） Press ENTER to Confirm or ESC to Cancel: - 设置好后回车存储，然后按ESC回主界面！ 再进如3. Ethernet Setup 继续进2.TCP/IP and DHCP Setup - Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 202.97.224.68 Secondary DNS Server= 202.97.230.4 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 202.97.224.68和202.97.230.4为当地电信的2个DNS，各地不同。只有一个也可 其他的按照我的设置改即可 回车存储 下面回到主菜单进入4. Internet Access Setup - Menu 4 - Internet Access Setup ISPs Name= ChangeMe （这个名字也随便了） Encapsulation= ENET ENCAP 必须和电信提供参数一致 Multiplexing= LLC-based 必须和电信提供参数一致 VPI #= 0 （VPI VCI值问当地电信） VCI #= 35 Service Name= N/A My Login= N/A My Password= N/A Single User Account= Yes 为开启项，默认为 IP Address Assignment= Static IP Address= 218.10.165.196 （这是电信给你的IP） ENET ENCAP Gateway= 218.10.165.193（这是电信给你的网关 IP，网关每户不同） Press ENTER to Confirm or ESC to Cancel: - 回主菜单进11. Remote Node Setup再继续进1， - Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe 不是一行 Route= IP Active= Yes 不是一行 Bridge= No Encapsulation= ENET ENCAP 不 Edit PPP Options= N/A Multiplexing= LLC-based 不 Rem IP Addr= 218.10.165.193 Incoming: 不 Edit IP/IPX/Bridge= No Rem Login= N/A Rem Password= N/A Outgoing: Session Options: My Login= N/A Edit Filter Sets= No My Password= N/A Authen= N/A Press ENTER to Confirm or ESC to Cancel: - 注意上面应该为两列，为防止混淆我用文字夹在中间了，后面的没夹文字自己注意218.10.165.193为网关 每户都不同！ 进12. Static Routing Setup然后续进1，在进1， Menu 12.1.1 - Edit IP Static Route Route #: 1 Route Name= test Active= Yes Destination IP Address= 0.0.0.0 IP Subnet Mask= 0.0.0.0 Gateway IP Address= 218.10.165.193 Metric= 2 Private= No Press ENTER to Confirm or ESC to Cancel: 以上修改后就可开启路由了！ 另外23. System Password是修改进入密码的！ 24. System Maintenance 然后继续进4再继续进21就自动重起路由器，这在掉线后恢复连接有用！这跟拔掉路由器电源再插上类似，像重起电脑！ 另外24. System Maintenance里面有一项是恢复出厂默认的，具体的忘了，自己试吧！ 记住每页设置完一定要回车存储！ 下面是关于PPPoE模式路由的开启！用telnet登陆，在运行里输入telnet 192.168.1.1。密码初始为1234，进入： Copyright (c) 1994 - 2000 ZyXEL Communications Corp. Prestige 642R-11 Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance 25. IP Routing Policy Setup Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. SUA Server Setup 99. Exit 设置Router 工作模式: 进入菜单1 Menu 1 - General Setup System Name= hfkj Location=huafeng Contact Persons Name=sjz Route IP= Yes Route IPX= No Bridge= No 注意必须打开Route IP 进入菜单3.2 Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 Multicast= None IP Policies= Edit IP Alias= No 进入菜单4 Menu 4 - Internet Access Setup ISPs Name= ChangeMe Encapsulation= PPPoE Multiplexing= LLC-based VPI #= 0 VCI #= 35 Service Name= My Login= 82303#1 My Password=* Single User Account= Yes IP Address Assignment= Dynamic IP Address=N/A ENET ENCAP Gateway= N/A 进入菜单11.1 Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe Route= IP Active= Yes Bridge= No Encapsulation=PPPoE Edit PPP Options=No Multiplexing= LLC-based Rem IP Addr=0.0.0.0 Incoming: Edit IP/IPX/Bridge= No Rem Login= Rem Password=* Outgoin