弗吉亚客户标准件规范.doc

弗吉亚客户标准件规范目次一顶出系统1.顶杆（DME）.订购举例2.司筒 (DME).订购举例二.滑块抽芯系统1.行位夹 （DME） 轻型载荷行位夹.订购举例 重型载荷行位夹.订购举例三冷却系统1.直头水嘴(LEGRIS) 订购举例2.弯头水嘴(LEGRIS) 订购举例3.旋转螺母(PARKER) 24锥球头密封旋转螺母订购举例24锥O型圈密封旋转螺母.订购举例4.旋转螺母90接头(PARKER) .订购举例5.端直通接头(PARKER) .订购举例6.水路快速接头(HASCO)订购举例7.直接头(PARKER).订购举例8.冷却橡胶管(PARKER) .订购举例四液压系统1.油缸（HPS VSM) 订购举例2.旋转螺母(PARKER).订购举例3.旋转螺母90接头(PARKER).订购举例4.端直通接头(PARKER).订购举例5.软油管(PARKER).订购举例五模具外围系统1.往复式气针(ShangHaiJiYa)订购举例 2.吊环.订购举例一顶出系统1. 顶杆（Ejector Pin）1.1.概述： 顶杆顶出是注塑模具中最常采用的顶出形式之一。1.2.顶杆的设计规范：顶杆的结构形状如图1.1，1.2，表1.1,1.2所示 图1.1：顶杆（EA系列）表1.1顶杆标准规格尺寸列表规格d2(0/-0.2)d1K(0/-0.06)RL(+2/+0)EA 1-L3120.2100,160EA 1.2-L31.220.2100,160EA 1.5-L31.51.50.2100,125,160,200EA 1.6-L31.61.50.2160,EA 1.7-L3.51.720.2100,200EA 2-L4220.2100,125,160,200,250,315,EA 2.2-L42.220.2100,125,160,200,250,315,EA 2.5-L52.520.3100,125,160,200,250,315,EA 2.7-L52.720.3100,125,160,200,250,315,EA 3-L6330.3100,125,160,200,250,315,400,500,EA 3.1-L63.130.3160,250EA 3.2-L63.230.3100,125,160,200,250,315,400,EA 3.5-L73.530.3100,125,160,200,250,315,400,EA 3.7-L73.730.3100,125,160,200,250,315,400,EA 4-L8430.3100,125,160,200,250,315,400,500,EA 4.1-L84.130.3250,EA 4.2-L84.230.3100,125,160,200,250,315,400,500,630,EA 4.5-L84.530.3100,120,160,200,250,315,400,EA 5-L10530.3100,125,160,200,250,315,400,500,630,800,EA 5.1-L105.130.3250EA 5.2-L105.230.3100,125,160,200,250,315,400,500,EA 5.5105.530.3100,125,160,200,250,315,400,500,EA 6-L12650.5100,125,160,200,250,315,400,500,630,800,1000EA 6.1-L126.150.5250,EA 6.2-L126.250.5100,125,160,200,250,315,400,500,630,EA 6.5-L126.550.5100,125,160,200,250,315,400,500,EA 7-L127.50.5100,125,160,200,250,315,400,500,630,EA 7.5-L127.550.5100,125,160,200,250,315,400,500,EA 8-L14850.5100,125,160,200,250,315,400,500,630,800,1000,1250EA 8.1-L148.150.5160,250,EA 8.2-L148.250.5100,125,160,200,250,315,400,500,630,800,EA 8.5-L148.550.5100,125,160,200,250,315,400,500,630,EA 9-L14950.5100,120,160,200,250,315,400,500,630,EA 9.5-L149.550.5100,120,160,200,250,315,400,500,EA 10-L161050.5100,120,160,200,250,315,400,500,630,800,1000,1250,1600,EA10.1-L1610.150.5250,EA10.2-L1610.250.5100,125,160,200,250,315,400,500,630,800,EA10.5-L1610.550.5100,125,160,200,250,315,400,500,630,EA 11-L161150.5100,125,160,200,250,315,400,500,630EA 12-L181270.8100,125,160,200,250,315,400,500,630,800,1000,1250,1600,EA 12.2-L1812.270.8100,125,160,200,250,315,400,500,630,800,EA 12.5-L1812.570.8100,125,160,200,250,315,400,500,630,800,EA 14-L221470.8100,125,160,200,250,315,400,500,630,800,1000,1250,1600,EA 14.2-L2214.270.8250,EA 16-L221670.8100,125,160,200,250,315,400,500,630,800,1000,1250,1600,1800EA 16.2-L2216.270.8250EA 18-L241870.8100,125,160,200,250,315,400,500,630,800,1000EA 20-L262081100,125,160,200,250,315,400,500,630,800,1000,1250,1600,1800EA 25-L3225101160,200,250,315,400,500,630,800,1000,1250,1600,1800EA 32-L4032101160,200,250,315,400,500,630,800,1000,1250,1600,1800 图：1.2顶杆（TA系列）表1.2顶杆标准规格尺寸列表规格d2(0/-0.2)d1K(0/-0.06)RL(+2/+0)TA 1.5-L31.51.50.2100,125,160,200TA 2-L4220.2100,125,160,200,250,315TA 2.2-L42.220.2100,125,160,200,250,315TA 2.5-L52.520.3100,125,160,200,250,315TA 2.7-L52.720.3100,125,160,200,250,315TA 3-L6330.3100,125,160,200,250,315,400,500TA 3.2-L63.230.3100,125,160,200,250,315,400TA 3.5-L73.530.3100,125,160,200,250,315,400TA 3.7-L 73.730.3100,125,160,200,250,315,400TA 4-L8430.3100,125,160,200,250,315,400,500,630TA 4.2-L84.230.3100,125,160,200,250,315,400,TA 4.5-L84.530.3100,125,160,200,250,315,400,630TA 5-L10530.3100,125,160,200,250,315,400,500,630,800TA 5.2-L105.230.3100,125,160,200,250,315,400,500,TA 5.5105.530.3100,125,160,200,250,315,400,500,TA 6-L12650.5100,120,160,200,250,315,400,500,630,800,1000TA 6.2-L126.250.5100,125,160,200,250,315,400,500,TA 6.5-L126.550.5100,125,160,200,250,315,400,500,TA 7-L12750.5100,125,160,200,250,315,400,500,TA 8-L14850.5100,125,160,200,250,315,400,500,630,800,1000TA 8.2-L148.250.5100,125,160,200,250,315,400,500,630,TA 8.5-L148.550.5100,125,160,200,250,315,400,500,630,TA 9-L14950.5100,125,160,200,250,315,400,500,630,TA 10-L161050.5100,125,160,200,250,315,400,500,630,800,1000,TA 10.2-L1610.250.5100,125,160,200,250,315,400,500,630,TA 10.5-L1610.550.5100,125,160,200,250,315,400,500,630,TA 11-L161150.5100,125,160,200,250,315,400,500,630,TA 12-L181270.8100,125,160,200,250,315,400,500,630,800,1000,TA 12.2-L 1812.270.8100,125,160,200,250,315,400,500,630,TA 12.5-L1812.570.8100,125,160,200,250,315,400,500,630,TA 14-L221470.8160,125,160,200,250,315,400,500,630,800,1000,TA 16-L221670.8160,125,160,200,250,315,400,500,630,800,1000,TA 18-L241870.8160,125,160,200,250,315,400,500,630,800,1000,TA 20-L262081160,125,160,200,250,315,400,500,630,800,1000,TA 25-L3225101160,125,160,200,250,315,400,500,630,800,1000,1.3.品牌标准件订购举例名称：顶杆 规格：EA 5-200 备注：DME标件名称：顶杆 规格：TA 5-200 备注：DME标件2. 司筒（Ejector Sleeve Assy S,KS(DME司筒)2.1.概述司筒主要适用于制品上螺钉柱等柱位的成型。2.2.司筒的设计规范司筒的形状如图2.1，2.2，表2.1，2.2所示：图2.1：司筒 （S型） 表2.1司筒标准规格尺寸列表规格d2d1dKRL2L1S 153-L631.520.22060,75,80,95,100,110,125,150,S 163-L631.620.22075,100,125,150,S 173-L631.720.22075,100,125,150,S 183-L631.920.22075,100,125,150,S 24-L94220.22575,100,125,150,170,175,200,S 224-L942.220.22575,100,125,150,170,175,200,S 255-L1052.520.22575,100,125,150,170,175,200,225,250,S 275-L1052.720.24575,100,125,150,170,175,200,225,250,S 285-L1052.920.245100,125,S 35-L105320.24575,100,125,150,170,175,200,225,250,S 325-L1053.220.24575,100,125,150,170,175,200,225,250,S 356-L1263.550.54575,100,125,150,170,175,200,225,250,S 376-L1263.750.54575,100,125,150,170,175,200,225,250,S 46-L126450.54575,100,125,150,170,175,200,225,250,S 428-L1494.250.54575,100,125,150,170,175,200,225,250,S 458-L1494.550.54575,100,125,150,170,175,200,225,250,S 58-L149550.54575,100,125,150,170,175,200,225,250,S 528-L1495.250.54575,100,125,150,170,175,200,225,250,S 610-L1610650.54575,100,125,150,170,175,200,225,250,275,300S 6210-L16106.250.54575,100,125,150,170,175,200,225,250,275,300S 6510-L16106.550.54575,100,125,150,170,200,225,250,275,300S 812-L2012870.84575,100,125,150,170,175,200,225,250,275,300,325,350S 8212-L20128.270.84575,100,125,150,170,175,200,225,250,275,300,325,350S 8512-L20128.570.84575,100,125,150,170,200,225,250,275,300S 1014-L22141070.84575,100,125,150,170,175,200,225,250,275,300,325,350S 10214-L221410.270.84575,100,125,150,175,200,225,250,275,300,325,350S 10514-L221410.570.85575,100,125,150,170,175,200,225,250,275,300,325,350S 1114-L22141170.85575,100,125,150,170,175,200,225,250,275,300,325,350S 1216-L22161270.84575,100,125,150,170,175,200,225,250,275,300,325,350S 12516-L221612.570.85575,100,125,150,170,175,200,225,250,275,300,325,350S 1418-L24191480.85575,100,125,150,170,175,200,225,250,275,300,325,350S 1620-L26201680.85575,100,125,150,170,175,200,225,250,275,300,325,350,375,400S 1822-L29221980.85575,100,125,150,170,200,225,250,275,300,325,350,375,400 图2.2：司筒（KS）表2.2司筒标准规格尺寸列表规格d2d1dKRL2L1KS 153-L631.530.33560,75,100,125,150,175,200,225,250,KS 163-L631.630.33560,75,100,125,150,175,KS 173-L631.730.33575,100,125,150,KS 183-L631.830.33575,100,125,150,KS 24-L84230.33560,75,100,125,150,170,175,200,225,250,275,300,325,KS 224-L842.230.33560,75,100,125,150,170,175,200,225,250,KS 255-L1052.530.33560,75,100,125,150,170,175,200,225,250,275,KS 275-L1052.730.34560,75,100,125,150,175,200,225,250,275,KS 35-L105330.34560,75,100,125,150,170,175,200,225,250,275,KS 325-L1053.230.34560,75,100,125,150,170,175,200,225,250,275,KS 356-L1263.550.54560,75,100,125,150,170,175,200,225,250,275,300KS 376-L1263.750.54560,75,100,125,150,170,175,200,225,250,275,300KS 46-L126450.54560,75,100,125,150,170,175,200,225,250,275,300325,350,400,KS 428-L1484.250.54560,75,100,125,150,170,175,200,225,250,275,300,325,KS 458-L1484.550.54575,100,125,150,170,200,225,250,KS 58-L148550.54560,75,100,125,150,170,175,200,225,250,275,300,325,350,KS 528-L1485.250.54560,75,100,125,150,170,175,200,225,250,275,300,325,KS 558-L1485.550.54560,75,100,125,150,175,200,225,250,275,300,325,KS 610-L1610650.54560,75,100,125,150,170,175,200,225,250,275,300,325,350,KS 6210-L16106.250.54560,75,100,125,150,170,175,200,225,250,275,300,325,350,KS 6510-L16106.550.54560,75,100,125,150,170,175,200,225,250,275,300,325,350,KS 812-L2012870.94560,75,100,125,150,170,175,200,225,250,275,300,325,350,400KS 8212-L20128.270.94560,75,100,125,150,170,175,200,225,250,275,300,325,350,400KS 8512-L20128.570.94560,75,100,125,150,170,175,200,225,250,275,300,325,350,400KS 1014-L22141070.94575,100,125,150,170,175,200,225,250,275,300,325,350,400,450,500KS 10514-L221410.570.95575,100,125,150,175,200,225,250,275,300,325,350,400,450,KS 1114-L22141170.95575,100,125,150,175,200,225,250,275,300,325,350,400,450,KS 1216-L22161270.94575,100,125,150,170,175,200,225,250,275,300,325,350,400,450,500KS 12516-L221612.570.95575,100,125,150,170,175,200,225,250,275,300,325,350,400,450,500KS 1418-L24181490.95575,100,125,150,170,175,200,225,250,275,300,325,350,400,450,KS 1620-L26201690.95575,100,125,150,170,200,225,250,275,300,325,350,375KS 1822-L28221890.95575,100,125,150,170,200,225,250,275,300,325,350,3752.3.品牌标准件订购举例：名称：司筒 规格：S 153-150 备注：DME标准件名称：司筒 规格：KS 153-250 备注：DME标准件二.滑块抽芯系统3. 行位夹 （Slide Retainer）3.1.概述：行位夹，DME品牌标准件，对应规格为PSM、MRT两种型号。3.2.轻型载荷-行位夹设计规范： 如图3.1，表3.1所示 图3.1： 轻型载荷行位夹表3.1序号型号IMLBAK载荷(max Nm)1PSM 000125.534.510.019388102PSM 000238.046.014.5325410153PSM 000351.070.022.5458612203.3.重型载荷-行位夹设计规范：如图3.2，表3.2所示 图3.2： 重型载荷行位夹表3.2序号型号IGHBAK载荷(max.Nm)1MRT 10M25192619388102MRT 20M382436325410153MRT 40M513656458612203.4.品牌标准件订购举例：名称：行位夹 规格:PSM 0001 备注：DME标准件名称: 行位夹 规格:MRT 10M 备注：DME标准件三冷却系统1. 直头水嘴(Water Connector)1.1.直头水嘴设计规范：如图1.1，1.2，表1.1，1.2所示 图：1.1 直头水嘴表1.1：型号DC型号DC3101 06 196M53101 10 1310G1/43101 06 556M73101 10 1710G3/83101 06 606M103101 10 2110G1/23101 06 676M123101 12 1312G1/43101 06 106G1/83101 12 1712G3/83101 06 136G1/43101 12 2112G1/23101 06 176G3/83101 14 1714G3/83101 06 216G1/23101 14 2114G1/23101 08 608M103101 08 678M123101 08 108G1/83101 08 138G1/43101 08 178G3/83101 08 218G1/21.2.品牌标准件订购举例：名称：直头水嘴 规格：3101 06 19 备注：LEGRIS标准件2. 弯头水嘴2.1.弯头水嘴设计规范: 如图2.1，表2.1所示 图2.1：弯头水嘴表2.1型号DC型号DC3199 06 196M53199 10 1310G1/43199 06 556M73199 10 1710G3/83199 06 106G1/83199 10 2110G1/23199 06 136G1/43199 12 1312G1/43199 06 176G3/83199 12 1712G3/83199 06 216G1/23199 12 2112G1/23199 08 108G1/83199 14 1714G3/83199 08 138G1/43199 14 2114G1/23199 08 178G3/83199 08 218G1/22.2. 品牌标准件订购举例：名称：弯头水嘴 规格：3199 06 19 备注：LEGRIS标准件3. 旋转螺母3.1.概述：旋转螺母，接头用于Push-Lok软管，PARKER标准件。3.2.轻型系列-24锥球头密封旋转螺母设计规范： 如图6.1，表6.1所示 图3.1：24锥球头密封旋转螺母表3.1.型号软管内径公制螺纹TubeO.D.MmAmmBmmWmmDNInchSizemm3C382-15-8121/2-812.7M22X1.5154215273.3.轻型系列-24锥O型圈密封旋转螺母设计规范： 如图3.2，表3.2所示 图3.2： 24锥O型圈密封旋转螺母表3.2.型号软管内径公制螺纹TubeO.D.MmAmmBmmWmmDNInchSizemm3CA82-15-8121/2-812.7M22X1.5154418273CA82-12-6103/8-69.5M18X1.5124017223CA82-10-6103/8-69.5M16X1.5104017193.4.品牌标准件订购举例：名称：旋转螺母 规格：3C382-15-8 备注：PARKER标准件 名称：旋转螺母 规格：3CA82-15-8 备注：PARKER标准件4. 旋转螺母90弯头4.1.概述：旋转螺母90弯头， PARKER标准件。4.2.轻型系列-旋转螺母90弯头设计规范：如图4.1，表4.2所示 图4.1 ：24锥O型圈密封旋转螺母90弯头表4.1. 型号软管内径公制螺纹TubeO.D.MmAmmBmmEmmW mmDNInchSizemm3CF82-15-8121/2-812.7M22X1.515583241273CF82-12-6103/8-69.5M18X1.512492736223CF82-10-6103/8-69.5M16X1.510492735194.3.品牌标准件订购举例： 名称：旋转螺母90接头 规格：3CF82-15-8 备注：PARKER标准件5. 端直通接头5.1.概述：端直通接头，PARKER标准件。5.2.端直通接头设计规范： 如图5.1，表5.1图5.1： 端直通接头表5.1.型号D1T1D3D4L1L2L3L4S1S2PN(bar)CFA3C71MSGE15LR3/8EDOMD15G3/8A92232.513.512.0292427400315315200GE12LR1/4EDOMD12G1/4A61931.012.012.0271922400315315200GE10LR1/8EDOMD10G1/8A41425.510.58.02517195003153152005.3.端直通接头设计规范：如图5.2,表5.2 图5.2： 端直通接头表5.25.3. 品牌标准件订购举例:名称：端直通接头 规格：GE15LR3/8EDOMDA3C 备注：PARKER标准件名称：端直通接头 规格：6-2FTX-S 备注：PARKER标准件6. 水路快速接头6.1.水路快速接头6.2.水路快速接头Z81系列设计规范 如图6.1,表6.1 图6.1:水路快速接头Z81系列表6.16.2.水路快速接头Z80系列设计规范 图6.2:水路快速接头Z80系列表6.2 图6.3:水路快速接头Z80系列表6.36.3.品牌标准件订购举例：名称：水路快速接头 规格：Z81/13/R1/4 备注：HASCO标准件名称：水路快速接头 规格：Z801/13 .备注：HASCO标准件名称：水路快速接头 规格：Z801/13/90 备注：HASCO标准件7. 直接头7.1.概述：直接头， PARKER标准件。7.2.直接头设计规范：如图7.1，表7.1所示 图7.1 ：直接头表7.1. 7.3.标准件订购举例： 名称：直接头 规格：3/8 GG-S 备注：PARKER标准件8. 冷却橡胶管8.1.概述： 冷却橡胶管为合成橡胶内胶层，一层纤维编织增强层，黑色，绿色，蓝色，和红色合成橡胶外胶层。高压系列，Parker标准件。8.2.冷却橡胶管规格参数：表8.1：高压系列型号软管内径软管外径额定压力最大工作压力 最小爆破压力真空度千帕最小弯曲半径重量DNInchSizemmmmMPapsiMPapsiabsmmkg/m831-4-RL61/4-46.312.72.43509.714006650.13831-6-RL103/8-69.515.92.03008.312006750.16831-8-RL121/2-812.719.82.03008.3120061300.27831-10-RL165/8-1015.923.02.03008.31200501500.28831-12-RL203/4-1219.126.22.03008.31200501800.36注：订购时需标明Push lok软管型号以及规格和颜色。例：831-4-GRN-RL (绿色) 颜色代码： BLU=蓝色；RED=红色；GRN=绿色；BLK=黑色。温度范围:-40/+100,空气最高+70,水最高+85。表8.2：低压系列型号软管内径软管外径额定压力最大工作压力 最小爆破压力真空度千帕最小弯曲半径重量DNInchSizemmmmMPapsiMPapsiabsmmkg/m801-4-RL61/4-46.312.71.72506.810006650.13801-6-RL103/8-69.515.91.72506.810006750.16801-8-RL121