已阅读5页,还剩27页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
BRC GLOBAL STANDARD FOOD ISSUE 4 - CHECKLISTNOTESIn the Met column there are only three possible types of entry: Y (a tick is an acceptable alternative) indicating Yes for compliance N (a cross is an acceptable alternative) indicating No for a non compliance NA indicating that that requirement is not relevant to this type of operation and so neither Y or N is meaningfulFor all N or cross entries indicating a non-conformity against a requirement at the level being sought there must be a CAR issued. For all NA an entry must be made in the checklist and the Evaluation Report explaining the reason for being not applicable.For clauses in compliance, it maybe considered there are opportunities for improvement that should be reported. The comments column should be used to indicate CRITICAL / MAJOR / MINOR CAR.ClauseRequirementMetComments & ObservationsHACCP SYSTEMThe basis of the companys food safety control system shall be a HACCP Plan which shall be systematic, comprehensive, thorough, fully implemented and maintained and shall be based on the Codex Alimentarius HACCP principles and reference shall be made to relevant legislation, codes of practice or guidelines.FUNDAMENTAL1.1Senior Management commitment & implementation in QMS1.2HACCP system multidiscipline teamUse of consultantsDay to day management1.3Team Leader competence1.4Team members training and experience1.5Support programmes e.g. QA and GMP1.6HACCP principles used1.6.1Hazard analysis 1.6.2CCPs 1.6.3Critical limits 1.6.4Monitoring control of CCPs1.6.5Corrective actions1.6.6Validation and verification1.6.7DocumentationClauseRequirementMetComments & Observations1.7Risk analysis1.7.1Occurrence and severity.1.7.2Qualitative and or quantitative evaluation1.7.3Micro-organisms1.8Applicability, practical, effective and reviewed1.9Conformance and corrective action recordsQUALITY MANAGEMENT SYSTEM2.1Quality Management System - General RequirementsThe company shall have a defined Quality Management System in relation to the Standard that is established, documented, implemented, maintained, reviewed and where appropriate, improvedFUNDAMENTAL2.2Quality Policy StatementThe company shall have a clearly defined and documented authorised quality policy statement.2.2.1Companys intentions 2.2.2Senior management communication 2.2.3Understanding of policy 2.2.4Communications and review2.3Quality ManualThe company shall have a Quality Manual which states the companys commitment to quality and has a scope which covers the requirements of this Standard.2.3.1Implementation2.3.2Working methods and practices2.3.3AvailabilityClauseRequirementMetComments & Observations2.4Organisational Structure, Responsibility and Management Authority.The company shall have an organisational structure which ensures job function, responsibility and reporting relationships of those staff whose activities affect product safety, legality and quality are clearly defined and documented.2.4.1Directors responsibilities 2.4.2Responsibility levels & job descriptionsAbsence of key staff2.4.3Information support & monitoring of QMS2.4.4Updates on legislation, food safety, technical developments etc2.4.5Description of duties or work instructions2.5Management CommitmentThe companys senior management shall be fully committed to the development, implementation and improvement of the Quality Management System.2.5.1Quality objectives2.5.2Process for identification of safety or legal issues Documentation2.6Customer FocusThe companys senior management shall ensure that processes are in place to determine their customers needs and expectations, to clearly define their requirements and ensure that these requirements are fulfilled.2.6.1Performance indicators 2.7Management ReviewThe companys senior management shall review the effectiveness of the Quality Management and HACCP Systems at planned intervals. The review shall ensure a critical evaluation of the Systems suitability, adequacy and effectiveness, and identify the need for change.2.7.1Records2.7.2Communication of decisions & actionsClauseRequirementMetComments & Observations2.7.3Review to include Audits Customer feedback Process performance Product conformity Preventative & corrective actions Review of management reviews Changes on QMS Recommendations 2.8Resource ManagementThe companys senior management shall provide all the resources required to implement and improve the processes of the Quality Management and HACCP systems.2.9Internal AuditThe company shall audit those systems and procedures, which are critical to product safety, legality and quality to ensure they are in place, appropriate and complied with.2.9.1Appropriateness of frequency 2.9.2Competency of auditors.2.9.3Record of internal audits, corrective actions and verification2.9.4Results to those concerned corrective actions and time scales2.9.5Record to demonstrate compliance2.10PurchasingThe company shall control all its purchasing processes, which are critical to product safety, legality and quality to ensure product and services procured conform to defined requirements.2.10.1Supplier Approval and Performance MonitoringThe company shall operate procedures for approval and the monitoring of its suppliersDocumented supplier approval procedure Exceptions ClauseRequirementMetComments & ObservationsCriteria and standards. In- house checks Certificates of analysis Supplier inspectionPerformance review2.11General Documentation RequirementsThe company shall document procedures to demonstrate compliance with the Standard and shall ensure that all documents necessary to demonstrate the effective operation and control of the processes underpinning this compliance are in place.2.11.1Documentation ControlThe company shall ensure that all documents, records and data critical to the management of product safety, legality and quality are in place and effectively controlled.Authorised and versionLegible, unambiguous, detail, correct application and accessibleReasons for changes or amendment recordedObsolete documentationRetention of documents and records2.11.2SpecificationsThe company shall ensure that appropriate specifications exist for: raw materials (including packaging materials) finished products intermediate/semi processed products (where appropriate) any products or service which could affect the integrity of the finished productAdequacy & accuracyFormal agreementsReviewsClauseRequirementMetComments & Observations2.11.3ProceduresThe company shall have, and operate in accordance with written detailed procedures, instructions, and reference documents to cover all processes critical to product safety, legality and quality.Legibility, unambiguous and accessible document2.11.4Record KeepingThe company shall maintain records to demonstrate the effective control of product safety, legality and quality.Legibility and genuine.Collation, review, maintenance, storage and retrieval Amendment authorisation2.12Corrective ActionThe company shall ensure procedures exist to investigate the cause of significant non-conformity against standards, specifications and procedures, which are critical to product safety, legality and quality.FUNDAMENTAL2.12.1Corrective actions taken2.12.2Plan responsibility 2.12.3Documented responsibility and accountability.2.13TraceabilityThe company shall have a system with the ability to trace materials(including primary packaging materials) from source through all stages of processing and distribution of the finished product to the customer.FUNDAMENTALAuditor Note:Undertake Traceability Challenge 2.13.1System testing2.13.2Identity preservation2.13.3ReworkClauseRequirementMetComments & Observations2.14Management of Incidents, Product Withdrawal and Product RecallThe company shall effectively manage incidents and have effective product withdrawal and product recall procedures in place.2.14.1Written guidance on what constitutes an “incident” and reporting procedure 2.14.2Customers notification 2.14.3Documented Product Recall procedureAppropriateness, formalisation and review 2.14.4Testing of procedure2.14.5Corrective action and review 2.15Complaint HandlingThe company shall have a system for the management of product complaints.2.15.1Appropriate actions 2.15.2Use of complaint data 3.FACTORY ENVIRONMENT STANDARDS3.1.External Environment Standards3.1.1LocationThe site shall be located and maintained so as to prevent contamination and enable the production of safe and legal products.Local activities Site boundaries.3.1.2Perimeter and GroundsAll grounds within the site shall be finished and maintained to an appropriate standard.Good order and well maintainedClean and unobstructed area. ProceduresOutside storageDrainageClauseRequirementMetComments & Observations3.2Internal Environment Standards3.2.1Layout, Product Flow and SegregationPremises and plant shall be designed, constructed and maintained and procedures shall be in place to control the risk of product contamination and to comply with all relevant legislation.FUNDAMENTALSite security and authorised accessProcess flow Barriers or procedures for contaminationSystems of workingSegregation designEffective segregation for specific handling requirementsHigh risk areasHigh care areasTransfer points high risk/low risk0Impact of on site laboratory1Washing and cleaning segregation of trays and utensils2Sufficient space3.2.2Fabrication- Raw Material Handling, Preparation, Processing, Packing and Storage areas.The fabrication of the site, buildings and facilities shall be suitable for the intended purpose. Walls.1Wall design, construction, finish and maintenance Floors.1Design, impervious and maintenance .2Drainage design and maintenance .3Drains from laboratories.4Floor falls ClauseRequirementMetComments & Observations Ceilings/overheads.1Ceilings and overheads design, construction, finish and maintenance.2Access to false ceilings Windows.1Open window design .2Protection for glass window breakage. Doors.1External doors Lighting.1Lighting for work areas.2Protection of bulbs and strip lights. Air Conditioning/Ventilation.1Adequate ventilation .2Maintenance of screened or filtered air equipment .3Positive air pressure3.3ServicesAll services to and within the production and storage areas shall be designed, constructed, maintained and monitored to control the risk of product contamination.3.3.1Water supply 3.3.2Monitoring of services 3.4EquipmentEquipment shall be suitably designed for the intended purpose and shall be used so as to minimise the risk of contamination of product.3.4.1Equipment specification, maintenance and operation3.4.2Equipment accessClauseRequirementMetComments & Observations3.5MaintenanceA system of planned maintenance shall be in place covering all items of equipment which are critical to product safety, legality and quality.3.5.1Programme for new equipment and plant3.5.2Impact of maintenance 3.5.3Temporary repairs.3.5.4Cleaning or replacing light fittings and glass 3.6Staff FacilitiesStaff facilities shall be designed and shall be operated so as to minimise the risk of product contamination.3.6.1Designated changing facility, and clothing 3.6.2Hand washing facilities3.6.3Toilets3.6.4Smoking areas3.6.5Catering facilities3.6.6Storage of staff food3.6.7Siting of changing facilities 3.6.8Specially designated changing facilities for high risk areas3.6.9Outdoor clothing and personal items storage.3.7Physical and Chemical Product Contamination RiskAppropriate facilities and procedures shall be in place to control the risk of physical or chemical contamination of product.3.7.1Storage facilities for chemicals3.7.2Contamination audits and corrective action3.7.3All glass and similar material register3.7.4Written procedures for handling glass and hard clear plastic breakage3.7.5Incident reports3.7.6Incompatible materials3.7.7Use of woodClauseRequirementMetComments & Observations3.8Housekeeping and HygieneHousekeeping and cleaning systems shall be in place which ensure appropriate standards of hygiene are maintained at all times and the risk of contamination is minimised.FUNDAMENTAL3.8.1Documented cleaning schedules3.8.2Cleaning practices 3.8.3Cleaning and housekeeping practice and records3.8.4Cleaning chemicals3.8.5Verification of cleaning and sanitation effectiveness3.8.6Disinfection processes3.9Waste/Waste DisposalThere shall be adequate systems for the collection, collation and disposal of waste material.3.9.1Minimisation of accumulation of waste3.9.2Meet legislative requirements. Use of licensed contractors3.9.3External waste collection containers and compactors 3.9.4Third party usage for trademarked materials3.10Pest ControlThe Company shall be responsible for minimising the risk of pest infestation on the site.3.10.1Competent pest control 3.10.2Pest control plan/diagram3.10.3Identification and checking of process equipment3.10.4Use of results data 3.10.5Detailed records3.10.6Electric fly killers and/or pheromone traps3.10.7Screens and traps on drains 3.10.8Checking for pest infestation on incoming raw materials3.10.9Storage areas3.10.10Documentation on safe useClauseRequirementMetComments & Observations3.11TransportAll vehicles used for the transportation of raw materials (including packaging) to the premises ,and the dispatch of intermediate /semi processed product and finished product to the customer or further storage facilities shall be suitable for the purpose, maintained in good repair and in a hygienic condition.Where a company employs third-party contractors, all the requirements specified within section 3.11 shall be defined within a contract and effectively managed.3.11.1Documented maintenance and hygienic procedures3.11.2Procedures for secure conditions3.11.3Procedures for cross contamination3.11.4Adequacy of refrigerated transport3.11.5Procedures form contract refrigerated transport3.11.6Refrigerated transport temperature data logging devices3.11.7Procedures for taint uptake3.11.8Protection of material during loading/unloading3.11.9Breakdown procedures4.PRODUCT CONTROL4.1Product Design/DevelopmentA hazard analysis study shall be undertaken during the product design/development to identify and assess all potential safety hazards and associated risks.4.1.1Factory trials and testing 4.1.2Legal labelling4.1.3Documented product design/development process4.1.4Establishment of shelf life 4.1.5Documented shelf life trialsClauseRequirementMetComments & Observations4.2Handling Requirements for Specific MaterialsWhere raw materials and finished product require special handling procedures (e.g. known allergies, product certified to organic or assured standard status), handling requirements shall be in place to ensure that product safety, legality and quality are maintained.FUNDAMENTAL4.2.1Risk assessment4.2.2Cross contamination4.2.3Rework procedures implemented4.3Metal Detection/Foreign Body DetectionThe company shall ensure all necessary steps are taken to identify, avoid, eliminate or minimise the risks of metal or foreign body contamination.4.3.1CCP determination of need and situation4.3.2Best practice and critical limits4.3.3Detector incorporates one of the following:1. Alarm or belt stop2. Automatic rejection3. Location and segregationCorrective action procedures following detection4.3.4Procedures for operation, monitoring etc.4.3.5Procedures following failure of detector4.4Product PackagingProduct packaging shall be appropriate for the intended use and stored under conditions to minimise the risk of contamination and deterioration.4.4.1Specification procedures4.4.2Compliance with food safety legislation4.4.3Storage4.4.
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- Unit 7 Where does he come from?第1课时教学课件
- 事业单位文秘岗面试专业面试强化训练
- 事业单位宣传岗面试易错题题库及答案
- 养老机构防走失管理培训
- 填埋场污染源自动监控运维规范
- 游泳馆池体防水冬季施工方案
- 填埋场恶臭污染物排放管控方案
- 综合管理部办公资产管理员岗位职责
- 养老服务机构老人满意度提升实施方案
- 2026浙江杭州余杭区中泰小学招聘教师1人笔试参考题库及答案解析
- 2026北京市朝阳区卫生健康委员会所属事业单位第二批招聘241人笔试备考题库及答案解析
- 4.1妈妈教学设计
- 2026年内蒙古中考语文试卷及答案
- 神经内科诊疗新技术
- 成人术中外周静脉输液技术操作及管理指南
- 110kV变电站电气调试实施方案
- 八年级物理第二学期期中考试质量分析
- 2026-2030中国化机浆市场竞争规划与未来前景发展趋势研究报告
- 2026粉末冶金开发高速钢刀片脱模剂适用性分析报告
- 宝坻社保协管员模拟考试试题及答案
- 三角函数压轴题专项训练-2026年高考数学 含答案
评论
0/150
提交评论